Quote from: htautosjay on June 22, 2018, 06:32:44 AM

I personally think the 650M Firmware, leaving it at 650Mhz is what you are looking for that will give you 13,900 Th with no temp rises, the temp rise from what i see is that the Auto Adjust Fq firmware the fans run up to 6000 which keeps them cooler, where the fans on 600M and 650M run to about 4600.. the HW faults come from a poor pool from my experience, do you use Slush?..they seem to be the cleanest

Ok ran at 650M and 662M for a week now, went up to 668M and running completely fine hashing 14,300Th temps are stable at 82.

Quote from: RadekG2 on June 18, 2018, 07:10:11 PM

[...]

Hay buddy, I have been running these S9's for almost a week at 14,300, 14,400 Th but i dont see much movement in the chip temps they seem static at 81, 82..maybe that is the temps,, do you have the same readings?..
In the Kernal log it says :

Code:

set FAN speed according to: temp_highest=82 temp_top1[PWM_T]=82 temp_top1[TEMP_POS_LOCAL]=72 temp_change=0 fix_fan_steps=-15
FAN PWM: 54
read_temp_func Done!
CRC error counter=0

Cheers
Jase

Is this Ok? It says Warning Chain has no temp will fix it..

Code:

max freq = 675
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:51 remote:51 offset:32
Chain[J6] chip[244] get middle temp offset=32 typeID=55
Chain[J6] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it[/b][/size][/size]
New offset Chain[5] chip[244] local:48 remote:49 offset:31
Chain[J6] chip[244] get middle temp offset=31 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:43 remote:45 offset:29
Chain[J7] chip[244] get middle temp offset=29 typeID=55
Chain[J7] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:42 remote:43 offset:30
Chain[J7] chip[244] get middle temp offset=30 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:43 remote:46 offset:28
Chain[J8] chip[244] get middle temp offset=28 typeID=55
Chain[J8] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
New offset Chain[7] chip[244] local:41 remote:44 offset:28
Chain[J8] chip[244] get middle temp offset=28 typeID=55
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
setStartTimePoint total_tv_start_sys=33762 total_tv_end_sys=33763
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08