Quote from: Plumpkatt1 on January 04, 2016, 12:31:13 AM

Sure is strange how that helps but it does. My controller that I thought was bad I got it to boot eventually using an sd card. Then I let it mine for 2 weeks and the controller seems to be good again. Sometimes it glitches and I do an SD Boot or recovery and it is then good again. If I could just get the loop 3 to come up again I'd be a happy camper but I cant. So for now my sp20 mines at 1-1.1TH and is pulling about 670 watts. I used the command vi /etc/mg_max_asic_temp and entered 7 to set the max temp to 120c instead of 125c and I am getting much better/stable results.

Using Putty/SSH I log into my miner and enter vi /etc/mg_custom_mode.

I then hit the insert button which allows me to edit the configuration. Right below is what I am using for my settings:

Code:

FAN:05 VS0:700 VS1:700 VS2:700 VS3:700 VMAX:710 AC0:288 AC1:288 AC2:288 AC3:288 DC_AMP:170

I then hit the esc button. Then I enter :wq and hit enter to save the config. Then I hit restart minergate on the web gui to have the changes to take effect. Below is a screenshot of the results when looking at the ASIC Stats on the miners web gui. I chose the fan to be at speed of 05 because if I have it any higher it starts a fight with me and my wife.

[...]

looks cool do you think it will help my miner are you in the uk?

Code:

2.6.14
Uptime:58944 | FPGA ver:100 | BIST in 67
-----BOARD-0-----
PSU[UNKNOWN]: 0->(284w/284w)[284 284 284] (->284w[284 284 284]) (lim=288) 0c 414GH cooling:0/0xc0
-----BOARD-1-----
PSU[UNKNOWN]: 0->(5w/5w)[5 5 5] (->5w[5 5 5]) (lim=288) 0c 0GH cooling:0/0xc0
-----BOARD-2-----
PSU[UNKNOWN]: 0->(146w/146w)[146 146 146] (->146w[146 146 146]) (lim=288) 0c 210GH cooling:0/0xc0
-----BOARD-3-----
PSU[UNKNOWN]: 0->(254w/254w)[254 254 254] (->254w[254 254 254]) (lim=288) 0c 387GH cooling:0/0xc0
LOOP[0] ON TO:0 (w:5568)
0: DC2DC/1/:[vlt1:738 vlt2:743(DCl:794 Tl:794 Ul:789) 111W 150A 59c] ASIC:[ 85c (125c) 1060hz(BL:1060) 2701 (E:193) F:0 L:0]
1: DC2DC/1/:[vlt1:742 vlt2:746(DCl:794 Tl:794 Ul:789) 119W 159A 74c] ASIC:[110c (125c) 1090hz(BL:1090) 2867 (E:192) F:0 L:0]
LOOP[1] OFF TO:0 (test serial failed)
2: disabled (serial problem)
3: disabled (serial problem)
LOOP[2] ON TO:0 (w:2817)
4: disabled (User disabled)
5: DC2DC/1/:[vlt1:742 vlt2:743(DCl:743 Tl:794 Ul:789) 117W 157A 71c] ASIC:[105c (125c) 1090hz(BL:1090) 2817 (E:193) F:0 L:0]
LOOP[3] ON TO:0 (w:5184)
6: DC2DC/1/:[vlt1:710 vlt2:717(DCl:794 Tl:717 Ul:789) 101W 140A 76c] ASIC:[120c (125c) 1000hz(BL:1000) 2533 (E:193) F:0 L:0]
7: DC2DC/1/:[vlt1:705 vlt2:709(DCl:794 Tl:709 Ul:789) 104W 147A 81c] ASIC:[120c (125c) 1010hz(BL:1010) 2651 (E:193) F:0 L:0]

[H:HW:1013Gh (100),DC-W:553,L:0,A:5,MMtmp:0 TMP:(20/20)=>=>=>(31/31 , 57/57)]
Pushed 10 jobs , in HW queue 4 jobs (sw:3, hw:3)!
min:17 wins:13569[this/last min:2/14] bist-fail:331, hw-err:10
leading-zeroes:42 idle promils[s/m]:0/5, rate:978gh/s asic-count:905 (wins:1+1)
wall watts:756
Fan:90, conseq:200
AC2DC BAD: 0 0
R/NR: 1658/0
RTF asics: 0
FET: 0:9 1:9
4 restarted 0 reset 0 reset2 0 fake_wins
0 stuck_bist 0 low_power 0 stuck_pll 0 runtime_dsble
0 purge_queue 0 read_timeouts 0 dc2dc_i2c 1 read_tmout2 0 read_crptn
0 purge_queue3 0 bad_idle
0 err_murata
Adapter queues: rsp=0, req=25