Quote from: v0n on August 11, 2014, 11:34:35 AM

Your blades are not starting up, check Status->System Log and Status-> Kernel Log for errors, but it's most likely not enough power on +12V rail from PSU to start mining. Try connecting both PCI-e cables to only one blade (the one with controller, you'll know quickly which one is which - blade without controller will spin fans full blast after about 10 seconds, whereas the one with controller, providing HTTP access will properly control fan speed and produce web access to the interface )

Keep in mind, that in screenshot below the system is up for only 25 seconds, that's not enough time for blades/chips to start mining.

And just as a side note, using the same pool for all three entries will not offer any load balancing or fail over.

Thanks for your response.

Please check the below Kernel Log details and let me know the solution. Very Appreciated.

================================================================================

[ 0.000000] Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #140 Mon Jul 21 17:27:04 CST 2014
[ 0.000000] MyLoader: sysp=1bec2fee, boardp=fdd6ef6f, parts=fc031564
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803005b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.100000] MAC FF:FF:FF:FF:FF:FF
[ 0.100000] MAC 20:59:a0:c3:d6:ee
[ 0.560000] bio: create slab at 0
[ 0.560000] Switching to clocksource MIPS
[ 0.570000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.580000] TCP: Hash tables configured (established 512 bind 512)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] NET: Registered protocol family 1
[ 0.610000] PCI: CLS 0 bytes, default 32
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.640000] msgmni has been set to 119
[ 0.650000] io scheduler noop registered
[ 0.650000] io scheduler deadline registered (default)
[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.670000] console [ttyATH0] enabled, bootconsole disabled
[ 0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.690000] m25p80 spi0.0: found gd25q64, expected m25p80
[ 0.690000] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 0.700000] 5 tp-link partitions found on MTD device spi0.0
[ 0.700000] Creating 5 MTD partitions on "spi0.0":
[ 0.710000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.710000] 0x000000020000-0x000000117db8 : "kernel"
[ 0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.730000] 0x000000117db8-0x0000007f0000 : "rootfs"
[ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.750000] mtd: partition "rootfs" set to be root filesystem
[ 0.750000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
[ 0.760000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[ 0.770000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.770000] 0x0000007f0000-0x000000800000 : "art"
[ 0.790000] libphy: ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.350000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.390000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.940000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 2.950000] TCP: cubic registered
[ 2.950000] NET: Registered protocol family 17
[ 2.960000] 8021q: 802.1Q VLAN Support v1.8
[ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.980000] Freeing unused kernel memory: 232K (80316000 - 80350000)
[ 5.740000] usbcore: registered new interface driver usbfs
[ 5.740000] usbcore: registered new interface driver hub
[ 5.750000] usbcore: registered new device driver usb
[ 5.760000] usbcore: registered new interface driver bitmain
[ 5.760000] hash ok
[ 5.760000] hashtest OK
[ 5.770000] bitmain-asic: success to register device
[ 5.770000] usbcore: registered new interface driver bitmainbl
[ 5.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.790000] ehci-platform: EHCI generic platform driver
[ 5.790000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.800000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.810000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.830000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.830000] hub 1-0:1.0: USB hub found
[ 5.830000] hub 1-0:1.0: 1 port detected
[ 6.170000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.320000] hub 1-1:1.0: USB hub found
[ 6.320000] hub 1-1:1.0: 2 ports detected
[ 6.610000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[ 6.740000] bitmainbl 1-1.1:1.0: USB Bitmain bootloader device now attached to USB Bitmain bootloader-0
[ 6.750000] PIC microchip bootloader usb OK
[ 10.500000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 17 of xref (0 dead, 2 orphan) found.
[ 13.020000] hidraw: raw HID events driver (C) Jiri Kosina
[ 13.020000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 13.030000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 13.040000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
[ 13.070000] usbcore: registered new interface driver usbhid
[ 13.070000] usbhid: USB HID core driver
[ 13.080000] usbcore: registered new interface driver usbserial
[ 13.090000] usbcore: registered new interface driver usbserial_generic
[ 13.090000] usbserial: USB Serial support registered for generic
[ 13.120000] xt_time: kernel timezone is -0000
[ 13.160000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.160000] cfg80211: World regulatory domain updated:
[ 13.170000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.170000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.180000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.190000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.220000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.350000] ath: EEPROM regdomain: 0x0
[ 13.350000] ath: EEPROM indicates default country code should be used
[ 13.350000] ath: doing EEPROM country->regdmn map search
[ 13.350000] ath: country maps to regdmn code: 0x3a
[ 13.350000] ath: Country alpha2 being used: US
[ 13.350000] ath: Regpair used: 0x3a
[ 13.360000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.370000] cfg80211: Calling CRDA for country: US
[ 13.370000] cfg80211: Regulatory domain changed to country: US
[ 13.380000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.390000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 13.390000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 13.400000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.410000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.420000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.430000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 13.430000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 18.340000] device eth0 entered promiscuous mode
[ 21.340000] eth1: link up (100Mbps/Full duplex)
[ 21.670000] no int in filled

================================================================================

logicuser

Posts

Merits