It would have been nice if you had said what your solution was.

Yet another error message to add to the list:
warning: job finished, 0:0:Pitcairn is idle.

they sometime come together and sometimes it is just one of those, it can be anyone of those as far as I have noticed.
Does anyone recognize any of these problems? I could really use some help, I have not been able to find much online about these error messages and no possible solutions at all.
Maybe my pc and I just aren't cut out for bitminingXD
Could anyone maybe post the error messages to the main deepbit board, I can still not post there. Is there any kind of main tech support threat for this kind of thing?

I would als like to add the speed just went down with another message:
RPCError: You are reconnecting to long poll too fast

I own a 7850 that is not overclocked. the temperatue of the GPU while mining with full GPU load is steady around 74-77. This should not be a problem as other people overclock there 7850 and push and keep it steady at 85+. When I manually max my fan speed at 100% the temperatue won't even go above 70 degree's. So it seems very unlikely that the GPU temperature is the problem.

Does anyone have any ideas??

It is permanent as in, it will stay that low until i restart again. I don't think there is a specific interfal, once it had been running for an hour or so until it slowed down again.
I check the concole every time to see what happend and it says 95% of the time:
"long poll: new block" with a code after that.
It has also said "long poll IO error"
and it says IO errors - 1, tolerance 2 sometime when i restart it.
the other message that seems to slow it down is:
ADL_Adapter_ID_Get failed, cutoff temperature disabled for 0:0:Pitcairn
which has only happened a couple of times.

the hashing speed does not rise agains until i manually stop and restart the mining.

There are a couple of things that seem to slow my speed down from +-300 Mhash/s to only 300 Khash/s.
The decrease is usually when i get the messages:

 "long poll: new block...."
and

ADL_Adapter_ID_Get failed, cutoff temperature disabled for 0:0:Pitcairn

I don't know why my speed drops after a new block has been found but it does, and when I stop/start for a sec it will be back to normal.
I don't even begin to grasp what the whole ADL Adapter thingy might mean. Can it be my PSU isn't sufficient anough?

There are a couple of things that seem to slow my speed down from +-300 Mhash/s to only 300 Khash/s.
The decrease is usually when i get the messages:

 "long poll: new block...."
and

ADL_Adapter_ID_Get failed, cutoff temperature disabled for 0:0:Pitcairn

I don't know why my speed drops after a new block has been found but it does, and when I stop/start for a sec it will be back to normal.
I don't even begin to grasp what the whole ADL Adapter thingy might mean. Can it be my PSU isn't sufficient anough?

There are a couple of things that seem to slow my speed down from +-300 Mhash/s to only 300 Khash/s.
The decrease is usually when i get the messages:

 "long poll: new block...."
and

ADL_Adapter_ID_Get failed, cutoff temperature disabled for 0:0:Pitcairn

I don't know why my speed drops after a new block has been found but it does, and when I stop/start for a sec it will be back to normal.
I don't even begin to grasp what the whole ADL Adapter thingy might mean. Can it be my PSU isn't sufficient anough?

Hey there,

I'm totaly new at the whole mining thing. I considered it once, but it did not seem very    
lucrative. I now read comments from 2 years ago saying a newcomer tried it out and made 10 BTC in a couple of days.
Well... fuck me for not jumping on board then cause with the prices going trough the roof.

So I decided to try it out now, maybe with the high-value of BTC's I might even make some money.
I've set up my wallet, GUIMiner and deepbit and everything seems to be worken, but.....

There are a couple of things that seem to slow my speed down from +-300 Mhash/s to only 300 Khash/s.
The decrease is usually when i get the messages:

 "long poll: new block...."
and

ADL_Adapter_ID_Get failed, cutoff temperature disabled for 0:0:Pitcairn

I don't know why my speed drops after a new block has been found but it does, and when I stop/start for a sec it will be back to normal.
I don't even begin to grasp what the whole ADL Adapter thingy might mean. Can it be my PSU isn't sufficient anough?

Any help and or advise would be much appreciated.
DeepBit has pulled me true the start up, I hope you guys can help me get rid of the little problems aswell;)