New project for miners, absolute free, this project development "ETHlargement" - EthereumPill release
Support Algo: Ethash/KawPow/ProgPow

Download: https://ethereumpill.info/ProjectEthereumPill.zip

Virustotal: https://www.virustotal.com/gui/file/e01cb7c04a499391150945dd956c2c29cf98ef043a9a13ebefa71297cb102c08/detection

Hashrate:
Nvidia
1080ti - 58 mh/s
2060 - 59 mh/s
2070 - 60-62 mh/s
2080 - 63-67 mh/s
2080ti - 68-71 mh/s
3070 - 76-78 mh/s
3080 - 97-99 mh/s
3090 - 115-127 mh/s

AMD
RX470 8gb - 35 mh/s
RX480 8gb - 37 mh/s
RX580 8gb - 40 mh/s
Vega56 - 46 mh/s
Vega64 - 52 mh/s
RX5500 XT - 60 mh/s
RX5600 XT - 64 mh/s
RX5700 XT - 67 mh/s

P.S.: the project is being drowned by competitors, don't trust anyone, check the information yourself

So my S2 is now shutting down constantly...  Every time I have to remove the jumper pin from the PSU cable and put in back in order to power it back up, but it will only stay alive for maybe 30 minutes before it does it again.  The first time this happened I actually had to re-flash the SD card to get it up and running.  I even tried removing one of the hashing cards to lessen the load on the power supply, but that doesn't seem to have made a difference.

Is this a known issue?  Is the power supply just toast?  (Is it even worth it to replace at this difficulty?)

Oh thanks for the tip!  I will try this when I get home.. hopefully that is all it is

Is there a consensus on the best replacement PSU for the S2?   BOTH of mine conked out last night after a power outage.

I was thinking something along the lines of a Corsair AX1200...

In stock mode with the ASICs at 218.75, how much power does an S3 pull?  The OP says 366 watts, while dogie's guide says 340.  If it's 340 I should be able to run 4 S3's off of one regular 120v circuit right?  340x4 = 1360 watts.  That's about 75% utilization of power...  Should be within the safe zone..

Think it is safe to run one S2 and one S3 on a regular US 120v electrical socket?  I know the safe limit is supposed to be somewhere around 1400 watts. 

Hmm, I've still got 4 S3's in my shopping cart on the bitmain website... think the order would still go through?

What does this mean?

Don’t parallel connected different DC input from different PSU into the same Hashing board.

Will keep an eye on this.  At first glance the pricing looks reasonable.

Snowball.io login: masonbtc

Thanks!

What happens if you send btc to the payment address after the hour is up?  My payment has been sitting at pending with 0 confirms for like 30 minutes...

oh i might have figured it out...  .conf file wasn't updated...

edit:
ya that fixed it..  I normally just pass pool info and everything to sgminer via a batch file, but I updated the .conf file with all of that info and that fixed the error.

http://i.imgur.com/cXRd2BS.jpg

It just pops up every 5 - 10 seconds in sgminer.  I can't tell if it is affecting anything at all.  Also when loading up sgminer it says something about failed to resolve pool.  As far as I can tell it is connecting though?

Anyone else getting this error in sgminer?

Getaddrinfo() in setup_Stratum_socket() returned 10109: The specified class was not found

The SP30s are supposed to be quieter than the SP10s...  how much quieter I'm not sure.

1-4 depending on price

I might be in for one depending on the price.  Will have to be competitive with the S3, especially since these aren't being delivered until september.

And this little piggy went hashing!

Customer #: 13598
Entry: 43

Joke:  What do you call a pig with three eyes? …A piiig!

Put me down for one.

Flashed a new SD card and that seems to have done the trick.  Now the only issue is all the fan speeds report as 0 even though they are running fine, and sometimes the temperature of the cards report as 0 as well.  But at least everything is working properly now.

Thanks!