Search content
Sort by
Showing 20 of 28 results by tornado_blade
It is extremely unlikely that you have three simultaneous pic failures. It's more likely that the 3.3V power that is sourced by the control board to power the pic has been lost. To put it another way it is the control board that powers the pic and not any circuitry intrinsic to that particular hashboard.
Are you getting 3.3 volts on the hashboard data connector? Also, as a matter of best practices and expedience post your kernel log in a "#-button-above" sequence.
Cheers,
J
thanks a lotAre you getting 3.3 volts on the hashboard data connector? Also, as a matter of best practices and expedience post your kernel log in a "#-button-above" sequence.
Cheers,
J
but i fixed control board and all hash boards by change pic and eEprom and failure asics and one of them lost mp ic and some R in temp sensor line.
now miner work with 80th.
Re: What is the going rate for BM1397AG Asic Chips for S17+
Getting Quoted around $25 per chip with MOQ of 10 from alibaba.
Is this a reasonable price?
Any other recommended outlets?
you can buy failure hash board s17+ or t17+ and scrap it.Is this a reasonable price?
Any other recommended outlets?
but be careful that hash board Intact and most of heat sinks be on chip.
by this way you have more than 20 chip and other parts of hash board with lower price.
Hi there:
Could anyone explain me how temperature sensors on S19Pro work? What [picTem] and [ChipTem] show? These columns show two data, what do they exactly mean?
The old miner S9 showed inlet and outlet temp. It was clear.
S19Pro software is not so clear... I would say horrible. And mobile version is absolutely unreadable.
Moreover, manual says nothing about this issue.
I hope the picture will be added below:
Thanks for any responses.
http://blob:file:///03657607-c180-415e-a75b-ed19d63ef2df
Could anyone explain me how temperature sensors on S19Pro work? What [picTem] and [ChipTem] show? These columns show two data, what do they exactly mean?
The old miner S9 showed inlet and outlet temp. It was clear.
S19Pro software is not so clear... I would say horrible. And mobile version is absolutely unreadable.
Moreover, manual says nothing about this issue.
I hope the picture will be added below:
Thanks for any responses.
http://blob:file:///03657607-c180-415e-a75b-ed19d63ef2df
hi
you need this sensor in corner of hashboard.
https://www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=393
Hi!
I use an antminer S17 at home. Yesterday, suddenly, mining stopped. Since this moment I cannot reach the miner UI, also ping is not possible. The network itself works, leds for network are on. Any idea, what I could do? A reset changed nothing.
Thanks
are your control board leds blinking or on?I use an antminer S17 at home. Yesterday, suddenly, mining stopped. Since this moment I cannot reach the miner UI, also ping is not possible. The network itself works, leds for network are on. Any idea, what I could do? A reset changed nothing.
Thanks
Hello,
I purchased two used Antminer S9's with braiins os+. One of them I was able to setup fine, and it is hashing at up to 14.5 TH. For the other one, I am able to see it on my network and log into the Braiins web interface, but it is not hashing, and doesn't show any temperature readings (it does show the fan readings). For the one that doesn't work, it has the red "fault" light lit up solid. Also on the one that doesn't work, the red light is lit up on only one of the three chip boards. I tried swapping power supplies on the two units, and got the same result. Here is an excerpt of the kernel log where I think there are some possible issues ("no such file or directory"). Does anyone know what is wrong? I have a call in to the seller who has a two week warranty, but hoping to figure it out. Thanks in advance.
can you share picture of your pool address?I purchased two used Antminer S9's with braiins os+. One of them I was able to setup fine, and it is hashing at up to 14.5 TH. For the other one, I am able to see it on my network and log into the Braiins web interface, but it is not hashing, and doesn't show any temperature readings (it does show the fan readings). For the one that doesn't work, it has the red "fault" light lit up solid. Also on the one that doesn't work, the red light is lit up on only one of the three chip boards. I tried swapping power supplies on the two units, and got the same result. Here is an excerpt of the kernel log where I think there are some possible issues ("no such file or directory"). Does anyone know what is wrong? I have a call in to the seller who has a two week warranty, but hoping to figure it out. Thanks in advance.
Code:
open stratum channel
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Caused by:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 0: Error while handling response for stratum open channel: Header { is_channel_message: false, extension_type: 0, msg_type: 18, msg_length: None }
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 1: Open channel error: Not authorized
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Apr 30 22:33:33.232 WARN bosminer::client::stratum_v2: user:stratum+tcp://32H4BVgYFXd9oeHPGjkFR36tRufug3JCPT.09@solo.ckpool.org: Cannot open stratum channel
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Caused by:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 0: Error while handling response for stratum open channel: Header { is_channel_message: false, extension_type: 0, msg_type: 18, msg_length: None }
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 1: Open channel error: Not authorized
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Caused by:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 0: Error while handling response for stratum open channel: Header { is_channel_message: false, extension_type: 0, msg_type: 18, msg_length: None }
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 1: Open channel error: Not authorized
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Apr 30 22:33:33.232 WARN bosminer::client::stratum_v2: user:stratum+tcp://32H4BVgYFXd9oeHPGjkFR36tRufug3JCPT.09@solo.ckpool.org: Cannot open stratum channel
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: Caused by:
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 0: Error while handling response for stratum open channel: Header { is_channel_message: false, extension_type: 0, msg_type: 18, msg_length: None }
Sat Apr 30 22:33:33 2022 daemon.err bosminer[1555]: 1: Open channel error: Not authorized
Re: Looking for Antminer S19 90T firmware (or Antminer S20 firmware?)
2021-05-10 20:35:25 ERROR_SOC_INIT: soc init failed!
hi first flash all hashboards eEprom with code editor then think for other ways.
I noticed that the PIC LOST error can appear when the ribbon connection cable is bad, try to clean this, if it does not work you will actually have to flash the PIC with pickit
that is correct.but my hash boards eeprom and pic exploded.
need to replace and reflash each one.
Hello everyone I just bought an asic T9+ after configuring it the hashrate remained frozen at 0 and the same for the pools could someone help me?
thank you in advance for your answer !
https://imgur.com/a/3lzcJGR
hithank you in advance for your answer !
https://imgur.com/a/3lzcJGR
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J2] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J3] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J4] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J9] has 18 asic
[b]driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J10] has 0 asic[/b]
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J2] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J3] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J4] has 18 asic
driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J9] has 18 asic
[b]driver-btm-c5.c:11832:T9_18_getASICnum: Chain[J10] has 0 asic[/b]
chain 10 need to repair.
Hello friends i am new at mining. One of my cards on my a1 suddently stopped hashing(seems 0mh). I reboot my machine and i only see three cards(chains). I saw the log file and i thin i detect the problem, but i cant understand what it really is.
First a problem with chain 1
chain1: power down
Apr 06 04:28:52 rockchip cgminer[286]: fan0 speed:5760, fan1 speed:5880
Apr 06 04:28:53 rockchip cgminer[286]: chain1: encore first mode
Apr 06 04:28:56 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:28:56 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:28:56 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:28:57 rockchip cgminer[286]: fan0 speed:5820, fan1 speed:5880
Apr 06 04:28:59 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:28:59 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:28:59 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:02 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:02 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:29:02 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:02 rockchip cgminer[286]: fan0 speed:5790, fan1 speed:5820
Apr 06 04:29:05 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:05 rockchip cgminer[286]: spi_cmd_reset poll fail !
.
.what is first and second mode?
.
chain1: encore second mode
Apr 06 04:29:17 rockchip cgminer[286]: fan0 speed:5790, fan1 speed:5820
Apr 06 04:29:21 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:21 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:29:21 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:22 rockchip cgminer[286]: fan0 speed:5850, fan1 speed:5880
Apr 06 04:29:24 rockchip cgminer[286]: 1: detected 72 chips
Apr 06 04:29:24 rockchip cgminer[286]: collect core success
Apr 06 04:29:24 rockchip cgminer[286]: chain1: pre init OK, retries:1
.
.and at the same session problem but with chain 3(only one card is off)
.first 54 ppls set ok
Apr 06 05:39:16 rockchip cgminer[292]: Chain 3 VID 0 voltage 410.6
Apr 06 05:39:16 rockchip cgminer[292]: Chain 3 unable to get above target voltage 425 by VID 0
Apr 06 05:39:16 rockchip cgminer[292]: B1 chain[3] set pll, start_pll:54, target_pll:120
Apr 06 05:39:16 rockchip cgminer[292]: T1 3 set default 54 PLL success
Apr 06 05:39:16 rockchip cgminer[292]: T1 3 set default 55 PLL success
.
.all between ppls are ok
.
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 91 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 92 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 93 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 94 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: Failed to set PLL Lv.95 on T1 3 in T1_SetT1PLLClock
Apr 06 05:39:21 rockchip cgminer[292]: set default PLL fail
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_write_reg0d poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.same error multiple times
.
Apr 06 05:39:21 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: chain3 find_chain_vid: start_vid = 0, target_volt = 407
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip1
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip2
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip70
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip71
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip72
Apr 06 05:39:21 rockchip cgminer[292]: Chain 3 VID 0 voltage nan
Apr 06 05:39:23 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.72 chips fails again
.
Apr 06 05:39:24 rockchip cgminer[292]: Chain 3 VID 0 voltage nan
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: fan0 speed:5790, fan1 speed:6240
Apr 06 05:39:25 rockchip cgminer[292]: chain_detect: chain: 0, n_chips: 0
Apr 06 05:39:26 rockchip cgminer[292]: Chain 0 Voltage information. Highest Vol:435, Average Vol:416, Lowest Vol:402
Apr 06 05:39:26 rockchip cgminer[292]: 0: found 72 chips with total 2304 active cores
Apr 06 05:39:27 rockchip cgminer[292]: Chain 0 Post Balance Voltage. Highest Vol:435.000000, Average Vol:416.000000, Lowest Vol:400.000000.
Apr 06 05:39:28 rockchip cgminer[292]: chain_detect: chain: 1, n_chips: 0
Apr 06 05:39:28 rockchip cgminer[292]: Chain 1 Voltage information. Highest Vol:438, Average Vol:419, Lowest Vol:397
Apr 06 05:39:29 rockchip cgminer[292]: 1: found 72 chips with total 2304 active cores
Apr 06 05:39:29 rockchip cgminer[292]: Chain 1 Post Balance Voltage. Highest Vol:438.000000, Average Vol:419.000000, Lowest Vol:397.000000.
Apr 06 05:39:29 rockchip cgminer[292]: fan0 speed:5880, fan1 speed:6210
Apr 06 05:39:30 rockchip cgminer[292]: chain_detect: chain: 2, n_chips: 0
Apr 06 05:39:31 rockchip cgminer[292]: Chain 2 Voltage information. Highest Vol:435, Average Vol:414, Lowest Vol:397
Apr 06 05:39:31 rockchip cgminer[292]: 2: found 72 chips with total 2304 active cores
Apr 06 05:39:32 rockchip cgminer[292]: Chain 2 Post Balance Voltage. Highest Vol:435.000000, Average Vol:414.000000, Lowest Vol:397.000000.
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 0 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 1 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 2 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: B1 detect finish
seems that chain 3 is dead but something wrong with chain 1? My miner its not new but second hand
hiFirst a problem with chain 1
chain1: power down
Apr 06 04:28:52 rockchip cgminer[286]: fan0 speed:5760, fan1 speed:5880
Apr 06 04:28:53 rockchip cgminer[286]: chain1: encore first mode
Apr 06 04:28:56 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:28:56 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:28:56 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:28:57 rockchip cgminer[286]: fan0 speed:5820, fan1 speed:5880
Apr 06 04:28:59 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:28:59 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:28:59 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:02 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:02 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:29:02 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:02 rockchip cgminer[286]: fan0 speed:5790, fan1 speed:5820
Apr 06 04:29:05 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:05 rockchip cgminer[286]: spi_cmd_reset poll fail !
.
.what is first and second mode?
.
chain1: encore second mode
Apr 06 04:29:17 rockchip cgminer[286]: fan0 speed:5790, fan1 speed:5820
Apr 06 04:29:21 rockchip cgminer[286]: dm_compat.c,5164: poll fail !
Apr 06 04:29:21 rockchip cgminer[286]: spi_cmd_reset poll fail !
Apr 06 04:29:21 rockchip cgminer[286]: failed to reset chain 1!,try again
Apr 06 04:29:22 rockchip cgminer[286]: fan0 speed:5850, fan1 speed:5880
Apr 06 04:29:24 rockchip cgminer[286]: 1: detected 72 chips
Apr 06 04:29:24 rockchip cgminer[286]: collect core success
Apr 06 04:29:24 rockchip cgminer[286]: chain1: pre init OK, retries:1
.
.and at the same session problem but with chain 3(only one card is off)
.first 54 ppls set ok
Apr 06 05:39:16 rockchip cgminer[292]: Chain 3 VID 0 voltage 410.6
Apr 06 05:39:16 rockchip cgminer[292]: Chain 3 unable to get above target voltage 425 by VID 0
Apr 06 05:39:16 rockchip cgminer[292]: B1 chain[3] set pll, start_pll:54, target_pll:120
Apr 06 05:39:16 rockchip cgminer[292]: T1 3 set default 54 PLL success
Apr 06 05:39:16 rockchip cgminer[292]: T1 3 set default 55 PLL success
.
.all between ppls are ok
.
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 91 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 92 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 93 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: T1 3 set default 94 PLL success
Apr 06 05:39:21 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: Failed to set PLL Lv.95 on T1 3 in T1_SetT1PLLClock
Apr 06 05:39:21 rockchip cgminer[292]: set default PLL fail
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_write_reg0d poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.same error multiple times
.
Apr 06 05:39:21 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: chain3 find_chain_vid: start_vid = 0, target_volt = 407
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip1
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip2
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip70
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip71
Apr 06 05:39:21 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:21 rockchip cgminer[292]: failed to read voltage for chain3 chip72
Apr 06 05:39:21 rockchip cgminer[292]: Chain 3 VID 0 voltage nan
Apr 06 05:39:23 rockchip cgminer[292]: spi_cmd_read_register poll fail !
.
.72 chips fails again
.
Apr 06 05:39:24 rockchip cgminer[292]: Chain 3 VID 0 voltage nan
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_read_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: dm_compat.c,5164: poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: spi_cmd_write_register poll fail !
Apr 06 05:39:24 rockchip cgminer[292]: fan0 speed:5790, fan1 speed:6240
Apr 06 05:39:25 rockchip cgminer[292]: chain_detect: chain: 0, n_chips: 0
Apr 06 05:39:26 rockchip cgminer[292]: Chain 0 Voltage information. Highest Vol:435, Average Vol:416, Lowest Vol:402
Apr 06 05:39:26 rockchip cgminer[292]: 0: found 72 chips with total 2304 active cores
Apr 06 05:39:27 rockchip cgminer[292]: Chain 0 Post Balance Voltage. Highest Vol:435.000000, Average Vol:416.000000, Lowest Vol:400.000000.
Apr 06 05:39:28 rockchip cgminer[292]: chain_detect: chain: 1, n_chips: 0
Apr 06 05:39:28 rockchip cgminer[292]: Chain 1 Voltage information. Highest Vol:438, Average Vol:419, Lowest Vol:397
Apr 06 05:39:29 rockchip cgminer[292]: 1: found 72 chips with total 2304 active cores
Apr 06 05:39:29 rockchip cgminer[292]: Chain 1 Post Balance Voltage. Highest Vol:438.000000, Average Vol:419.000000, Lowest Vol:397.000000.
Apr 06 05:39:29 rockchip cgminer[292]: fan0 speed:5880, fan1 speed:6210
Apr 06 05:39:30 rockchip cgminer[292]: chain_detect: chain: 2, n_chips: 0
Apr 06 05:39:31 rockchip cgminer[292]: Chain 2 Voltage information. Highest Vol:435, Average Vol:414, Lowest Vol:397
Apr 06 05:39:31 rockchip cgminer[292]: 2: found 72 chips with total 2304 active cores
Apr 06 05:39:32 rockchip cgminer[292]: Chain 2 Post Balance Voltage. Highest Vol:435.000000, Average Vol:414.000000, Lowest Vol:397.000000.
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 0 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 1 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: Detected the 2 B1 chain with 72 chips / 2304 cores
Apr 06 05:39:32 rockchip cgminer[292]: B1 detect finish
seems that chain 3 is dead but something wrong with chain 1? My miner its not new but second hand
check your psu and replace with another one.
maybe your psu is bad.
0 asic there might be a connection issue on this hashboard would you mind to try run all hashboard one by one?
Another thing that can cause this issue is a bad PSU, sometimes the PSU just can't handle 3 hash boards, an easy to troubleshoot both the wiring and the PSU in the same step would be to disconnect 1 working boards wires (PSU + data ribbon cables) and attaching them to the bad board.
that is correct.
but in this case find 0 asic. most probably first hashboard failure.
Hello everyone recently i have buy an antminer s9 but my i got a problem my hashrate is average 9th/s but before the hashrate is average 14th/s !
https://imgur.com/a/4MkvioR
thanks for your help everyone
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000013] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000294] ps7-ttc #0 at df804000, irq=43
[ 0.000595] Console: colour dummy device 80x30
[ 0.000624] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040197] pid_max: default: 32768 minimum: 301
[ 0.040405] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040425] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042582] CPU: Testing write buffer coherency: ok
[ 0.042893] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042950] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.043170] L310 cache controller enabled
[ 0.043190] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.120985] CPU1: Booted secondary processor
[ 0.210218] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210347] Brought up 2 CPUs
[ 0.210365] SMP: Total of 2 processors activated.
[ 0.210374] CPU: All CPU(s) started in SVC mode.
[ 0.211031] devtmpfs: initialized
[ 0.213463] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214648] regulator-dummy: no parameters
[ 0.222003] NET: Registered protocol family 16
[ 0.224271] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226530] cpuidle: using governor ladder
[ 0.226544] cpuidle: using governor menu
[ 0.233917] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235426] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235440] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235548] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.256893] bio: create slab <bio-0> at 0
[ 0.258286] vgaarb: loaded
[ 0.258970] SCSI subsystem initialized
[ 0.259858] usbcore: registered new interface driver usbfs
[ 0.260027] usbcore: registered new interface driver hub
[ 0.260378] usbcore: registered new device driver usb
[ 0.260909] media: Linux media interface: v0.10
[ 0.261098] Linux video capture interface: v2.00
[ 0.261384] pps_core: LinuxPPS API ver. 1 registered
[ 0.261395] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.261521] PTP clock support registered
[ 0.261889] EDAC MC: Ver: 3.0.0
[ 0.263074] Advanced Linux Sound Architecture Driver Initialized.
[ 0.265809] DMA-API: preallocated 4096 debug entries
[ 0.265822] DMA-API: debugging enabled by kernel config
[ 0.265890] Switched to clocksource arm_global_timer
[ 0.285679] NET: Registered protocol family 2
[ 0.286714] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.286771] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.286856] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.286902] TCP: reno registered
[ 0.286918] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.286946] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.287722] NET: Registered protocol family 1
[ 0.288237] RPC: Registered named UNIX socket transport module.
[ 0.288250] RPC: Registered udp transport module.
[ 0.288259] RPC: Registered tcp transport module.
[ 0.288267] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288279] PCI: CLS 0 bytes, default 64
[ 0.288705] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.290689] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.292721] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.292907] msgmni has been set to 967
[ 0.293678] io scheduler noop registered
[ 0.293691] io scheduler deadline registered
[ 0.293731] io scheduler cfq registered (default)
[ 0.304958] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.304979] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.428483] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.995797] console [ttyPS0] enabled
[ 1.000062] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.007694] [drm] Initialized drm 1.1.0 20060810
[ 1.024751] brd: module loaded
[ 1.034162] loop: module loaded
[ 1.043514] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.049340] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.057163] libphy: XEMACPS mii bus: probed
[ 1.061533] ------------- phy_id = 0x3625e62
[ 1.066448] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.075019] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.081857] ehci-pci: EHCI PCI platform driver
[ 1.089157] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.096005] usbcore: registered new interface driver usb-storage
[ 1.102823] mousedev: PS/2 mouse device common for all mice
[ 1.108930] i2c /dev entries driver
[ 1.115792] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.121305] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.127227] Xilinx Zynq CpuIdle Driver started
[ 1.132078] sdhci: Secure Digital Host Controller Interface driver
[ 1.138191] sdhci: Copyright(c) Pierre Ossman
[ 1.142508] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.149389] mmc0: no vqmmc regulator found
[ 1.153405] mmc0: no vmmc regulator found
[ 1.195912] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.204582] usbcore: registered new interface driver usbhid
[ 1.210084] usbhid: USB HID core driver
[ 1.214794] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221090] nand: Micron MT29F2G08ABAEAWP
[ 1.225058] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.230992] Bad block table found at page 131008, version 0x01
[ 1.237216] Bad block table found at page 130944, version 0x01
[ 1.243266] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249046] Creating 3 MTD partitions on "pl353-nand":
[ 1.254139] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.262186] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.269486] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.280204] TCP: cubic registered
[ 1.283440] NET: Registered protocol family 17
[ 1.288131] Registering SWP/SWPB emulation handler
[ 1.294006] regulator-dummy: disabling
[ 1.298319] UBI: attaching mtd1 to ubi0
[ 1.684981] UBI: scanning is finished
[ 1.696800] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.703855] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.710649] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.717328] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.724165] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.730175] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.737286] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1113221046
[ 1.746316] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.755513] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.755518] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.759431] ALSA device list:
[ 1.759434] No soundcards found.
[ 1.776369] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.906640] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.912570] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.921708] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.931587] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.936626] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[ 1.964552] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.990392] devtmpfs: mounted
[ 1.993496] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.126367] random: dd urandom read with 1 bits of entropy available
[ 3.735941]
[ 3.735941] bcm54xx_config_init
[ 4.805941]
[ 4.805941] bcm54xx_config_init
[ 20.806767] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 20.812860] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 35.585636] In axi fpga driver!
[ 35.588722] request_mem_region OK!
[ 35.592098] AXI fpga dev virtual address is 0xdf9fe000
[ 35.597221] *base_vir_addr = 0xc51e
[ 35.611846] In fpga mem driver!
[ 35.615134] request_mem_region OK!
[ 35.618767] fpga mem virtual address is 0xe2000000
[ 36.395915]
[ 36.395915] bcm54xx_config_init
[ 37.485938]
[ 37.485938] bcm54xx_config_init
[ 53.486765] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 53.492781] xemacps e000b000.ps7-ethernet: link up (100/FULL)
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 507486208
main.c:14031: Detect 512MB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6fda000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5dd3000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 817c142c68808814
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x000000e0
driver-bitmain.c:1946: Find hashboard on Chain[5]
driver-bitmain.c:1946: Find hashboard on Chain[6]
driver-bitmain.c:1946: Find hashboard on Chain[7]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[6] has freq in PIC and will jump over...
main.c:9103: Chain[6] has core num in PIC
main.c:9113: Chain[6] ASIC[14] has core num=3
main.c:9113: Chain[6] ASIC[16] has core num=4
main.c:9113: Chain[6] ASIC[26] has core num=1
main.c:9113: Chain[6] ASIC[29] has core num=1
main.c:9113: Chain[6] ASIC[31] has core num=1
main.c:9113: Chain[6] ASIC[59] has core num=1
main.c:9113: Chain[6] ASIC[61] has core num=1
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[7] has freq in PIC and will jump over...
main.c:9103: Chain[7] has core num in PIC
main.c:9113: Chain[7] ASIC[9] has core num=2
main.c:9113: Chain[7] ASIC[42] has core num=15
main.c:9113: Chain[7] ASIC[46] has core num=1
main.c:9113: Chain[7] ASIC[54] has core num=5
main.c:9113: Chain[7] ASIC[61] has core num=15
main.c:9113: Chain[7] ASIC[62] has core num=15
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9183: get PIC voltage=6 on chain[6], value=940
main.c:9183: get PIC voltage=6 on chain[7], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:9349: chain[6] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[6] temp chip I2C addr=0x98
main.c:9372: chain[6] has no middle temp, use special fix mode.
main.c:9349: chain[7] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[7] temp chip I2C addr=0x98
main.c:9372: chain[7] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 3
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 3, total chain num = 3
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found= 4754 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12292:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 817c142c68808814
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x0b 0x4a 0x09 0x4a 0x04 0x4a 0x0a 0x4a 0x00 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x01 0x4a 0x01 0x4a 0x0f 0x4a 0x0f 0x4a 0x0f 0x4a 0x0f 0x4a 0x05 0x4a 0x07 0x4a 0x23 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=870
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4b 0x00 0x4b 0x04 0x4b 0x0b 0x4b 0x00 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x01 0x4b 0x01 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x05 0x4b 0x07 0x4b 0x23 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J7] has backup chain_voltage=870
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[6] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x48 0x00 0x48 0x04 0x48 0x08 0x48 0x00 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x01 0x48 0x01 0x48 0x0f 0x48 0x0f 0x48 0x0f 0x48 0x0f 0x48 0x05 0x48 0x0b 0x48 0x23 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J8] has backup chain_voltage=910
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[7] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 3
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J7] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J7] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J7] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J8] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J8] will use backup chain_voltage_pic=910 [57]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J8] get working chain_voltage_pic=57
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J7] has 63 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J8] has 63 asic
driver-btm-c5.c:4531:set_frequency: Chain[J7] has core num in PIC
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[14] has core num=3
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[16] has core num=4
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[26] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[29] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[31] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[59] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[61] has core num=1
driver-btm-c5.c:4531:set_frequency: Chain[J8] has core num in PIC
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[9] has core num=2
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[42] has core num=15
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[46] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[54] has core num=5
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[61] has core num=15
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[62] has core num=15
driver-btm-c5.c:4571:set_frequency: miner total rate=9055GH/s ideal_total_hash_rate = 9000GH/s
driver-btm-c5.c:4596:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:4598:set_frequency: Chain:6 chipnum=63
driver-btm-c5.c:4618:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:4768:set_frequency: Chain:6 temp offset=0
driver-btm-c5.c:4773:set_frequency: Chain:6 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
driver-btm-c5.c:4809:set_frequency: Chain:6 max freq=656
driver-btm-c5.c:4810:set_frequency: Chain:6 min freq=656
driver-btm-c5.c:4596:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:4598:set_frequency: Chain:7 chipnum=63
driver-btm-c5.c:4618:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:4768:set_frequency: Chain:7 temp offset=0
driver-btm-c5.c:4773:set_frequency: Chain:7 base freq=637
Asic[ 0]:637 Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637
Asic[ 8]:637 Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637
Asic[16]:637 Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637
Asic[24]:637 Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637
Asic[32]:637 Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637
Asic[40]:637 Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637
Asic[48]:637 Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637
Asic[56]:637 Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
driver-btm-c5.c:4809:set_frequency: Chain:7 max freq=637
driver-btm-c5.c:4810:set_frequency: Chain:7 min freq=637
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:4854:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:4855:set_frequency: Chain:6 chipnum=63
driver-btm-c5.c:4874:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:5058:set_frequency: Chain:6 temp offset=0
driver-btm-c5.c:5063:set_frequency: Chain:6 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
driver-btm-c5.c:5110:set_frequency: Chain:6 max freq=656
driver-btm-c5.c:5111:set_frequency: Chain:6 min freq=656
driver-btm-c5.c:4854:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:4855:set_frequency: Chain:7 chipnum=63
driver-btm-c5.c:4874:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:5058:set_frequency: Chain:7 temp offset=0
driver-btm-c5.c:5063:set_frequency: Chain:7 base freq=637
Asic[ 0]:637 Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637
Asic[ 8]:637 Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637
Asic[16]:637 Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637
Asic[24]:637 Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637
Asic[32]:637 Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637
Asic[40]:637 Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637
Asic[48]:637 Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637
Asic[56]:637 Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
driver-btm-c5.c:5110:set_frequency: Chain:7 max freq=637
driver-btm-c5.c:5111:set_frequency: Chain:7 min freq=637
driver-btm-c5.c:5119:set_frequency: max freq = 656
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 9055, fixed_totalRate = 9000
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:6593:calibration_sensor_offset: Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6627:calibration_sensor_offset: chain[7] temp chip I2C addr=0x98
driver-btm-c5.c:6635:calibration_sensor_offset: chain[7] has no middle temp, use special fix mode.
driver-btm-c5.c:6660:calibration_sensor_offset: Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
driver-btm-c5.c:6384:do_calibration_sensor_offset: New offset Chain[7] chip[244] local:23 remote:26 offset:26
driver-btm-c5.c:6753:calibration_sensor_offset: Chain[J7] chip[244] get middle temp offset=26 typeID=55
driver-btm-c5.c:6593:calibration_sensor_offset: Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6627:calibration_sensor_offset: chain[8] temp chip I2C addr=0x98
driver-btm-c5.c:6635:calibration_sensor_offset: chain[8] has no middle temp, use special fix mode.
driver-btm-c5.c:6660:calibration_sensor_offset: Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
driver-btm-c5.c:6384:do_calibration_sensor_offset: New offset Chain[8] chip[244] local:24 remote:28 offset:26
driver-btm-c5.c:6753:calibration_sensor_offset: Chain[J8] chip[244] get middle temp offset=26 typeID=55
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 930
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 930
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 920
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 920
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 910
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 910
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 900
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 890
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 880
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 870
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=319 total_tv_end_sys=320
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = 42
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:10487:check_system_work: voltage_check_done
do read_temp_func once...
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=69.9600 Asic[02]=73.7860 Asic[03]=76.7050 Asic[04]=76.2180 Asic[05]=75.1610 Asic[06]=78.8020 Asic[07]=74.2890 Asic[08]=72.9640
Asic[09]=77.5270 Asic[10]=77.5770 Asic[11]=69.9600 Asic[12]=71.7050 Asic[13]=74.1040 Asic[14]=70.6990 Asic[15]=81.2850 Asic[16]=81.0170
Asic[17]=78.1140 Asic[18]=76.4360 Asic[19]=73.6350 Asic[20]=71.1180 Asic[21]=75.0610 Asic[22]=71.5710 Asic[23]=78.9870 Asic[24]=69.8260
Asic[25]=76.4700 Asic[26]=71.1180 Asic[27]=70.2290 Asic[28]=65.9840 Asic[29]=70.2120 Asic[30]=78.6510 Asic[31]=76.1350 Asic[32]=76.7720
Asic[33]=80.3960 Asic[34]=77.5440 Asic[35]=71.5380 Asic[36]=76.5710 Asic[37]=72.5110 Asic[38]=72.8800 Asic[39]=74.9600 Asic[40]=71.6720
Asic[41]=74.1040 Asic[42]=72.9800 Asic[43]=70.9000 Asic[44]=71.1520 Asic[45]=72.5950 Asic[46]=71.1350 Asic[47]=78.6010 Asic[48]=77.8460
Asic[49]=70.1790 Asic[50]=66.1860 Asic[51]=73.3330 Asic[52]=75.9840 Asic[53]=78.6010 Asic[54]=70.6650 Asic[55]=75.8660 Asic[56]=75.8490
Asic[57]=74.4740 Asic[58]=68.6850 Asic[59]=78.2480 Asic[60]=71.8400 Asic[61]=73.4330 Asic[62]=73.4000 Asic[63]=76.6210
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=72.6280 Asic[02]=71.0510 Asic[03]=71.7560 Asic[04]=74.7920 Asic[05]=75.4970 Asic[06]=71.3530 Asic[07]=71.8730 Asic[08]=73.7690
Asic[09]=68.7020 Asic[10]=70.8160 Asic[11]=74.6580 Asic[12]=77.4770 Asic[13]=79.2380 Asic[14]=73.2490 Asic[15]=75.2790 Asic[16]=71.4370
Asic[17]=72.0740 Asic[18]=72.1250 Asic[19]=71.5880 Asic[20]=73.9030 Asic[21]=74.0370 Asic[22]=77.0910 Asic[23]=70.6480 Asic[24]=68.2160
Asic[25]=74.8590 Asic[26]=68.3330 Asic[27]=73.7190 Asic[28]=72.9470 Asic[29]=73.3330 Asic[30]=78.3320 Asic[31]=73.9200 Asic[32]=76.6880
Asic[33]=71.3360 Asic[34]=74.1040 Asic[35]=74.5240 Asic[36]=73.8860 Asic[37]=74.4060 Asic[38]=70.4470 Asic[39]=73.1480 Asic[40]=76.7220
Asic[41]=69.9940 Asic[42]=72.2250 Asic[43]=75.4470 Asic[44]=73.4000 Asic[45]=76.7550 Asic[46]=79.8250 Asic[47]=73.2320 Asic[48]=75.9500
Asic[49]=73.5840 Asic[50]=71.2190 Asic[51]=73.4500 Asic[52]=75.5810 Asic[53]=81.9560 Asic[54]=71.6720 Asic[55]=73.2660 Asic[56]=76.1850
Asic[57]=73.8860 Asic[58]=72.3760 Asic[59]=68.9200 Asic[60]=72.3090 Asic[61]=67.9640 Asic[62]=69.6250 Asic[63]=74.6250
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[6] Chip[244] pcb temperature=55
Chain[6] Chip[62] junction temperature=64
Special fix Chain[6] Chip[62] middle Temp = 70
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=59
Chain[7] Chip[62] junction temperature=68
Special fix Chain[7] Chip[62] middle Temp = 74
Done read temp on Chain[7]
Max pcb temp : 59
set FAN speed according to: temp_highest=59 temp_top1[PWM_T]=59 temp_top1[TEMP_POS_LOCAL]=59 temp_change=0 fix_fan_steps=0
FAN PWM: 68
read_temp_func Done!
CRC error counter=1
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000013] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000294] ps7-ttc #0 at df804000, irq=43
[ 0.000595] Console: colour dummy device 80x30
[ 0.000624] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040197] pid_max: default: 32768 minimum: 301
[ 0.040405] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040425] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042582] CPU: Testing write buffer coherency: ok
[ 0.042893] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042950] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.043170] L310 cache controller enabled
[ 0.043190] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.120985] CPU1: Booted secondary processor
[ 0.210218] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210347] Brought up 2 CPUs
[ 0.210365] SMP: Total of 2 processors activated.
[ 0.210374] CPU: All CPU(s) started in SVC mode.
[ 0.211031] devtmpfs: initialized
[ 0.213463] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214648] regulator-dummy: no parameters
[ 0.222003] NET: Registered protocol family 16
[ 0.224271] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226530] cpuidle: using governor ladder
[ 0.226544] cpuidle: using governor menu
[ 0.233917] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235426] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235440] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235548] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.256893] bio: create slab <bio-0> at 0
[ 0.258286] vgaarb: loaded
[ 0.258970] SCSI subsystem initialized
[ 0.259858] usbcore: registered new interface driver usbfs
[ 0.260027] usbcore: registered new interface driver hub
[ 0.260378] usbcore: registered new device driver usb
[ 0.260909] media: Linux media interface: v0.10
[ 0.261098] Linux video capture interface: v2.00
[ 0.261384] pps_core: LinuxPPS API ver. 1 registered
[ 0.261395] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.261521] PTP clock support registered
[ 0.261889] EDAC MC: Ver: 3.0.0
[ 0.263074] Advanced Linux Sound Architecture Driver Initialized.
[ 0.265809] DMA-API: preallocated 4096 debug entries
[ 0.265822] DMA-API: debugging enabled by kernel config
[ 0.265890] Switched to clocksource arm_global_timer
[ 0.285679] NET: Registered protocol family 2
[ 0.286714] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.286771] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.286856] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.286902] TCP: reno registered
[ 0.286918] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.286946] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.287722] NET: Registered protocol family 1
[ 0.288237] RPC: Registered named UNIX socket transport module.
[ 0.288250] RPC: Registered udp transport module.
[ 0.288259] RPC: Registered tcp transport module.
[ 0.288267] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288279] PCI: CLS 0 bytes, default 64
[ 0.288705] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.290689] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.292721] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.292907] msgmni has been set to 967
[ 0.293678] io scheduler noop registered
[ 0.293691] io scheduler deadline registered
[ 0.293731] io scheduler cfq registered (default)
[ 0.304958] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.304979] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.428483] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.995797] console [ttyPS0] enabled
[ 1.000062] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.007694] [drm] Initialized drm 1.1.0 20060810
[ 1.024751] brd: module loaded
[ 1.034162] loop: module loaded
[ 1.043514] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.049340] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.057163] libphy: XEMACPS mii bus: probed
[ 1.061533] ------------- phy_id = 0x3625e62
[ 1.066448] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.075019] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.081857] ehci-pci: EHCI PCI platform driver
[ 1.089157] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.096005] usbcore: registered new interface driver usb-storage
[ 1.102823] mousedev: PS/2 mouse device common for all mice
[ 1.108930] i2c /dev entries driver
[ 1.115792] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.121305] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.127227] Xilinx Zynq CpuIdle Driver started
[ 1.132078] sdhci: Secure Digital Host Controller Interface driver
[ 1.138191] sdhci: Copyright(c) Pierre Ossman
[ 1.142508] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.149389] mmc0: no vqmmc regulator found
[ 1.153405] mmc0: no vmmc regulator found
[ 1.195912] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.204582] usbcore: registered new interface driver usbhid
[ 1.210084] usbhid: USB HID core driver
[ 1.214794] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221090] nand: Micron MT29F2G08ABAEAWP
[ 1.225058] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.230992] Bad block table found at page 131008, version 0x01
[ 1.237216] Bad block table found at page 130944, version 0x01
[ 1.243266] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249046] Creating 3 MTD partitions on "pl353-nand":
[ 1.254139] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.262186] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.269486] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.280204] TCP: cubic registered
[ 1.283440] NET: Registered protocol family 17
[ 1.288131] Registering SWP/SWPB emulation handler
[ 1.294006] regulator-dummy: disabling
[ 1.298319] UBI: attaching mtd1 to ubi0
[ 1.684981] UBI: scanning is finished
[ 1.696800] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.703855] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.710649] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.717328] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.724165] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.730175] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.737286] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1113221046
[ 1.746316] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.755513] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.755518] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.759431] ALSA device list:
[ 1.759434] No soundcards found.
[ 1.776369] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.906640] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.912570] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.921708] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.931587] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.936626] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[ 1.964552] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.990392] devtmpfs: mounted
[ 1.993496] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.126367] random: dd urandom read with 1 bits of entropy available
[ 3.735941]
[ 3.735941] bcm54xx_config_init
[ 4.805941]
[ 4.805941] bcm54xx_config_init
[ 20.806767] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 20.812860] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 35.585636] In axi fpga driver!
[ 35.588722] request_mem_region OK!
[ 35.592098] AXI fpga dev virtual address is 0xdf9fe000
[ 35.597221] *base_vir_addr = 0xc51e
[ 35.611846] In fpga mem driver!
[ 35.615134] request_mem_region OK!
[ 35.618767] fpga mem virtual address is 0xe2000000
[ 36.395915]
[ 36.395915] bcm54xx_config_init
[ 37.485938]
[ 37.485938] bcm54xx_config_init
[ 53.486765] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 53.492781] xemacps e000b000.ps7-ethernet: link up (100/FULL)
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 507486208
main.c:14031: Detect 512MB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6fda000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5dd3000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 817c142c68808814
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x000000e0
driver-bitmain.c:1946: Find hashboard on Chain[5]
driver-bitmain.c:1946: Find hashboard on Chain[6]
driver-bitmain.c:1946: Find hashboard on Chain[7]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[6] has freq in PIC and will jump over...
main.c:9103: Chain[6] has core num in PIC
main.c:9113: Chain[6] ASIC[14] has core num=3
main.c:9113: Chain[6] ASIC[16] has core num=4
main.c:9113: Chain[6] ASIC[26] has core num=1
main.c:9113: Chain[6] ASIC[29] has core num=1
main.c:9113: Chain[6] ASIC[31] has core num=1
main.c:9113: Chain[6] ASIC[59] has core num=1
main.c:9113: Chain[6] ASIC[61] has core num=1
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[7] has freq in PIC and will jump over...
main.c:9103: Chain[7] has core num in PIC
main.c:9113: Chain[7] ASIC[9] has core num=2
main.c:9113: Chain[7] ASIC[42] has core num=15
main.c:9113: Chain[7] ASIC[46] has core num=1
main.c:9113: Chain[7] ASIC[54] has core num=5
main.c:9113: Chain[7] ASIC[61] has core num=15
main.c:9113: Chain[7] ASIC[62] has core num=15
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9183: get PIC voltage=6 on chain[6], value=940
main.c:9183: get PIC voltage=6 on chain[7], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:9349: chain[6] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[6] temp chip I2C addr=0x98
main.c:9372: chain[6] has no middle temp, use special fix mode.
main.c:9349: chain[7] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[7] temp chip I2C addr=0x98
main.c:9372: chain[7] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 3
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 3, total chain num = 3
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found= 4754 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12292:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 817c142c68808814
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=8880
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x0b 0x4a 0x09 0x4a 0x04 0x4a 0x0a 0x4a 0x00 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x03 0x4a 0x01 0x4a 0x01 0x4a 0x0f 0x4a 0x0f 0x4a 0x0f 0x4a 0x0f 0x4a 0x05 0x4a 0x07 0x4a 0x23 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a 0x00 0x4a
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=870
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4b 0x00 0x4b 0x04 0x4b 0x0b 0x4b 0x00 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x01 0x4b 0x01 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x05 0x4b 0x07 0x4b 0x23 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J7] has backup chain_voltage=870
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[6] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x48 0x00 0x48 0x04 0x48 0x08 0x48 0x00 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x03 0x48 0x01 0x48 0x01 0x48 0x0f 0x48 0x0f 0x48 0x0f 0x48 0x0f 0x48 0x05 0x48 0x0b 0x48 0x23 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48 0x00 0x48
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J8] has backup chain_voltage=910
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[7] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 3
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J7] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J7] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J7] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J8] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J8] will use backup chain_voltage_pic=910 [57]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J8] get working chain_voltage_pic=57
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J7] has 63 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J8] has 63 asic
driver-btm-c5.c:4531:set_frequency: Chain[J7] has core num in PIC
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[14] has core num=3
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[16] has core num=4
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[26] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[29] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[31] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[59] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J7] ASIC[61] has core num=1
driver-btm-c5.c:4531:set_frequency: Chain[J8] has core num in PIC
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[9] has core num=2
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[42] has core num=15
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[46] has core num=1
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[54] has core num=5
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[61] has core num=15
driver-btm-c5.c:4541:set_frequency: Chain[J8] ASIC[62] has core num=15
driver-btm-c5.c:4571:set_frequency: miner total rate=9055GH/s ideal_total_hash_rate = 9000GH/s
driver-btm-c5.c:4596:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:4598:set_frequency: Chain:6 chipnum=63
driver-btm-c5.c:4618:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:4768:set_frequency: Chain:6 temp offset=0
driver-btm-c5.c:4773:set_frequency: Chain:6 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
driver-btm-c5.c:4809:set_frequency: Chain:6 max freq=656
driver-btm-c5.c:4810:set_frequency: Chain:6 min freq=656
driver-btm-c5.c:4596:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:4598:set_frequency: Chain:7 chipnum=63
driver-btm-c5.c:4618:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:4768:set_frequency: Chain:7 temp offset=0
driver-btm-c5.c:4773:set_frequency: Chain:7 base freq=637
Asic[ 0]:637 Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637
Asic[ 8]:637 Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637
Asic[16]:637 Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637
Asic[24]:637 Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637
Asic[32]:637 Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637
Asic[40]:637 Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637
Asic[48]:637 Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637
Asic[56]:637 Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
driver-btm-c5.c:4809:set_frequency: Chain:7 max freq=637
driver-btm-c5.c:4810:set_frequency: Chain:7 min freq=637
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:4854:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:4855:set_frequency: Chain:6 chipnum=63
driver-btm-c5.c:4874:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:5058:set_frequency: Chain:6 temp offset=0
driver-btm-c5.c:5063:set_frequency: Chain:6 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
driver-btm-c5.c:5110:set_frequency: Chain:6 max freq=656
driver-btm-c5.c:5111:set_frequency: Chain:6 min freq=656
driver-btm-c5.c:4854:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:4855:set_frequency: Chain:7 chipnum=63
driver-btm-c5.c:4874:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:5058:set_frequency: Chain:7 temp offset=0
driver-btm-c5.c:5063:set_frequency: Chain:7 base freq=637
Asic[ 0]:637 Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637
Asic[ 8]:637 Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637
Asic[16]:637 Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637
Asic[24]:637 Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637
Asic[32]:637 Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637
Asic[40]:637 Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637
Asic[48]:637 Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637
Asic[56]:637 Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
driver-btm-c5.c:5110:set_frequency: Chain:7 max freq=637
driver-btm-c5.c:5111:set_frequency: Chain:7 min freq=637
driver-btm-c5.c:5119:set_frequency: max freq = 656
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 9055, fixed_totalRate = 9000
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:6593:calibration_sensor_offset: Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6627:calibration_sensor_offset: chain[7] temp chip I2C addr=0x98
driver-btm-c5.c:6635:calibration_sensor_offset: chain[7] has no middle temp, use special fix mode.
driver-btm-c5.c:6660:calibration_sensor_offset: Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
driver-btm-c5.c:6384:do_calibration_sensor_offset: New offset Chain[7] chip[244] local:23 remote:26 offset:26
driver-btm-c5.c:6753:calibration_sensor_offset: Chain[J7] chip[244] get middle temp offset=26 typeID=55
driver-btm-c5.c:6593:calibration_sensor_offset: Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6627:calibration_sensor_offset: chain[8] temp chip I2C addr=0x98
driver-btm-c5.c:6635:calibration_sensor_offset: chain[8] has no middle temp, use special fix mode.
driver-btm-c5.c:6660:calibration_sensor_offset: Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
driver-btm-c5.c:6384:do_calibration_sensor_offset: New offset Chain[8] chip[244] local:24 remote:28 offset:26
driver-btm-c5.c:6753:calibration_sensor_offset: Chain[J8] chip[244] get middle temp offset=26 typeID=55
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 930
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 930
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 920
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 920
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 910
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[7] set voltage to 910
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 900
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 890
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 880
driver-btm-c5.c:12083:slowly_downgrade_voltage_all_chain: chain[6] set voltage to 870
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=319 total_tv_end_sys=320
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = 42
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:10487:check_system_work: voltage_check_done
do read_temp_func once...
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=69.9600 Asic[02]=73.7860 Asic[03]=76.7050 Asic[04]=76.2180 Asic[05]=75.1610 Asic[06]=78.8020 Asic[07]=74.2890 Asic[08]=72.9640
Asic[09]=77.5270 Asic[10]=77.5770 Asic[11]=69.9600 Asic[12]=71.7050 Asic[13]=74.1040 Asic[14]=70.6990 Asic[15]=81.2850 Asic[16]=81.0170
Asic[17]=78.1140 Asic[18]=76.4360 Asic[19]=73.6350 Asic[20]=71.1180 Asic[21]=75.0610 Asic[22]=71.5710 Asic[23]=78.9870 Asic[24]=69.8260
Asic[25]=76.4700 Asic[26]=71.1180 Asic[27]=70.2290 Asic[28]=65.9840 Asic[29]=70.2120 Asic[30]=78.6510 Asic[31]=76.1350 Asic[32]=76.7720
Asic[33]=80.3960 Asic[34]=77.5440 Asic[35]=71.5380 Asic[36]=76.5710 Asic[37]=72.5110 Asic[38]=72.8800 Asic[39]=74.9600 Asic[40]=71.6720
Asic[41]=74.1040 Asic[42]=72.9800 Asic[43]=70.9000 Asic[44]=71.1520 Asic[45]=72.5950 Asic[46]=71.1350 Asic[47]=78.6010 Asic[48]=77.8460
Asic[49]=70.1790 Asic[50]=66.1860 Asic[51]=73.3330 Asic[52]=75.9840 Asic[53]=78.6010 Asic[54]=70.6650 Asic[55]=75.8660 Asic[56]=75.8490
Asic[57]=74.4740 Asic[58]=68.6850 Asic[59]=78.2480 Asic[60]=71.8400 Asic[61]=73.4330 Asic[62]=73.4000 Asic[63]=76.6210
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=72.6280 Asic[02]=71.0510 Asic[03]=71.7560 Asic[04]=74.7920 Asic[05]=75.4970 Asic[06]=71.3530 Asic[07]=71.8730 Asic[08]=73.7690
Asic[09]=68.7020 Asic[10]=70.8160 Asic[11]=74.6580 Asic[12]=77.4770 Asic[13]=79.2380 Asic[14]=73.2490 Asic[15]=75.2790 Asic[16]=71.4370
Asic[17]=72.0740 Asic[18]=72.1250 Asic[19]=71.5880 Asic[20]=73.9030 Asic[21]=74.0370 Asic[22]=77.0910 Asic[23]=70.6480 Asic[24]=68.2160
Asic[25]=74.8590 Asic[26]=68.3330 Asic[27]=73.7190 Asic[28]=72.9470 Asic[29]=73.3330 Asic[30]=78.3320 Asic[31]=73.9200 Asic[32]=76.6880
Asic[33]=71.3360 Asic[34]=74.1040 Asic[35]=74.5240 Asic[36]=73.8860 Asic[37]=74.4060 Asic[38]=70.4470 Asic[39]=73.1480 Asic[40]=76.7220
Asic[41]=69.9940 Asic[42]=72.2250 Asic[43]=75.4470 Asic[44]=73.4000 Asic[45]=76.7550 Asic[46]=79.8250 Asic[47]=73.2320 Asic[48]=75.9500
Asic[49]=73.5840 Asic[50]=71.2190 Asic[51]=73.4500 Asic[52]=75.5810 Asic[53]=81.9560 Asic[54]=71.6720 Asic[55]=73.2660 Asic[56]=76.1850
Asic[57]=73.8860 Asic[58]=72.3760 Asic[59]=68.9200 Asic[60]=72.3090 Asic[61]=67.9640 Asic[62]=69.6250 Asic[63]=74.6250
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[6] Chip[244] pcb temperature=55
Chain[6] Chip[62] junction temperature=64
Special fix Chain[6] Chip[62] middle Temp = 70
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=59
Chain[7] Chip[62] junction temperature=68
Special fix Chain[7] Chip[62] middle Temp = 74
Done read temp on Chain[7]
Max pcb temp : 59
set FAN speed according to: temp_highest=59 temp_top1[PWM_T]=59 temp_top1[TEMP_POS_LOCAL]=59 temp_change=0 fix_fan_steps=0
FAN PWM: 68
read_temp_func Done!
CRC error counter=1
https://imgur.com/a/4MkvioR
thanks for your help everyone
hi your miner fund only two hashboard from 3 hashboards
check your flat and power cables if your problem didn't solve your hashboard in chain 5 need to repair.
@bitmaxz every time I try to flash via website it says incorrect file. will it be different if I use sd card?
It will be incorrect file if you are trying to flash SD card image through browser.
You need SD card and put all extracted file to SD card. Follow the guide from the link that I posted above.
Or if your miner control board is c5 then you wont be able to flash it through SD card. Use the firmware with extension tar.gz that support c5 controller and upgrade it through browser.
I updated through web browser and the problem is the same. here's the new log
Quote
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.10.31-ltsi-00003-gcf03eb9 (lzq@armdev01) (gcc version 4.7.3 20121106 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2012.11-20121123 - Linaro GCC 2012.11) ) #81 SMP Mon Apr 25 11:20:36 CST 2016
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Altera SOCFPGA, model: Altera SOCFPGA Cyclone V
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 258048
free_area_init_node: node 0, pgdat 806e5cc0, node_mem_map 8072a000
Normal zone: 2016 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 258048 pages, LIFO batch:31
PERCPU: Embedded 8 pages/cpu @80f17000 s11200 r8192 d13376 u32768
pcpu-alloc: s11200 r8192 d13376 u32768 alloc=8*4096
pcpu-alloc:
Kernel command line: mem=1008M console=ttyS0,115200 root=/dev/mtdblock3 rw rootfstype=jffs2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1008MB = 1008MB total
Memory: 1015844k/1015844k available, 16348k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xbf800000 - 0xff000000 (1016 MB)
lowmem : 0x80000000 - 0xbf000000 (1008 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x8065a930 (6475 kB)
.init : 0x8065b000 - 0x806adbc0 ( 331 kB)
.data : 0x806ae000 - 0x806e9990 ( 239 kB)
.bss : 0x806e9990 - 0x80729384 ( 255 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 17687 entries in 52 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x804ab220 - 0x804ab278
CPU1: failed to come online
Brought up 1 CPUs
SMP: Total of 1 processors activated (1196.85 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
NET: Registered protocol family 16
fpga bridge driver
DMA: preallocated 256 KiB pool for atomic coherent allocations
L310 cache controller enabled
l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x32460000, Cache size: 524288 B
syscon fffef000.l2-cache: regmap [mem 0xfffef000-0xfffeffff] registered
syscon ffd05000.rstmgr: regmap [mem 0xffd05000-0xffd05fff] registered
syscon ffc25000.sdrctl: regmap [mem 0xffc25000-0xffc25fff] registered
syscon ff800000.l3regs: regmap [mem 0xff800000-0xff800fff] registered
syscon ffd08000.sysmgr: regmap [mem 0xffd08000-0xffd0bfff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
altera_hps2fpga_bridge fpgabridge.2: fpga bridge [hps2fpga] registered as device hps2fpga
altera_hps2fpga_bridge fpgabridge.2: init-val not specified
altera_hps2fpga_bridge fpgabridge.3: fpga bridge [lshps2fpga] registered as device lwhps2fpga
altera_hps2fpga_bridge fpgabridge.3: init-val not specified
altera_hps2fpga_bridge fpgabridge.4: fpga bridge [fpga2hps] registered as device fpga2hps
altera_hps2fpga_bridge fpgabridge.4: init-val not specified
bio: create slab <bio-0> at 0
FPGA Mangager framework driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Switching to clocksource timer0
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
arm-pmu arm-pmu: PMU:CTI successfully enabled for 1 cores
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
NTFS driver 2.1.30 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1984
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194) is a 16550A
console [ttyS0] enabled
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
brd: module loaded
denali-nand-dt ff900000.nand: Dump timing register values:acc_clks: 4, re_2_we: 20, re_2_re: 20
we_2_re: 12, addr_2_data: 14, rdwr_en_lo_cnt: 2
rdwr_en_hi_cnt: 2, cs_setup_cnt: 2
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
5 ofpart partitions found on MTD device denali-nand
Creating 5 MTD partitions on "denali-nand":
0x000000000000-0x000001000000 : "NAND Flash Boot Area 16MB"
0x000001000000-0x000002000000 : "NAND Flash Boot Area backup1 16MB"
0x000002000000-0x000003000000 : "NAND Flash Boot Area backup2 16MB"
0x000003000000-0x00000b000000 : "NAND Flash jffs2 Root Filesystem 128MB"
0x00000b000000-0x000010000000 : "NAND Flash jffs2 Root Filesystem 80MB"
dw_spi_mmio fff00000.spi: master is unqueued, this is deprecated
CAN device driver interface
c_can_platform ffc00000.d_can: invalid resource
c_can_platform ffc00000.d_can: control memory is not used for raminit
c_can_platform ffc00000.d_can: c_can_platform device registered (regs=bf8dc000, irq=163)
stmmac_hw_init: 1000M
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Enhanced/Alternate descriptors
Enabled extended descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Synopsys Designware Multimedia Card Interface Driver
dwmmc_socfpga ff704000.dwmmc0: couldn't determine pwr-en, assuming pwr-en = 0
dwmmc_socfpga ff704000.dwmmc0: Using internal DMA controller.
dwmmc_socfpga ff704000.dwmmc0: Version ID is 240a
dwmmc_socfpga ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
dwmmc_socfpga ff704000.dwmmc0: 1 slots initialized
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
ThumbEE CPU extension supported.
Registering SWP/SWPB emulation handler
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
jffs2: Empty flash at 0x0139ba2c ends at 0x0139c000
VFS: Mounted root (jffs2 filesystem) on device 31:3.
devtmpfs: mounted
Freeing unused kernel memory: 328K (8065b000 - 806ad000)
eth0: device MAC address ae:f6:07:a7:36:08
init phy ok
PHY DMA init OK
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: stmmac-0:00 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
Original value in RESET_MANAGER_BASE_ADDR + BRGMODRST_ADDR is 0x0
request_mem_region OK!
AXI fpga dev virtual address is 0xbf942000
*base_vir_addr = 0xc504
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xc0000000
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: stmmac-0:00 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[0]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Check chain[0] PIC fw version=0x02
Check chain[2] PIC fw version=0x02
Check chain[3] PIC fw version=0x02
chain[0] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[0] PIC fw version=0x02
chain[2] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[2] PIC fw version=0x02
chain[3] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[3] PIC fw version=0x02
set command mode to VIL
singleBoardTest: AsicType = 1387
singleBoardTest: asicNum = 64
singleBoardTest: real AsicNum = 63
--- check asic number
set_baud=1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[0]
disable_pic_dac on chain[2]
disable_pic_dac on chain[3]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
Check chain[0] PIC fw version=0x02
Check chain[2] PIC fw version=0x02
Check chain[3] PIC fw version=0x02
Chain[J1] chain_voltage=6 value=940
Chain[J3] chain_voltage=6 value=940
Chain[J4] chain_voltage=6 value=940
Chain[J1] has 62 asic
Chain[J3] has 63 asic
Chain[J4] has 63 asic
Chain[J1] has no freq in PIC, set default freq=550M
Chain[J1] has no core num in PIC
Chain[J3] has no freq in PIC, set default freq=550M
Chain[J3] has no core num in PIC
Chain[J4] has no freq in PIC, set default freq=550M
Chain[J4] has no core num in PIC
read PIC voltage=940 on chain[0]
Chain:0 chipnum=62
Chain[J1] voltage added=0.0V
Chain[J1] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:0 temp offset=0
Chain:0 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550
Chain:0 max freq=550
Chain:0 min freq=550
read PIC voltage=940 on chain[2]
Chain:2 chipnum=63
Chain[J3] voltage added=0.0V
Chain[J3] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:2 temp offset=0
Chain:2 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:2 max freq=550
Chain:2 min freq=550
read PIC voltage=940 on chain[3]
Chain:3 chipnum=63
Chain[J4] voltage added=0.0V
Chain[J4] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:3 temp offset=0
Chain:3 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:3 max freq=550
Chain:3 min freq=550
Miner fix freq ...
read PIC voltage=940 on chain[0]
Chain:0 chipnum=62
Chain[J1] voltage added=0.0V
Chain[J1] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:0 temp offset=0
Chain:0 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550
Chain:0 max freq=550
Chain:0 min freq=550
read PIC voltage=940 on chain[2]
Chain:2 chipnum=63
Chain[J3] voltage added=0.0V
Chain[J3] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:2 temp offset=0
Chain:2 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:2 max freq=550
Chain:2 min freq=550
read PIC voltage=940 on chain[3]
Chain:3 chipnum=63
Chain[J4] voltage added=0.0V
Chain[J4] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:3 temp offset=0
Chain:3 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:3 max freq=550
Chain:3 min freq=550
max freq = 550
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[0]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
use PIC voltage=940 on chain[0]
now set pic voltage=6 on chain[0]
use PIC voltage=940 on chain[2]
now set pic voltage=6 on chain[2]
use PIC voltage=940 on chain[3]
now set pic voltage=6 on chain[3]
enable_pic_dac on chain[0]
enable_pic_dac on chain[2]
enable_pic_dac on chain[3]
do 12 8xPatten test for 1 times
set command mode to VIL
initFpgaBoard: AsicType = 1387
initFpgaBoard: asicNum = 64
initFpgaBoard: real AsicNum = 63
--- check asic number
check chain[0]: asicNum = 63
check chain[2]: asicNum = 63
check chain[3]: asicNum = 63
Set Freq of PIC for Test Patten on Chain[0]
Initializing cgroup subsys cpuset
Linux version 3.10.31-ltsi-00003-gcf03eb9 (lzq@armdev01) (gcc version 4.7.3 20121106 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2012.11-20121123 - Linaro GCC 2012.11) ) #81 SMP Mon Apr 25 11:20:36 CST 2016
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Altera SOCFPGA, model: Altera SOCFPGA Cyclone V
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 258048
free_area_init_node: node 0, pgdat 806e5cc0, node_mem_map 8072a000
Normal zone: 2016 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 258048 pages, LIFO batch:31
PERCPU: Embedded 8 pages/cpu @80f17000 s11200 r8192 d13376 u32768
pcpu-alloc: s11200 r8192 d13376 u32768 alloc=8*4096
pcpu-alloc:
- 0
- 1
Kernel command line: mem=1008M console=ttyS0,115200 root=/dev/mtdblock3 rw rootfstype=jffs2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1008MB = 1008MB total
Memory: 1015844k/1015844k available, 16348k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xbf800000 - 0xff000000 (1016 MB)
lowmem : 0x80000000 - 0xbf000000 (1008 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x8065a930 (6475 kB)
.init : 0x8065b000 - 0x806adbc0 ( 331 kB)
.data : 0x806ae000 - 0x806e9990 ( 239 kB)
.bss : 0x806e9990 - 0x80729384 ( 255 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 17687 entries in 52 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x804ab220 - 0x804ab278
CPU1: failed to come online
Brought up 1 CPUs
SMP: Total of 1 processors activated (1196.85 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
NET: Registered protocol family 16
fpga bridge driver
DMA: preallocated 256 KiB pool for atomic coherent allocations
L310 cache controller enabled
l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x32460000, Cache size: 524288 B
syscon fffef000.l2-cache: regmap [mem 0xfffef000-0xfffeffff] registered
syscon ffd05000.rstmgr: regmap [mem 0xffd05000-0xffd05fff] registered
syscon ffc25000.sdrctl: regmap [mem 0xffc25000-0xffc25fff] registered
syscon ff800000.l3regs: regmap [mem 0xff800000-0xff800fff] registered
syscon ffd08000.sysmgr: regmap [mem 0xffd08000-0xffd0bfff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
altera_hps2fpga_bridge fpgabridge.2: fpga bridge [hps2fpga] registered as device hps2fpga
altera_hps2fpga_bridge fpgabridge.2: init-val not specified
altera_hps2fpga_bridge fpgabridge.3: fpga bridge [lshps2fpga] registered as device lwhps2fpga
altera_hps2fpga_bridge fpgabridge.3: init-val not specified
altera_hps2fpga_bridge fpgabridge.4: fpga bridge [fpga2hps] registered as device fpga2hps
altera_hps2fpga_bridge fpgabridge.4: init-val not specified
bio: create slab <bio-0> at 0
FPGA Mangager framework driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Switching to clocksource timer0
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
arm-pmu arm-pmu: PMU:CTI successfully enabled for 1 cores
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
NTFS driver 2.1.30 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1984
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194) is a 16550A
console [ttyS0] enabled
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
brd: module loaded
denali-nand-dt ff900000.nand: Dump timing register values:acc_clks: 4, re_2_we: 20, re_2_re: 20
we_2_re: 12, addr_2_data: 14, rdwr_en_lo_cnt: 2
rdwr_en_hi_cnt: 2, cs_setup_cnt: 2
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
5 ofpart partitions found on MTD device denali-nand
Creating 5 MTD partitions on "denali-nand":
0x000000000000-0x000001000000 : "NAND Flash Boot Area 16MB"
0x000001000000-0x000002000000 : "NAND Flash Boot Area backup1 16MB"
0x000002000000-0x000003000000 : "NAND Flash Boot Area backup2 16MB"
0x000003000000-0x00000b000000 : "NAND Flash jffs2 Root Filesystem 128MB"
0x00000b000000-0x000010000000 : "NAND Flash jffs2 Root Filesystem 80MB"
dw_spi_mmio fff00000.spi: master is unqueued, this is deprecated
CAN device driver interface
c_can_platform ffc00000.d_can: invalid resource
c_can_platform ffc00000.d_can: control memory is not used for raminit
c_can_platform ffc00000.d_can: c_can_platform device registered (regs=bf8dc000, irq=163)
stmmac_hw_init: 1000M
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Enhanced/Alternate descriptors
Enabled extended descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Synopsys Designware Multimedia Card Interface Driver
dwmmc_socfpga ff704000.dwmmc0: couldn't determine pwr-en, assuming pwr-en = 0
dwmmc_socfpga ff704000.dwmmc0: Using internal DMA controller.
dwmmc_socfpga ff704000.dwmmc0: Version ID is 240a
dwmmc_socfpga ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
dwmmc_socfpga ff704000.dwmmc0: 1 slots initialized
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
ThumbEE CPU extension supported.
Registering SWP/SWPB emulation handler
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
jffs2: Empty flash at 0x0139ba2c ends at 0x0139c000
VFS: Mounted root (jffs2 filesystem) on device 31:3.
devtmpfs: mounted
Freeing unused kernel memory: 328K (8065b000 - 806ad000)
eth0: device MAC address ae:f6:07:a7:36:08
init phy ok
PHY DMA init OK
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: stmmac-0:00 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
Original value in RESET_MANAGER_BASE_ADDR + BRGMODRST_ADDR is 0x0
request_mem_region OK!
AXI fpga dev virtual address is 0xbf942000
*base_vir_addr = 0xc504
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xc0000000
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: device MAC address 00:91:6b:66:c0:ed
init phy ok
PHY DMA init OK
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: stmmac-0:00 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[0]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Check chain[0] PIC fw version=0x02
Check chain[2] PIC fw version=0x02
Check chain[3] PIC fw version=0x02
chain[0] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[0] PIC fw version=0x02
chain[2] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[2] PIC fw version=0x02
chain[3] has no freq in PIC! Will use default freq=550 and jump over...
Check chain[3] PIC fw version=0x02
set command mode to VIL
singleBoardTest: AsicType = 1387
singleBoardTest: asicNum = 64
singleBoardTest: real AsicNum = 63
--- check asic number
set_baud=1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[0]
disable_pic_dac on chain[2]
disable_pic_dac on chain[3]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
Check chain[0] PIC fw version=0x02
Check chain[2] PIC fw version=0x02
Check chain[3] PIC fw version=0x02
Chain[J1] chain_voltage=6 value=940
Chain[J3] chain_voltage=6 value=940
Chain[J4] chain_voltage=6 value=940
Chain[J1] has 62 asic
Chain[J3] has 63 asic
Chain[J4] has 63 asic
Chain[J1] has no freq in PIC, set default freq=550M
Chain[J1] has no core num in PIC
Chain[J3] has no freq in PIC, set default freq=550M
Chain[J3] has no core num in PIC
Chain[J4] has no freq in PIC, set default freq=550M
Chain[J4] has no core num in PIC
read PIC voltage=940 on chain[0]
Chain:0 chipnum=62
Chain[J1] voltage added=0.0V
Chain[J1] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:0 temp offset=0
Chain:0 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550
Chain:0 max freq=550
Chain:0 min freq=550
read PIC voltage=940 on chain[2]
Chain:2 chipnum=63
Chain[J3] voltage added=0.0V
Chain[J3] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:2 temp offset=0
Chain:2 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:2 max freq=550
Chain:2 min freq=550
read PIC voltage=940 on chain[3]
Chain:3 chipnum=63
Chain[J4] voltage added=0.0V
Chain[J4] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:3 temp offset=0
Chain:3 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:3 max freq=550
Chain:3 min freq=550
Miner fix freq ...
read PIC voltage=940 on chain[0]
Chain:0 chipnum=62
Chain[J1] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:0 temp offset=0
Chain:0 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550
Chain:0 max freq=550
Chain:0 min freq=550
read PIC voltage=940 on chain[2]
Chain:2 chipnum=63
Chain[J3] voltage added=0.0V
Chain[J3] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:2 temp offset=0
Chain:2 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:2 max freq=550
Chain:2 min freq=550
read PIC voltage=940 on chain[3]
Chain:3 chipnum=63
Chain[J4] voltage added=0.0V
Chain[J4] [minerMAC: 00:91:6b:66:c0:ed hashMAC: 00:00:00:00:00:00]
Chain:3 temp offset=0
Chain:3 base freq=100
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:3 max freq=550
Chain:3 min freq=550
max freq = 550
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[0]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
use PIC voltage=940 on chain[0]
now set pic voltage=6 on chain[0]
use PIC voltage=940 on chain[2]
now set pic voltage=6 on chain[2]
use PIC voltage=940 on chain[3]
now set pic voltage=6 on chain[3]
enable_pic_dac on chain[0]
enable_pic_dac on chain[2]
enable_pic_dac on chain[3]
do 12 8xPatten test for 1 times
set command mode to VIL
initFpgaBoard: AsicType = 1387
initFpgaBoard: asicNum = 64
initFpgaBoard: real AsicNum = 63
--- check asic number
check chain[0]: asicNum = 63
check chain[2]: asicNum = 63
check chain[3]: asicNum = 63
Set Freq of PIC for Test Patten on Chain[0]
please disconnect your chain 1 and power on your miner without chain 1 maybe your problem fix.
after all your chain 1 hashboard need to repaired and only find 62 asic, that must be 63 asic.
Installed Bitmain's original firmware Bitmain_Antminer-S17Pro-user-OM-201908201037-sig. I've included the whole log and what sticks out is
Chain[2] PIC init failed!
set_miner_status: ERROR_SOC_INIT
stop mining: soc init failed!
So replaced PIC chip with new, flashed a good hex onto it. I'm not sure what to look for next and appreciate any direction on next moves. Thank you.
Edit: I am running with just this board connected.
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203504K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25872K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12832K (cce79000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2669066886
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 9310506E-3F77-43CC-B7AB-7CFF20C05DA7, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 53/24, WL threshold: 4096, image sequence number: 121791118
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 15BA4C69-FA5C-4D1E-BF20-090C8AD78A1C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-07 18:20:04 driver-btm-api.c:758:init_freq_mode: This is scan-user version
2021-08-07 18:20:04 driver-btm-api.c:1954:bitmain_soc_init: opt_multi_version = 1
2021-08-07 18:20:04 driver-btm-api.c:1955:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-07 18:20:04 driver-btm-api.c:1956:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-07 18:20:04 driver-btm-api.c:1957:bitmain_soc_init: Miner compile time: Tue Aug 20 10:37:07 CST 2019 type: Antminer S17 Pro
2021-08-07 18:20:04 driver-btm-api.c:1958:bitmain_soc_init: commit version: 4b64fd6 2019-08-19 22:09:12, build by: lol 2019-08-20 10:47:29
2021-08-07 18:20:04 driver-btm-api.c:1776:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-07 18:20:04 driver-btm-api.c:1236:miner_device_init: Detect 256MB control board of XILINX
2021-08-07 18:20:04 driver-btm-api.c:1184:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-07 18:20:04 thread.c:653:create_read_nonce_reg_thread: create thread
2021-08-07 18:20:10 driver-btm-api.c:1168:init_miner_version: miner ID : 8164ac2e57408854
2021-08-07 18:20:10 driver-btm-api.c:1174:init_miner_version: FPGA Version = 0xB013
2021-08-07 18:20:11 driver-btm-api.c:820:get_product_id: product_id[2] = 0
2021-08-07 18:20:11 driver-btm-api.c:771:_set_project_type: project:0
2021-08-07 18:20:11 driver-btm-api.c:796:_set_project_type: Project type: Antminer S17 Pro
2021-08-07 18:20:11 driver-btm-api.c:807:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
2021-08-07 18:20:11 driver-btm-api.c:808:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
2021-08-07 18:20:15 driver-btm-api.c:1877:bitmain_board_init: Fan check passed.
2021-08-07 18:20:26 driver-btm-api.c:309:init_pic: Chain[2] PIC init failed!
2021-08-07 18:20:26 driver-btm-api.c:191:set_miner_status: ERROR_PIC_LOST
2021-08-07 18:20:26 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-08-07 18:20:48 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xff
2021-08-07 18:20:48 driver-btm-api.c:191:set_miner_status: ERROR_SOC_INIT
2021-08-07 18:20:48 driver-btm-api.c:132:stop_mining: stop mining: soc init failed!
2021-08-07 18:20:48 thread.c:698:cancel_read_nonce_reg_thread: cancel thread
2021-08-07 18:20:48 driver-btm-api.c:118:killall_hashboard: ****power off hashboard****
you need flash eeprom with code editor too.Chain[2] PIC init failed!
set_miner_status: ERROR_SOC_INIT
stop mining: soc init failed!
So replaced PIC chip with new, flashed a good hex onto it. I'm not sure what to look for next and appreciate any direction on next moves. Thank you.
Edit: I am running with just this board connected.
Code:
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203504K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25872K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12832K (cce79000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2669066886
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 9310506E-3F77-43CC-B7AB-7CFF20C05DA7, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 53/24, WL threshold: 4096, image sequence number: 121791118
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 15BA4C69-FA5C-4D1E-BF20-090C8AD78A1C, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-08-07 18:20:04 driver-btm-api.c:758:init_freq_mode: This is scan-user version
2021-08-07 18:20:04 driver-btm-api.c:1954:bitmain_soc_init: opt_multi_version = 1
2021-08-07 18:20:04 driver-btm-api.c:1955:bitmain_soc_init: opt_bitmain_ab = 1
2021-08-07 18:20:04 driver-btm-api.c:1956:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-08-07 18:20:04 driver-btm-api.c:1957:bitmain_soc_init: Miner compile time: Tue Aug 20 10:37:07 CST 2019 type: Antminer S17 Pro
2021-08-07 18:20:04 driver-btm-api.c:1958:bitmain_soc_init: commit version: 4b64fd6 2019-08-19 22:09:12, build by: lol 2019-08-20 10:47:29
2021-08-07 18:20:04 driver-btm-api.c:1776:show_sn: no SN got, please write SN to /nvdata/sn
2021-08-07 18:20:04 driver-btm-api.c:1236:miner_device_init: Detect 256MB control board of XILINX
2021-08-07 18:20:04 driver-btm-api.c:1184:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-08-07 18:20:04 thread.c:653:create_read_nonce_reg_thread: create thread
2021-08-07 18:20:10 driver-btm-api.c:1168:init_miner_version: miner ID : 8164ac2e57408854
2021-08-07 18:20:10 driver-btm-api.c:1174:init_miner_version: FPGA Version = 0xB013
2021-08-07 18:20:11 driver-btm-api.c:820:get_product_id: product_id[2] = 0
2021-08-07 18:20:11 driver-btm-api.c:771:_set_project_type: project:0
2021-08-07 18:20:11 driver-btm-api.c:796:_set_project_type: Project type: Antminer S17 Pro
2021-08-07 18:20:11 driver-btm-api.c:807:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
2021-08-07 18:20:11 driver-btm-api.c:808:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
2021-08-07 18:20:15 driver-btm-api.c:1877:bitmain_board_init: Fan check passed.
2021-08-07 18:20:26 driver-btm-api.c:309:init_pic: Chain[2] PIC init failed!
2021-08-07 18:20:26 driver-btm-api.c:191:set_miner_status: ERROR_PIC_LOST
2021-08-07 18:20:26 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-08-07 18:20:48 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xff
2021-08-07 18:20:48 driver-btm-api.c:191:set_miner_status: ERROR_SOC_INIT
2021-08-07 18:20:48 driver-btm-api.c:132:stop_mining: stop mining: soc init failed!
2021-08-07 18:20:48 thread.c:698:cancel_read_nonce_reg_thread: cancel thread
2021-08-07 18:20:48 driver-btm-api.c:118:killall_hashboard: ****power off hashboard****
Re: Can I safely run my S17+ hashboard with 2 missing heatsinks - long term
⭐ Merited by mikeywith (4)
Two of my chips got stuck to the heatsink when it dropped, whilst im arranging it to be repaired, can I safely run the board?
Pics
https://i.postimg.cc/mBZPwtHs/20220330-122238.jpg
https://i.postimg.cc/QMgjqQ3w/20220330-122244.jpg
Pics
https://i.postimg.cc/mBZPwtHs/20220330-122238.jpg
https://i.postimg.cc/QMgjqQ3w/20220330-122244.jpg
when your hash board temp rises your control board kill hash board and stop mining or restart s17+ because bad core or high temp.
your hash board have 4 temp sensor and read your temp from every chip and send average temp to control board.
when your hit sink on chip lost, your chip warming deadly and your fans can't get cool your chip, cause your hash board didn't damaged control board power off hash board or restart to hash boards get cooler.
that work only 5-10 min.
better way replace your asics and put your hit sink on chip with solder in s17+.
2022-03-31 17:35:10 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[2]: find 58 asic, times 0
https://i.postimg.cc/wBG9X4LK/AM-aaa-boards.png
Hihttps://i.postimg.cc/wBG9X4LK/AM-aaa-boards.png
your Hash board on chain 2 after get warm, only detect 58 asic and you need to reball chip 59, better reball 58 and 59. just be careful your heat didn't harm around asics and hit sinks.
⭐ Merited by Hache (1)
I was cleaning my hasboards and dropped one of them, the impact caused two heatsinks to fall off.
I have attached two pictures.
How do I go about cleaning the current heatsink and hashboard chip prior to correcting?
Which thermal paste is considered the best for this job?
https://i.postimg.cc/mBZPwtHs/20220330-122238.jpg
https://i.postimg.cc/QMgjqQ3w/20220330-122244.jpg
Hi,I have attached two pictures.
How do I go about cleaning the current heatsink and hashboard chip prior to correcting?
Which thermal paste is considered the best for this job?
https://i.postimg.cc/mBZPwtHs/20220330-122238.jpg
https://i.postimg.cc/QMgjqQ3w/20220330-122244.jpg
your asics failed and can't use solder to place your hit sink on chip.
You need to replace with new asic BM1397AG or BM1397AI and need Stencil for chip.
Then use a little solder on chip or hit sink and then put hit sink on chip with heater and make sure solder between chip and hit sink totally melted.
if your board is running well and you cant replace your asics you can put your hit sink by kafuter 704 but this isn't recommended way and after some day or month your bord severely damaged.
Same as My trouble
How do you repair it ?
your log is mean No voltage in Domain 7 (Column
but mine is No Voltage in Last Domain 12 (Column 11)
i Change LDO 8 pin and LDO 4 Pin still Not working
how about you
How do you repair it ?
your log is mean No voltage in Domain 7 (Column
but mine is No Voltage in Last Domain 12 (Column 11)
i Change LDO 8 pin and LDO 4 Pin still Not working
how about you
do you changed your control board?
before change that make sure your flats are healthy.
I search a bit and found PIC16F1704.hex but I don't know if this pic file will work because this pic file is dumped from the L3+ hashboard.
You can check the link below. If you are going to use this firmware to try make sure to backup or dump the original hex file first so that you can restore it in the future if it didn't work.
- https://bitcointalk.org/index.php?topic=2383200.msg24343142#msg24343142
Or try to dump the original hex file and flash it with your backup and maybe it can fix your issue.
Do you mind posting the kernel logs here I just curious on how did you know that it was a PIC issue.
You can check the link below. If you are going to use this firmware to try make sure to backup or dump the original hex file first so that you can restore it in the future if it didn't work.
- https://bitcointalk.org/index.php?topic=2383200.msg24343142#msg24343142
Or try to dump the original hex file and flash it with your backup and maybe it can fix your issue.
Do you mind posting the kernel logs here I just curious on how did you know that it was a PIC issue.
thank you
I found other healthy hash board and dump pic file from that.
I used t17+ pic file before and didn't work.
If you have the pickit that is needed to flash the firmware, then you can also read the firmware out of one of your other boards. No need to buy it.
https://i.imgur.com/kvjgjNR.png
https://i.imgur.com/kvjgjNR.png
thanks,
I have Pickit 4 but didn"t have any healthy S17+ Hash board.
Why not backup the PIC file from another known working hashboard?
Anyway, try to contact this thierry4wd he might be able to give you a copy of the pic file for this unit.
If not, then you can buy the pic file from zeusBTC here https://www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=220
Anyway, try to contact this thierry4wd he might be able to give you a copy of the pic file for this unit.
If not, then you can buy the pic file from zeusBTC here https://www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=220
cuz i don't have any s17+ Hash Board and 3 of them pic's and drivers failed.
thanks.