Post
Topic
Board Announcements (Altcoins)
Re: [ANN] Resurrection of Sprouts Classic 2% Daily APR Interest, 730% a year
by
cryptomob
on 12/10/2018, 18:58:47 UTC
hi guys, need a bit of help here:

new classic wallet invalidated all transactions since September 10, and i reloaded entire chain with new wallet and it was stuck and not updating chain even though in conf file i added nodes and i had connections in qt.

used instructions on how to fix wallet, and now i have that exception: 11db exception not enough space. that's after i repaired wallet.  also after repair all stakes since sept 10 showed orphaned.

transactions from tradesatoshi went through, staking works.

is it ok to keep it like that with an error message or is there a further fix?

also, i have unconfirmed amount sitting there for about 10 days... please advise how to fix it.

last question: could any one confirm that 2 billions is not a limit anymore and it is safe to combine larger inputs. and if yes - what is good input size to produce a stake shortly after maturity?

for those asking if smaller amount like 70-80 mils will stake - yes, it may take very long time though.  i have an input of 77,7 mils sitting there for 117 days with a chance to stake of 39.98% within the next 24 hours.  

thank you!

Hi cryptomob,

Are you able to try the repairwallet again with regards to the 11db exception:

Click on the Help menu
Click on Debug window
Click on the Console button
In the console type 'repairwallet' and hit the enter key
Close and re-open the Sprouts Classic wallet
@cryptomob
Quote
...invalidated all transactions since September 10...
...all stakes since sept 10 showed orphaned...
These are signs that your on the wrong chain.
(fixing this problem first might remove the other error)

The solution is to delete all of the files in the data directory (except wallet.dat), install the latest version from the OP, and re-sync.
So, be sure you have saved a copy of your current wallet.dat file, before trying anything.

...


thank you for detailed answer, arcmetal, appreciate it much.  error in qt appeared after i ran repair wallet from debug tab.  should i do it again?

Running debug again will most likely give you the same result.

From what you describe it seems possible that you are running an old version of the sprouts wallet.  It would explain the errors you are getting.  

While the wallet exe is open, check which version you are running.
Go to:  help >> about sprouts

It should say:  v0.1.2.3-gd0cbc83

-----
Other than the above, if I were you I'd do the following:

1. first make a backup of my "wallet.dat" file, save it on another PC or a separate flash drive, etc.,
2. delete, remove any other files on the hard drive that are associated with "sprouts",  
delete any folders that the old sprouts may have created, or any old desktop files that point to sprouts,
3. start over with the latest copy of the new wallet listed in the OP,
4. use the latest list of addnodes in a new sprouts.conf file,
5. finally, after the new wallet is installed and fully synced, then go back and replace your "wallet.dat" file (that has your coins) into the new sprouts data directory.
The new data directory could be located here: C:\Users\username\AppData\Roaming\Sprouts


It could be that an old pointer on the desktop is still pointing to an old version of the sprouts wallet, and so this could be causing you problems.

man, you are all about details!!! thank you very much. my wallet version is as you described, Sprouts Classic v0.1.2.3-gd0cbc83.

i have started from saving wallet.dat, and then from new data dir.  if anything - i will do it again, but its hard to expect it to behave different since i have done already synch from scratch and then replaced wallet.dat with my old wallet after full synch.  nodes are added from the latest posts. 

test deposit to tradesatoshi went through.

i think i will keep it the way it is for as long as it works Smiley  and, OMG it stakes!!!! Smiley

either way, appreciate your support, way to go!

have a good one.