I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...
02:27:22:161 11f0 ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166 11f0 DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171 11f0 DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446 ca0 DCR: weak share, skip
02:27:23:291 6ac DCR: weak share, skip
02:27:23:761 408 GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766 408 em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766 408 watchdog - thread 0, hb time 203
02:27:23:771 408 watchdog - thread 1, hb time 94
02:27:23:771 408 watchdog - thread 2, hb time 0
02:27:23:771 408 watchdog - thread 3, hb time 125
02:27:23:776 408 watchdog - thread 4, hb time 31
02:27:23:776 408 watchdog - thread 5, hb time 141
02:27:23:781 408 watchdog - thread 6, hb time 219
02:27:23:781 408 watchdog - thread 7, hb time 110
02:27:23:786 408 watchdog - thread 8, hb time 94
02:27:23:786 408 watchdog - thread 9, hb time 203
02:27:23:791 408 watchdog - thread 10, hb time 77656
02:27:23:791 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796 408 watchdog - thread 11, hb time 77547
02:27:23:801 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806 408 Restarting OK, exit...
This is how my *.bat file looks
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40
What can be wrong, any advice?
Try not to push your GPU5 too hard... you must be running at 2250mhz
solutions for you:
1. Find out which one is GPU5
2. back to stock setting and slowly work your way up (2100 or 2125 mem is a good start.. )
2. Try ramp up the Fan speed (I saw your temp very high 85C)
3. Continue monitoring
ok, I will try to reset that card, any advice what voltage settings I should have?
If this not solve it I will change raiser and see if it works better with another.
I am running at 2200mhz memory @ 940mV, and 1100 core clock @ 950mV. I am running the same setting for all cards. I have fan speed max set to 3200 (I dont really understand WattMan's fan settings??), can I make the fan always go on 70% speed? Because the noice is not a problem.