Ninjastic
Search content
Sort by
Showing 6 of 6 results by raashaad2010
Post
Topic
Board Mining (Altcoins)
Re: problem inno3d p104-100
by
raashaad2010
on 01/06/2018, 12:48:37 UTC
Quote from: shibob on June 01, 2018, 02:29:29 AM
Quote from: androstan1234 on May 31, 2018, 03:54:03 PM
Quote from: raashaad2010 on May 31, 2018, 10:36:42 AM
Quote from: androstan1234 on May 30, 2018, 11:25:12 PM
2000W!?
yes

That's way, way too high.  You need to lower power limit, as others itt have suggested.

That's not the power consumption mate, it's all about the power supply. Actually 6 * P104-100 consume not that much power, as far as I know the TDP is about 180W - 225W, depend on which manufacturer. For me I'm using 1600W PSU for the rig with: 6 P104-100 + 2 P106-100, power limit was set at 80%, so far so good.
Now the machine promises Zec
 Is there a risk when lifting the power
cor 180
mom 125
power limit 180
59c
Post
Topic
Board Mining (Altcoins)
Re: problem inno3d p104-100
by
raashaad2010
on 31/05/2018, 10:36:42 UTC
Quote from: androstan1234 on May 30, 2018, 11:25:12 PM
2000W!?
yes
Post
Topic
Board Mining (Altcoins)
Re: problem inno3d p104-100
by
raashaad2010
on 30/05/2018, 22:31:59 UTC
]

Hi mate, your core OC is too high, and 530 sol/s, seem like you run it at 100% power limit, It's a bit too much. For me, I always set power limit at 80% only.
You could test it at stock setting first. Then step-by-step OC with higher core. I mined with P104-100 as well, so far so good, for your interest, please check my tests in following thread. By the way, I think P104-100 could do better on mining ETH rather than mining ZEC.

https://bitcointalk.org/index.php?topic=2677496
[/quote]
Please what are the settings of eth
Post
Topic
Board Mining (Altcoins)
Re: problem inno3d p104-100
by
raashaad2010
on 30/05/2018, 13:23:06 UTC
Quote from: jmigdlc99 on May 30, 2018, 12:31:13 PM
Quote from: raashaad2010 on May 30, 2018, 11:54:47 AM
Quote from: papi92 on May 30, 2018, 07:00:32 AM
Try to decrease core and mem clock.

https://f.top4top.net/p_880oz27j0.jpg

You actually have it running at 150% power limit. That is too much and probably a good way to overload your GPU. Most people run their GPUs at the low value of 65%.

With regards to coreclock, you also have it set to the MAX value. Bad. Thats probably why your miner crashes resulting in the decrease in hashrate. Your mem clock seems to be the only sane value on your config and you could probably increase it slowly. Make sure to do your research before overclocking else you might end up destroying your hardware.
What do you suggest to be values
Post
Topic
Board Mining (Altcoins)
Re: problem inno3d p104-100
by
raashaad2010
on 30/05/2018, 11:54:47 UTC
Quote from: papi92 on May 30, 2018, 07:00:32 AM
Try to decrease core and mem clock.

https://f.top4top.net/p_880oz27j0.jpg
Post
Topic
Board Mining (Altcoins)
problem inno3d p104-100
by
raashaad2010
on 30/05/2018, 01:28:40 UTC
hi i have 6 card inno3d p104-100
mining zcash
simplemining
power 2000 w
motherboard: - colourful
But there is a problem which is a low speed device ... with a start. The operating speed reaches 3200 sol but after an hour or less suddenly the speed drops to 250 sol and I do not know why?

https://e.top4top.net/p_8798hyui0.png

https://f.top4top.net/p_879bek4i0.png