Re: [Mining OS] SimpleMining.net - Easy to use GPU MINING Operating System

I have a Sapphire Radeon RX 470 MINING Edition 8192MB GDDR5 Samsung PCI-Express Graphics Card, and I am the following settings for simplemining

Code:

-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal obfuscated.test1/obfuscated@gmail.com -dpsw x

on claymore-eth-v9.7
It is reporting the following speeds 15.37 MH/s 461.22 MH/s
Does this seem a reasonable speed for this single card? I have never dual mined nor used this card before so I am unsure on what type of hash speeds I should be getting.

Thanks.

Use the flag below(Taken from the claymore 9.xxx readme txt file), this balances out how much hashing power you want between your main and secondary coins

-dcri   Decred/Siacoin/Lbry/Pascal intensity, or Ethereum fine-tuning value in ETH-only ASM mode. Default value is 30, you can adjust this value to get the best Decred/Siacoin/Lbry mining speed without reducing Ethereum mining speed.
   You can also specify values for every card, for example "-dcri 30,100,50".
   You can change the intensity in runtime with "+" and "-" keys and check current statistics with "s" key.
   For example, by default (-dcri 30) 390 card shows 29MH/s for Ethereum and 440MH/s for Decred. Setting -dcri 70 causes 24MH/s for Ethereum and 850MH/s for Decred.

for me I find -dcri 40 seems a good balance, but tweak and tune to taste

Hi toomeke, thanks for the reply, could you give me some further help with your comment, I have tried setting "-dcri 30", -dcri 50" and -dcri 100" non of which make a difference below is an example of the change I made

Code:

-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal obfuscated.test1/obfuscated@gmail.com -dpsw x
To
-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -dcri 30 x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dcri 30 obfuscated.test1/obfuscated@gmail.com -dpsw x

Which does not seem to change anything.

dcri- flag only needed once, it doesnt matter where you add the flag, but I like to keep the tweaks on the end like this

-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal obfuscated.test1/obfuscated@gmail.com -dpsw x -dcri 30

Hi, thanks, I have tried the following values
09 23.24 MH/s 209.19 MH/s
10 23.32 MH/s 233.19 MH/s
20 20.27 MH/s 405.44 MH/s
30 14.97 MH/s 449.16 MH/s
40 12.35 MH/s 494.13 MH/s
50 10.28 MH/s 513.87 MH/s

So I need to find out the best ratio of what to mine giving the current values of eth and pascal, as well as overclocking values.

How do I find the default memory MHz and core MHz for my card?

Sweet, have a play and workout the best ROI(Use this and input the rates and power https://whattomine.com/merged_coins/10-eth-pasc), default clock? just input core and memory as zero/0 then let it run for a min, and you will see then tune from there, Id tune mining ether only, then add your 2nd coin and finetune off that using dcri/extra clocks etc

Get it stable but dont bother trying to get that last 5% more hash as it will often waste your mining and personal time...lol

Thanks, I set the defaults to 0 so they would reset after messing around with them last night, now it at 300 (7) / 1750 and the hash rate has dropped right down to 7.84 MH/s 78.35 MH/s, it does not seem to know the original values and I did not take a record of them!

I got it back to normal by restarting the rig, made a note of the clock this time

Code:

1236(7)/1750

so should I be upping both values at the same time? for example

Code:

1246(7)/1760

+10 at a time?