Wiring:

• Plug one 4 pin cable connected from the 4 pin header on the unit to the micro USB adapter.
• Connect a micro USB to USB cable to the micro USB adapter, and then plug this into your controller.
• More units can be added by plugging another 4 pin cable from the second unit to the first unit's other 4 pin header.
• Plug in a /hCQilO]network cable from the WR703N to your router, and power it on.

Configuration:

• Power on the power supply using its switch at the back.
• Make sure or your router's subnet is 0, ie 192.168.0.x. If not then change it to 0, this is just temporary. ***If this is not possible, see below***
  
• Using a browser, navigate to 192.168.0.100 - this goes to the WR703N's configuration page.
• Login using "root" as the username.
• Navigate to Network -> Interfaces -> WAN -> Edit.
• Change protocol to DHCP and click "Save & Apply".
• Using a browser, navigate to your router and find the IP it has assigned the WR703N and navigate to that IP.
• Navigate to the page Status -> Miner Configuration. Enter your pool information in the below format.
• Navigate to the page "Miner Status" to check mining has started.
• You can then change your router subnet back to whatever you are used to using.

Alternative Subnet Change:

• Unplug your computer from all internet sources.
• Plug in an ethernet cable from the WR703N to your computer.
• Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings.
• Right click on your ethernet adapter -> Properties.
• Click on "Internet Protocol Version 4" and click properties.
• Select "Use the following IP address" and enter the following:
• IP Address: 192.168.0.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.0.100.
• Plug in an ethernet cable from the WR703N to you router.
• Restart the configuration instructions as above.

Wiring:

• Plug one 4 pin cable connected from the 4 pin header on the unit to the micro USB adapter.
• Connect a micro USB to USB cable to the micro USB adapter, and then plug this into your controller.
• More units can be added by plugging another 4 pin cable from the second unit to the first unit's other 4 pin header.
• Plug in a /hCQilO]network cable from the WR703N to your router, and power it on.

Configuration:

• Put the SD card into another computer.
• /jtdHMl]Download the RasperryPi Avalon 4 OS image (sdcard-vfat-ext4.img)
• /A22fj5]Download the Win32 Disk Imager and use it to flash SD card with this image.
• Put SD card into RaspPi and power it on.
• Power on the power supply using its switch at the back.
• Make sure or your router's subnet is 0, ie 192.168.0.x. If not then change it to 0, this is just temporary. ***If this is not possible, see below***
  
• Using a browser, navigate to 192.168.0.100 - this goes to the Raspberry Pi's configuration page.
• Login using "root" as the username.
• Navigate to Network -> Interfaces -> WAN -> Edit.
• Change protocol to DHCP and click "Save & Apply".
• Using a browser, navigate to your router and find the IP it has assigned the Raspberry Pi and navigate to that IP.
• Navigate to the page Status -> Miner Configuration. Enter your pool information in the below format.
• Navigate to the page "Miner Status" to check mining has started.
• You can then change your router subnet back to whatever you are used to using.

Alternative Subnet Change:

• Unplug your computer from all internet sources.
• Plug in an ethernet cable from the Raspberry Pi to your computer.
• Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings.
• Right click on your ethernet adapter -> Properties.
• Click on "Internet Protocol Version 4" and click properties.
• Select "Use the following IP address" and enter the following:
• IP Address: 192.168.0.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.0.100.
• Plug in an ethernet cable from the Raspberry Pi to you router.
• Restart the configuration instructions as above.

Hello all,

Canaan Creative has employed me to help liaise with the community and later provide technical support. They have done this in order to help provide:

1) timely technical support
2) provide better feedback (if I don't know, I can find out from the people within CC who will)
3) provide product and sales input from you guys directly into the company. If something is going wrong, YOU can fix it
4) provide native English press releases.

This is a paid position, however it will in no way affect my independence or freedom in being critical towards Canaan Creative outside of this thread. My contract specifically stipulates:


This means I won't sit here and reply to every post saying CC is a scam, don't buy from CC etc etc, in this thread. It does NOT prohibit me from saying that in my own threads, if that is what I believe. It also has absolutely no impact on their rating in the Manufacturer trustworthiness thread.