Search content
Sort by
Showing 20 of 371 results by achtung082
Re: Official FutureBit Apollo BTC Software/Image and Support thread
Have had 4 batch 1 units running on a power-one psu for some time, still on v0.3.0 and do seem to be more stable when using a USB hub. They seem to need a reboot or even better a power reset every 1-2 weeks without a USB hub.
Re: Official FutureBit Apollo BTC Software/Image and Support thread
Have a couple issues:
1) GUI does not refresh and display miner status correctly. How does one force the interface to refresh /reload from ssh or monitor the miner status from ssh.
2) No disable node option. How can the node be disabled so that is does not run on power up or reboot. Clicking stop is possible but how can it be disabled completely?
3) Miner randomly disconnect from pool. The miner boards randomly disconnect, the red led still flashes as if it is mining, but the miner is cold and does not show as being connected to the pool. The GUI does not refresh so there is no way to check the state in the GUI.
Re: Official FutureBit Apollo BTC Software/Image and Support thread
Have two issues.
1) Can only set one pool.
2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.
Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.
Any advice would be greatly appreciated.
1) Can only set one pool.
2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.
Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.
Any advice would be greatly appreciated.
Start them up and leave them be for 10-15 minutes. They will start up eventually. As long as you see the front LED start flashing slowly it will show up in the dashboard.
Solid RED led after startup and one flashing green led on the board, on the last unit that will not run, seems to be bricked.
If I connect this unit to the full unit/controller nothing loads on the miner page and the page defaults back to original default page, shows slushpool, no stats load.
Ok if it does not start flashing at all when you do stop or restart on the miner dashboard then that means the system does not see it at all. Shoot an email to us by replying to your order email and well go over some other troubleshooting steps.
Will do, was just writing you a PM with more info, but will email.
Re: Official FutureBit Apollo BTC Software/Image and Support thread
Have two issues.
1) Can only set one pool.
2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.
Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.
Any advice would be greatly appreciated.
1) Can only set one pool.
2) All but 1 of my units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function with no unit connected and shows the default config with default pool.
Update: I was able to now get some units working again by connecting each one to the USB 1 port and booting the units individually. All but 1 of the units are now working. I will try connect the still bad unit to a PI and run it on its own.
Any advice would be greatly appreciated.
Start them up and leave them be for 10-15 minutes. They will start up eventually. As long as you see the front LED start flashing slowly it will show up in the dashboard.
Solid RED.
Re: Official FutureBit Apollo BTC Software/Image and Support thread
Have two issues.
1) Can only set one pool.
2) All but 3 units have stopped working after trying to change the the miner settings. I have tried setting eco, balanced and even advanced with power from min to 45%. Only One unit will work when I make these changes but the rest will not function at all. Even the main controller will not function and show the default config with default pool.
Any advice would be greatly appreciated.
Price on the msi's?
The GPU's are all sold.