Hi all,

I tried updating to Braiins via the NAND SD loader, but now nothing works, including any network connection and factory SD firmware update. I have attached a startup log from the serial port; is there anything I can to to get the control board functional again?

Thanks

Code:

U-Boot SPL 2016.03-g8728fee00a (Dec 05 2020 - 17:42:30)
Trying to boot from NAND

U-Boot 2016.03-gcaca2524a4 (Dec 11 2020 - 16:58:19 +0000)

Model: Antminer S17 Miner Control Board
Board: Xilinx Zynq
DRAM: ECC disabled 256 MiB
NAND: 256 MiB
MMC: sdhci@e0100000: 0
In: serial@e0000000
Out: serial@e0000000
Err: serial@e0000000
Model: Antminer S17 Miner Control Board
Board: Xilinx Zynq
Boot: NAND
Net: ZYNQ GEM: e000b000, phyaddr 7, interface rgmii-id
PHY is not detected
GEM PHY init failed
eth0: ethernet@e000b000
Hit any key to stop autoboot: 0
Copying FIT from NAND flash to RAM...
Card did not respond to voltage select!
** Bad device mmc 0 **

NAND read: device 0 offset 0x300000, size 0x100000
1048576 bytes read: OK
Uncompressed size: 2083859 = 0x1FCC13
design filename = "system_wrapper;UserID=0XFFFFFFFF;Version=2017.4_AR70455"
part number = "7z007sclg225"
date = "2020/12/04"
time = "16:06:03"
bytes in bitstream = 2083740
zynq_align_dma_buffer: Align buffer at 2100077 to 2100000(swap 1)
gpio: pin 37 (gpio 37) value is 1
gpio: pin 36 (gpio 36) value is 1
gpio: pin 36 (gpio 36) value is 0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=7", size 95 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 760, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 17 69581814
ubi0: available PEBs: 0, total reserved PEBs: 760, PEBs reserved for bad PEB han dling: 40
Read 0 bytes from volume kernel to 2000000
No size specified -> Using max size (2920448)
gpio: pin 36 (gpio 36) value is 1
## Loading kernel from FIT Image at 02000000 ...
Using 'config@1' configuration
Verifying Hash Integrity ... OK
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.4.92
Type: Kernel Image
Compression: uncompressed
Data Start: 0x020000e4
Data Size: 2828176 Bytes = 2.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00008000
Entry Point: 0x00008000
Hash algo: crc32
Hash value: 883a4f29
Hash algo: sha1
Hash value: 097a2def90380b20ff7d88fb4e67ef0085c5f976
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 02000000 ...
Using 'config@1' configuration
Trying 'fdt@1' fdt subimage
Description: ARM OpenWrt am2-s17 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x022b29a8
Data Size: 15638 Bytes = 15.3 KiB
Architecture: ARM
Hash algo: crc32
Hash value: d09638b7
Hash algo: sha1
Hash value: ca688998e39bf45f32375d43b69008e3ea246caa
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x22b29a8
Loading Kernel Image ... OK
Loading Device Tree to 07ff9000, end 07fffd15 ... OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.0-xilinx-g518c00cd977f-dirty (build@runner-pege gjka-project-312-concurrent-1) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3560-79f57e42 2d) ) #0 SMP PREEMPT Tue Oct 5 05:59:32 2021
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] Machine model: Antminer S17 Miner Control Board
[ 0.000000] cma: Reserved 16 MiB at 0x0f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cedca000 s18944 r8192 d22016 u4915 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 65024
[ 0.000000] Kernel command line: console=ttyPS0,115200 noinitrd ubi.mtd=7 ubi .block=0,1 root=/dev/ubiblock0_1 r rootfstype=squashfs rootwait mtdparts=pl35x-n and:512k(boot),2560k(uboot),2m(fpga1),2m(fpga2),512k(uboot_env),512k(miner_cfg), 22m(recovery),95m(firmware1),95m(firmware2),36m(factory) earlyprintk
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 235148K/262144K available (5572K kernel code, 204K rwdata , 1844K rodata, 260K init, 221K bss, 10612K reserved, 16384K cma-reserved, 0K hi ghmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0746524 (7418 kB)
[ 0.000000] .init : 0xc0747000 - 0xc0788000 ( 260 kB)
[ 0.000000] .data : 0xc0788000 - 0xc07bb2a0 ( 205 kB)
[ 0.000000] .bss : 0xc07bb2a0 - 0xc07f29c4 ( 222 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] slcr mapped to d0800000
[ 0.000000] L2C: platform modifies aux control register: 0x02060000 -> 0x3246 0000
[ 0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x3 2460000
[ 0.000000] L2C-310 erratum 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x46460001
[ 0.000000] zynq_clock_init: clkc starts at d0800100
[ 0.000000] Zynq clock init
[ 0.000011] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 43980 46511103ns
[ 0.000035] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycle s: 0x4ce07af025, max_idle_ns: 440795209040 ns
[ 0.000137] clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, ma x_idle_ns: 537538477 ns
[ 0.000167] timer #0 at d0808000, irq=17
[ 0.000534] Console: colour dummy device 80x30
[ 0.000556] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090309] pid_max: default: 32768 minimum: 301
[ 0.090413] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090924] CPU: Testing write buffer coherency: ok
[ 0.091130] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.091221] Setting up static identity map for 0x8280 - 0x82d8
[ 0.260297] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260372] Brought up 2 CPUs
[ 0.260391] SMP: Total of 2 processors activated (2664.03 BogoMIPS).
[ 0.260399] CPU: All CPU(s) started in SVC mode.
[ 0.265192] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.265614] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.266519] pinctrl core: initialized pinctrl subsystem
[ 0.267878] NET: Registered protocol family 16
[ 0.269929] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.300414] cpuidle: using governor ladder
[ 0.330284] cpuidle: using governor menu
[ 0.343098] zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xd0880000
[ 0.343534] zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
[ 0.382352] GPIO IRQ not connected
[ 0.382371] XGpio: /amba_pl/gpio@41200000: registered, base is 902
[ 0.382554] GPIO IRQ not connected
[ 0.382566] XGpio: /amba_pl/gpio@41210000: registered, base is 897
[ 0.382812] XGpio: /amba_pl/gpio@41220000: registered, base is 895
[ 0.383660] vgaarb: loaded
[ 0.384160] SCSI subsystem initialized
[ 0.384636] usbcore: registered new interface driver usbfs
[ 0.384734] usbcore: registered new interface driver hub
[ 0.384837] usbcore: registered new device driver usb
[ 0.385595] i2c-gpio amba_pl:i2c-psu: using pins 895 (SDA) and 896 (SCL)
[ 0.385669] media: Linux media interface: v0.10
[ 0.385750] Linux video capture interface: v2.00
[ 0.385843] pps_core: LinuxPPS API ver. 1 registered
[ 0.385855] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
[ 0.385903] PTP clock support registered
[ 0.386006] EDAC MC: Ver: 3.0.0
[ 0.386754] Advanced Linux Sound Architecture Driver Initialized.
[ 0.388018] clocksource: Switched to clocksource arm_global_timer
[ 0.397833] NET: Registered protocol family 2
[ 0.398818] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.398859] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.398908] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.398959] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.398991] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.399217] NET: Registered protocol family 1
[ 0.399578] RPC: Registered named UNIX socket transport module.
[ 0.399590] RPC: Registered udp transport module.
[ 0.399599] RPC: Registered tcp transport module.
[ 0.399607] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.401181] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.411859] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.424332] io scheduler noop registered
[ 0.424356] io scheduler deadline registered
[ 0.424411] io scheduler cfq registered (default)
[ 0.426362] dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.426382] dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num _Peri-4 Num_Events-16
[ 0.427105] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.428559] e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 143, base_baud = 6249999) is a xuartps
[ 1.070537] console [ttyPS0] enabled
[ 1.074700] xdevcfg f8007000.devcfg: ioremap 0xf8007000 to d0826000
[ 1.081428] [drm] Initialized drm 1.1.0 20060810
[ 1.096776] brd: module loaded
[ 1.105853] loop: module loaded
[ 1.111897] CAN device driver interface
[ 1.117489] libphy: MACB_mii_bus: probed
[ 1.198153] macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000 b000 irq 145 (cc:e0:bf:8c:07:1a)
[ 1.208028] macb e000b000.ethernet eth0: attached PHY driver [Generic PHY] (m ii_bus:phy_addr=e000b000.etherne:00, irq=-1)
[ 1.219253] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.224999] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.236511] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.243003] ehci-pci: EHCI PCI platform driver
[ 1.247571] usbcore: registered new interface driver usb-storage
[ 1.255068] mousedev: PS/2 mouse device common for all mice
[ 1.271006] i2c /dev entries driver
[ 1.278307] EDAC MC: ECC not enabled
[ 1.282071] Xilinx Zynq CpuIdle Driver started
[ 1.286812] sdhci: Secure Digital Host Controller Interface driver
[ 1.292943] sdhci: Copyright(c) Pierre Ossman
[ 1.297255] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.303269] sdhci-arasan e0100000.mmc: No vmmc regulator found
[ 1.309046] sdhci-arasan e0100000.mmc: No vqmmc regulator found
[ 1.349069] mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA
[ 1.357041] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.363442] usbcore: registered new interface driver usbhid
[ 1.368961] usbhid: USB HID core driver
[ 1.373718] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.380019] nand: Micron MT29F2G08ABAEAWP
[ 1.383978] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64
[ 1.391554] nand: WARNING: pl35x-nand: the ECC used on your system is too wea k compared to the one required by the NAND chip
[ 1.403024] Bad block table found at page 131008, version 0x01
[ 1.409249] Bad block table found at page 130944, version 0x01
[ 1.415257] nand_read_bbt: bad block at 0x00000cb00000
[ 1.420393] 10 cmdlinepart partitions found on MTD device pl35x-nand
[ 1.426664] Creating 10 MTD partitions on "pl35x-nand":
[ 1.431895] 0x000000000000-0x000000080000 : "boot"
[ 1.437719] 0x000000080000-0x000000300000 : "uboot"
[ 1.443524] 0x000000300000-0x000000500000 : "fpga1"
[ 1.449314] 0x000000500000-0x000000700000 : "fpga2"
[ 1.465059] 0x000000700000-0x000000780000 : "uboot_env"
[ 1.481218] 0x000000780000-0x000000800000 : "miner_cfg"
[ 1.497334] 0x000000800000-0x000001e00000 : "recovery"
[ 1.513556] 0x000001e00000-0x000007d00000 : "firmware1"
[ 1.520352] 0x000007d00000-0x00000dc00000 : "firmware2"
[ 1.537099] 0x00000dc00000-0x000010000000 : "factory"
[ 1.555955] nf_conntrack version 0.5.0 (3930 buckets, 15720 max)
[ 1.563749] NET: Registered protocol family 10
[ 1.569396] sit: IPv6 over IPv4 tunneling driver
[ 1.574723] NET: Registered protocol family 17
[ 1.579171] bridge: automatic filtering via arp/ip/ip6tables has been depreca ted. Update your scripts to load br_netfilter if you need this.
[ 1.591721] can: controller area network core (rev 20120528 abi 9)
[ 1.597922] NET: Registered protocol family 29
[ 1.602309] can: raw protocol (rev 20120528)
[ 1.606540] can: broadcast manager protocol (rev 20120528 t)
[ 1.612211] can: netlink gateway (rev 20130117) max_hops=1
[ 1.617870] 8021q: 802.1Q VLAN Support v1.8
[ 1.622393] Registering SWP/SWPB emulation handler
[ 1.628719] ubi0: attaching mtd7
[ 1.978371] ubi0: scanning is finished
[ 1.989776] ubi0: attached mtd7 (name "firmware1", size 95 MiB)
[ 1.995614] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.002497] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.009262] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.016184] ubi0: good PEBs: 760, bad PEBs: 0, corrupted PEBs: 0
[ 2.022187] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 12 8
[ 2.029398] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequ ence number: 1769581814
[ 2.038506] ubi0: available PEBs: 0, total reserved PEBs: 760, PEBs reserved for bad PEB handling: 40
[ 2.047707] ubi0: background thread "ubi_bgt0d" started, PID 845
[ 2.058738] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.064161] hctosys: unable to open rtc device (rtc0)
[ 2.073707] ALSA device list:
[ 2.076594] No soundcards found.
[ 2.082827] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.090268] Freeing unused kernel memory: 260K (c0747000 - c0788000)
[ 2.564783] init: Console is alive
[ 2.568304] init: - watchdog -
[ 2.971920] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.067328] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.076042] init: - preinit -
[ 3.683664] random: jshn urandom read with 0 bits of entropy available
[ 3.885416] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.198209] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[ 5.206311] macb e000b000.ethernet eth0: link up (100/Full)
[ 5.211899] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.048135] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 918
[ 7.072841] UBIFS (ubi0:2): recovery needed
▒[ 7.146695] UBIFS (ubi0:2): recovery completed
[ 7.151170] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data"
[ 7.158937] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 7.168828] UBIFS (ubi0:2): FS size: 72122368 bytes (68 MiB, 568 LEBs), journ al size 3555328 bytes (3 MiB, 28 LEBs)
[ 7.179239] UBIFS (ubi0:2): reserved for root: 3406517 bytes (3326 KiB)
[ 7.185829] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID BE0B2 0A5-CF46-4440-B4EE-6D050D517E05, small LPT model
[ 7.198885] mount_root: switching to ubifs overlay
[ 7.213715] urandom-seed: Seeding with /etc/urandom.seed
[ 7.340236] procd: - early -
[ 7.343093] procd: - watchdog -
[ 7.992516] procd: - watchdog -
[ 7.995798] procd: - ubus -
[ 8.217208] macb e000b000.ethernet eth0: link down
[ 8.223198] procd: - init -
Please press Enter to activate this console.
[ 8.542050] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.620910] tun: Universal TUN/TAP device driver, 1.6
[ 8.625885] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.635076] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.647491] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.779516] xt_time: kernel timezone is -0000
[ 8.789985] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.740385] device eth0 entered promiscuous mode
[ 11.750687] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 11.853615] Start post-upgrade process...
[ 12.218235] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[ 12.226343] macb e000b000.ethernet eth0: link up (100/Full)
[ 12.247029] br-lan: port 1(eth0) entered forwarding state
[ 12.252436] br-lan: port 1(eth0) entered forwarding state
[ 12.273054] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 12.627356] random: nonblocking pool is initialized
[ 13.421492] Detecting miner model...
[ 14.248176] br-lan: port 1(eth0) entered forwarding state
[ 15.797518] Oct 13 18:07:27.359 WARN main bosminer_plus_am2_s17: Parsing con fig failed with: configuration parsing failed: missing field `format`, using def ault config
[ 15.816823] Oct 13 18:07:27.378 WARN main bosminer_plus_am2_s17: Failed to g et descriptor: missing model specification, using default descriptor Antminer S1 7
[ 20.433527] Oct 13 18:07:31.995 INFO main bosminer_plus_am2_s17: Detected Ha sh Board #0:
[ 20.433527] +--------------------+-------------------------+
[ 20.433527] |S/N |YDFTYH9AIABBD0AHZ |
[ 20.433527] |BOM version |01.00 |
[ 20.433527] |PCB version |01.10 |
[ 20.433527] |Voltage (Avg.) |17.80 V |
[ 20.433527] |Frequency (Avg.) |625 MHz |
[ 20.433527] |Hashrate |18638.00 GH/s |
[ 20.433527] +--------------------+-------------------------+
[ 20.433527]
[ 20.489914] Oct 13 18:07:32.052 INFO main bosminer_plus_am2_s17: Detected Ha sh Board #1:
[ 20.489914] +--------------------+-------------------------+
[ 20.489914] |S/N |YDFTYH9AIABBD0AHZ |
[ 20.489914] |BOM version |01.00 |
[ 20.489914] |PCB version |01.10 |
[ 20.489914] |Voltage (Avg.) |17.80 V |
[ 20.489914] |Frequency (Avg.) |625 MHz |
[ 20.489914] |Hashrate |18638.00 GH/s |
[ 20.489914] +--------------------+-------------------------+
[ 20.489914]
[ 20.546336] Oct 13 18:07:32.108 INFO main bosminer_plus_am2_s17: Detected Ha sh Board #2:
[ 20.546336] +--------------------+-------------------------+
[ 20.546336] |S/N |YDFTYH9AIABBD0AHZ |
[ 20.546336] |BOM version |01.00 |
[ 20.546336] |PCB version |01.10 |
[ 20.546336] |Voltage (Avg.) |17.80 V |
[ 20.546336] |Frequency (Avg.) |625 MHz |
[ 20.546336] |Hashrate |18638.00 GH/s |
[ 20.546336] +--------------------+-------------------------+
[ 20.546336]
[ 20.603218] Antminer T17e

Cococarbine

Posts

Merits