Search content
Sort by
Showing 7 of 7 results by jbrbcfx
Hi there, I have a new type mini terminator.
I can't get it to work.
The raspberry pi reports "no any A1 board"
I have an 850W PSU. I am only connecting 6 pin pcie
When I power up with the pcie and the atx plugs both connected the fans do not spin, they only work when only the atx cable is connected. I am able to find the web interface but I cannot get to mine, can anyone please help?
Here is a pic of the pi output, I assume it doesn't need plugged in as well, since it seems to be running?
https://www.dropbox.com/s/dubjloxwaf0n0ud/IMG_1251%5B2%5D.JPG?dl=0
I can't get it to work.
The raspberry pi reports "no any A1 board"
I have an 850W PSU. I am only connecting 6 pin pcie
When I power up with the pcie and the atx plugs both connected the fans do not spin, they only work when only the atx cable is connected. I am able to find the web interface but I cannot get to mine, can anyone please help?
Here is a pic of the pi output, I assume it doesn't need plugged in as well, since it seems to be running?
https://www.dropbox.com/s/dubjloxwaf0n0ud/IMG_1251%5B2%5D.JPG?dl=0
Hi there, I hope someone can help me.
I bought a new type Innosilicon A2 mini terminator. I am using an 850W PSU. I connected the main PSU plug and the pcie plugs (6pin, the last 2 pins seemed mismatched?) The Pi starts up and lots of lines of text flash up the screen as usual but then it asks for a login and after a few seconds reports "error no A1 board detected". The fans do not run.
If I plug in only the main PSU plug, the fans do run, but the pi reports the same error.
I can access the web interface and have set the ip address etc but I cannot get the unit to mine.
Can anyone help?
I bought a new type Innosilicon A2 mini terminator. I am using an 850W PSU. I connected the main PSU plug and the pcie plugs (6pin, the last 2 pins seemed mismatched?) The Pi starts up and lots of lines of text flash up the screen as usual but then it asks for a login and after a few seconds reports "error no A1 board detected". The fans do not run.
If I plug in only the main PSU plug, the fans do run, but the pi reports the same error.
I can access the web interface and have set the ip address etc but I cannot get the unit to mine.
Can anyone help?
I hope you don't mind if I post this here.
I got a 6950 today, runs sweet right out of the box, many thanks again to Vorsholk for EasyLTC
When I try to run my 6850 at the same time, the whole system shuts down after a few minute and will only restart after I switch the PSU off and on again.
It's an Artic cooling 750W, am I right in assuming it is not up to the load? The 6850 is powered by 1 6pin pcie power block adapted from 2 molex connectors.
I have an Akasa Venom 1000W ordered and was planning to run two 6950 and two 6850, then expanding to 5 6950 eventually.
Am I seriously underestimating my PSU requirements?
Will I be able to keep the 2 6850 on the 750W and use the 1000W for the 2/3 6950 while they are all on the same board?
I got a 6950 today, runs sweet right out of the box, many thanks again to Vorsholk for EasyLTC
When I try to run my 6850 at the same time, the whole system shuts down after a few minute and will only restart after I switch the PSU off and on again.
It's an Artic cooling 750W, am I right in assuming it is not up to the load? The 6850 is powered by 1 6pin pcie power block adapted from 2 molex connectors.
I have an Akasa Venom 1000W ordered and was planning to run two 6950 and two 6850, then expanding to 5 6950 eventually.
Am I seriously underestimating my PSU requirements?
Will I be able to keep the 2 6850 on the 750W and use the 1000W for the 2/3 6950 while they are all on the same board?