The following timings can be set in the GUI.

RCAb, RCPb, RPAb, and RPPb.

They also show up using the cli

amdmemtweak --current

How can you set them using the CLI?

I have a question regarding the voltage options in a mixed rig.

I have a rig with nvidia and amd cards.

"-cvddc   set target GPU core voltage, multiplied by 1000. For example, "-cvddc 1050" means 1.05V. You can also specify values for every card, for example "-cvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
   Note: for NVIDIA cards this option is not supported.

-mvddc   set target GPU memory voltage, multiplied by 1000. For example, "-mvddc 1050" means 1.05V. You can also specify values for every card, for example "-mvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
   Note: for NVIDIA cards this option is not supported."

So, I understand I cannot use -cvddc and -mvddc for voltage control on the nvidia cards, but is there a way to use them on my AMD cards without running 2 instances of the miner?  (I use MSI Afterburner to control the power on the Nvidia cards)

Thanks in advance

I am using Windows 10.  Previously using Claymore's latest miner 11.6 and the flag -eres 0 worked for fixing this.  I have tried updating to 11.7 with -eres 0 and it does not solve the issue any longer.

Not exactly though.  If his problem is similar to mine, the search function helped defeat this issue previous and now it is back.

I have this issue as well again today

I did check the twitter, but the proof is in the pudding.

They supposedly moved to the right blockchain hours ago, but BALANCE and PAID on their website STILL show zero.   Even if they were going to reimburse for the time spent on the wrong chain, their site should be showing pending balances now.

Was wondering if someone could help me out with 2 strange problems.  (Using Claymore 10.0 but the same issue has carried over through 9.5 and 9.7)

1.  No matter what my config.txt file is, the miner reports it has trouble parsing line #14.

I have rearranged the lines in the file, added lines, even comment out all the flags.  Same parsing error.

2.  The clock I set for core and memory do not "take" until it is run a second time after reboot.  If I reboot my system, and then run Claymore's miner, it will mine at its original clock rates, not those I have specified in the config.txt file.  Upon the 2nd run after reboot (and all subsequent runs) it does run with the correct clocks.

Thanks in advance.Was wondering if someone could help me out with 2 strange problems.  (Using Claymore 10.0 but the same issue has carried over through 9.5 and 9.7)

1.  No matter what my config.txt file is, the miner reports it has trouble parsing line #14.

I have rearranged the lines in the file, added lines, even comment out all the flags.  Same parsing error.

2.  The clock I set for core and memory do not "take" until it is run a second time after reboot.  If I reboot my system, and then run Claymore's miner, it will mine at its original clock rates, not those I have specified in the config.txt file.  Upon the 2nd run after reboot (and all subsequent runs) it does run with the correct clocks.

Thanks in advance.

They are not supported for NVidia cards, but they also support a card by card setup.  Therefore can you setup only the AMD cards, leaving the Nvidia cards as they are?

Afterburner will not set the voltages.

In a mixed rig (AMD and NVidia) how does one use the mem and core clock and volt flags.

Namely since it is not supported for Nvidia, how do you specify the values for the AMD cards?  Can any value be used in the Nvidia spots and be ignored?  Can one not use the flags in this situation?

To reduce variables I placed the two ASUS cards in the PCI-e slots on the mobo.  Tested it and had no problems.  This ruled out any bad cards.

Placed the cards BOTH on risers (no card on the mobo directly) and it failed within a few minutes of load.   Bad risers.

Anyone have a suggestion on good quality risers?

Newbie here.  Any help appreciated.

Setting up my rig.  This worked yesterday for a 36 hour run

      - MSI Z170A Gaming M7
      - 1x Sapphire Nitro (no plus) 8G RX480  (rookie mistake slower memory)
      - 1x Asus Dual RX 480 8G
          BOTH GPUs mounted on mobo
      - windows 7 64bit
      - Claymore v 9.3
      - crimson v 17.4.3
      - firewall off


My config:

-epool USEast.Alpereum.ch:3002
-ewal (xxxxx)
-epsw x
-mode 1
-ethi 16
-tt 85
-asm 0
-wd 2
-benchmark
-fanmin 70

Ran great.  Just going for stability, not speed yet.  Both cards hashed around 24-25Mh/s

------------
Today the risers arrived. (MintCell v006)

Moved the the ASUS DUAL card to the riser.  Added a second ASUS DUAL card with riser.  Sapphire remained on mobo in PCIe slot.

Started Claymore.  All cards hashing about 24-25Mh/s

After 3 minutes of mining ATI driver crash.  One mining card stops mining.

Reboot.  Same behavior.

---------
Read the forums.  Tried to back off to the suggested v15.2 driver, but it would not run with my RX 480.  Settled on driver 16.11.5

Same behavior.

----------

Ran the rig with the Sapphire mounted in case and only 1 ASUS on riser.   This was stable.

-----------

Any ideas?  I have swapped risers to no avail.  I can run 2 cards stable, but adding the third causes a crash a few minutes into mining.

At the time of the crashes no cards are running super hot.  (60-70 C)

Thanks