gotcha!

Yeah, I'm currently selling of my BE's to use the $$ for U1s.

hey cs2000...

I'm using your instructions from several pages back.... thanks for the download.

Will this work with the older USB Erupters as well?  I have a mixed setup (49 port hub, gradually replacing old erupters with AntMiner U1s).

I did a test with 1 erupter and I don't think it was hashing with it.

Happy Holidays and Holinights!

18DunqnRWAoufMNzdbfGd5WSoaoJ9jyteR

I had a faulty board and it would look like this ^ for a little bit before the entire cube would cease to function (usually 1 to 6 hours later).
After I took out that board, it runs non-stop with no issues.  I don't know if you have the same issue that I did... but some food for thought I guess.

I'm running my stratum proxy on a machine that occasionally (like once every few weeks) locks up and restarts.

I am using bitminter to mine right now and would like to use their GETWORK option as a backup... would this be possible? Their address is: http://mint.bitminter.com:8332 (GBT or getwork)

I tried this to only test out the connection-


EDIT:
Nevermind... it worked.  Just took a few minutes to start up.

I'm going to set my pools like this:
StratumProxy,Direct... so that if my proxy fails, it will go directly to their getwork server.

I found the faulty board.  After putting in each board one at a time, I finally found one that crashed all the others.  I made sure it was the board by testing on different slots as well.  I pulled the bad board and the cube has been running at 28 gh/s all night with no issues.

I'm doing this now. Thanks for the suggestion.  So far, 2 boards running with no problems.  I'm adding a new board every 2 hours.  I did notice when I took the boards out that a few of them had loose heat sinks.  Hopefully tightening them will solve all my issues!

I have an all X problem which I'm assuming is power related.

At first it was hashing away nicely for about 8 hours... then it stopped.  After restarting, and then doing a full factory reset.... it will only run for about 1 hr before stopping.

power supply is a new Corsair CX750M with nothing else plugged in.  Before I ran the cube on it... it was powering a 49 port USB erupter setup with no issues.  :/

I calculate my fiat debt in bitcoins.

Right now I'm 11 bitcoins away from being debt free... I am saving bitcoins as fast as possible until I can pay it off all at once.  Current projection is it will take me about 2 years from now AT THIS PRICE. 

So the cool thing is that if the price goes up, my timeline goes down! 

I can almost taste it! no more owing doctor bills!

You are right though... If you were to owe somebody in BTC and the price jumped, it would be tough/impossible to pay it back...... however, due to volatility, the price could crash and you could pay it off sooner, right?

the faucet works great!

I tried it out yesterday and the process was easy to use and understand.

13gxJJagTVnYJRqPrrvePFW5DLUiwN3er4

Mine is no longer available.  It can be removed from the order book.

Thanks!

bump.

would consider offers too

sorry to make a change same day.. but I would like the order book updated:

Selling 10 at .185 per....   total: 1.85 BTC

Offer 0.56 BTC

I will cover the cost of Escrow.  USA only please!

please add me to the order book

selling 5  for 1 BTC  (this is .2 each)

Must use Escrow with pouncer or maxmint.

The advisor should have given you 3 addresses to send to.

Please check this screenshot.. did yours look like this?

http://imgur.com/28i4B7H

here is a screenshot:
http://imgur.com/J2J5yiN

Hi Haightst,

This thread is for buying and selling MasterCoin.  I don't think you are doing either of these things. 

Can you please take your general comments and musings to the overall MasterCoin project development thread?  That thread is here:
https://bitcointalk.org/index.php?topic=265488.0

I think you would be more apt to getting the discussion you crave if you posted there.  At the moment, your posts just add to the general noise and make it more difficult for us to pick out legit buyers/sellers.

Thanks,
- everyone here

I'm having an issue sending using the Mastercoin-explorer simple send.
I created a new thread, but I think maybe it's better suited here.

I'm trying to practice using TEST mastercoins.

Here is what I did:

• First I opened my QT client and went to the console.
• I validated my from address that contains mastercoins and got my public key.
• Then I entered the info into the mastercoin explorer simple send form (using TEST mastercoins as the currency).  My "to" address is just an address that I have in my QT wallet... so I'm trying to send to myself.
• I followed the instructions and ran the raw transaction.  This is what I come up with:
  f039df74dc453ea138d03ca463bd60ab947a27a5c62002c6e3404ba8222a77cc

The transaction appears on the blockchain... but it doesn't appear in the mastercoin-explorer. 

What did I do wrong?

My next step in troubleshooting is to try again, but this time I have sent all my BTC to the address I'm sending msc from.  Not sure if that matters or not but I figure it's worth a try.