Quote from: rwwilson75 on December 18, 2016, 12:36:11 AM

Quote

I apologize. Is that the pound symbol that says code or is there another way? Do you have any helpful input as far as why the miner appears to be OK as far as status lights but is not hashing?

the new firmware can't work if one of your boards have an issue
so just remove data cable from one board at a time and open your machine until you get the damaged one and you machine will work with 2 boards

I don't think its the boards all green lights are flashing normally and I have no xxx's in the ASIC status. It will hash for a little bit and then go to o hashing. I have had a bad board before and had it repaired this seems different. I just received this s9 yesterday. I shouldnt have to download new firmware should I? I don't know how to read kernal logs but one line I noticed said ethernet up link (1000/FULL).

Code:

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gf387dab-dirty (lzq@armdev01) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #38 SMP PREEMPT Fri Jun 17 20:02:51 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c06e4600, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=/dev/mtdblock1 rootfstype=jffs2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884528K/1032192K available (4764K kernel code, 271K rwdata, 1816K rodata, 200K init, 257K bss, 147664K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06752f8 (6581 kB)
[ 0.000000] .init : 0xc0676000 - 0xc06a8380 ( 201 kB)
[ 0.000000] .data : 0xc06aa000 - 0xc06edd00 ( 272 kB)
[ 0.000000] .bss : 0xc06edd0c - 0xc072e4fc ( 258 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000305] ps7-ttc #0 at f0006000, irq=43
[ 0.000607] Console: colour dummy device 80x30
[ 0.000644] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040206] pid_max: default: 32768 minimum: 301
[ 0.040421] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040442] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.042580] CPU: Testing write buffer coherency: ok
[ 0.042941] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043003] Setting up static identity map for 0x482448 - 0x4824a0
[ 0.043219] L310 cache controller enabled
[ 0.043239] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121027] CPU1: Booted secondary processor
[ 0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210358] Brought up 2 CPUs
[ 0.210376] SMP: Total of 2 processors activated.
[ 0.210385] CPU: All CPU(s) started in SVC mode.
[ 0.211052] devtmpfs: initialized
[ 0.213438] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214689] regulator-dummy: no parameters
[ 0.223310] NET: Registered protocol family 16
[ 0.225623] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.227935] cpuidle: using governor ladder
[ 0.227949] cpuidle: using governor menu
[ 0.235435] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.236968] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.236982] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237093] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.259020] bio: create slab at 0
[ 0.260750] vgaarb: loaded
[ 0.261996] SCSI subsystem initialized
[ 0.262885] usbcore: registered new interface driver usbfs
[ 0.263055] usbcore: registered new interface driver hub
[ 0.263298] usbcore: registered new device driver usb
[ 0.263825] media: Linux media interface: v0.10
[ 0.263983] Linux video capture interface: v2.00
[ 0.264226] pps_core: LinuxPPS API ver. 1 registered
[ 0.264238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.264362] PTP clock support registered
[ 0.264722] EDAC MC: Ver: 3.0.0
[ 0.265784] Advanced Linux Sound Architecture Driver Initialized.
[ 0.268742] DMA-API: preallocated 4096 debug entries
[ 0.268757] DMA-API: debugging enabled by kernel config
[ 0.268846] Switched to clocksource arm_global_timer
[ 0.289841] NET: Registered protocol family 2
[ 0.290522] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.290619] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.290778] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.290853] TCP: reno registered
[ 0.290870] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.290928] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.291200] NET: Registered protocol family 1
[ 0.291588] RPC: Registered named UNIX socket transport module.
[ 0.291601] RPC: Registered udp transport module.
[ 0.291610] RPC: Registered tcp transport module.
[ 0.291618] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.291632] PCI: CLS 0 bytes, default 64
[ 0.292087] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294160] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.295624] bounce pool size: 64 pages
[ 0.296533] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.296750] msgmni has been set to 1487
[ 0.297233] io scheduler noop registered
[ 0.297246] io scheduler deadline registered
[ 0.297284] io scheduler cfq registered (default)
[ 0.307872] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307892] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.434240] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.006732] console [ttyPS0] enabled
[ 1.011041] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.018702] [drm] Initialized drm 1.1.0 20060810
[ 1.035762] brd: module loaded
[ 1.045262] loop: module loaded
[ 1.055033] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.060896] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.068679] libphy: XEMACPS mii bus: probed
[ 1.073088] ------------- phy_id = 0x3625e62
[ 1.077836] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.086553] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.093213] ehci-pci: EHCI PCI platform driver
[ 1.100635] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.107454] usbcore: registered new interface driver usb-storage
[ 1.114382] mousedev: PS/2 mouse device common for all mice
[ 1.120523] i2c /dev entries driver
[ 1.127428] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.132972] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.138887] Xilinx Zynq CpuIdle Driver started
[ 1.143745] sdhci: Secure Digital Host Controller Interface driver
[ 1.149888] sdhci: Copyright(c) Pierre Ossman
[ 1.154182] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.161013] mmc0: no vqmmc regulator found
[ 1.165027] mmc0: no vmmc regulator found
[ 1.208883] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.217568] usbcore: registered new interface driver usbhid
[ 1.223088] usbhid: USB HID core driver
[ 1.227834] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.234126] nand: Micron MT29F2G08ABAEAWP
[ 1.238095] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.244123] Bad block table found at page 131008, version 0x01
[ 1.250539] Bad block table found at page 130944, version 0x01
[ 1.256683] 4 ofpart partitions found on MTD device pl353-nand
[ 1.262458] Creating 4 MTD partitions on "pl353-nand":
[ 1.267558] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.275637] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.283018] 0x00000b000000-0x00000ec00000 : "upgrade-rootfs"
[ 1.290123] 0x00000ec00000-0x000010000000 : "upgrade-tmp"
[ 1.298798] TCP: cubic registered
[ 1.302069] NET: Registered protocol family 17
[ 1.306715] Registering SWP/SWPB emulation handler
[ 1.312371] regulator-dummy: disabling
[ 1.316176] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.326590] ALSA device list:
[ 1.329523] No soundcards found.
[ 5.585234] VFS: Mounted root (jffs2 filesystem) on device 31:1.
[ 5.594255] devtmpfs: mounted
[ 5.597361] Freeing unused kernel memory: 200K (c0676000 - c06a8000)
[ 7.270427] random: dd urandom read with 1 bits of entropy available
[ 7.668870]
[ 7.668870] bcm54xx_config_init
[ 8.278860]
[ 8.278860] bcm54xx_config_init
[ 12.279718] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 12.285828] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 29.888333] In axi fpga driver!
[ 29.891403] request_mem_region OK!
[ 29.894792] AXI fpga dev virtual address is 0xf0112000
[ 29.899938] *base_vir_addr = 0x8c504
[ 29.919501] In fpga mem driver!
[ 29.922573] request_mem_region OK!
[ 29.926139] fpga mem virtual address is 0xf3000000
[ 31.338194]
[ 31.338194] bcm54xx_config_init
[ 31.978093]
[ 31.978093] bcm54xx_config_init
[ 35.978570] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 35.984674] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 84.887577] jffs2: warning: (1095) jffs2_do_read_inode_internal: Truncating ino #2068 to 19073 bytes failed because it only had 16032 bytes to start with!
[ 282.565855] random: nonblocking pool is initialized
use critical mode to search freq...
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x02
Check chain[6] PIC fw version=0x02
Check chain[7] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[27] has core num=1
Check chain[5] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[36] has core num=1
Check chain[6] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x02
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,-4,0,0,0,0,0,0
chain[6] temp offset record: 62,-4,0,0,0,0,0,0
chain[7] temp offset record: 62,-3,0,0,0,0,0,0
set command mode to VIL

singleBoardTest: AsicType = 1387

singleBoardTest: asicNum = 64

singleBoardTest: real AsicNum = 63

--- check asic number
set_baud=0, ought to be 1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[5]
disable_pic_dac on chain[6]
disable_pic_dac on chain[7]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
This is XILINX board.
Chain[J6] has backup chain_voltage=890
Chain[J6] test patten OK temp=78
Check chain[5] PIC fw version=0x02
Chain[J7] has backup chain_voltage=890
Chain[J7] test patten OK temp=73
Check chain[6] PIC fw version=0x02
Chain[J8] has backup chain_voltage=880
Chain[J8] test patten OK temp=70
Check chain[7] PIC fw version=0x02
Chain[J6] orignal chain_voltage=91 value=890
Chain[J7] orignal chain_voltage=91 value=890
Chain[J8] orignal chain_voltage=108 value=880
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[27] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[36] has core num=1
Chain[J8] has core num in PIC
miner total rate=13999GH/s fixed rate=13500GH/s
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:431
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:408 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:5 max freq=662
Chain:5 min freq=408

read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:350 Asic[18]:656 Asic[19]:643 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:512 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:681 Asic[48]:656
Asic[49]:656 Asic[50]:681 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=681
Chain:6 min freq=350

read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:468 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:416 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:656
Chain:7 max freq=662
Chain:7 min freq=416

Miner fix freq ...
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:431
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:408 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=408

read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:350 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:512 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=350

read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:468 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:416 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:7 max freq=643
Chain:7 min freq=416

max freq = 643
Chain[J6] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J8] PIC temp offset=62,-3,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-3 typeID=55
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
Chain[J6] set opencore voltage=920 [40]
Chain[J6] set working voltage=890 [91]
Chain[J7] set opencore voltage=920 [40]
Chain[J7] set working voltage=890 [91]
Chain[J8] set opencore voltage=920 [40]
Chain[J8] set working voltage=880 [108]
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
do heat board 8xPatten for 1 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=911 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=911
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=911 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[10]=911
core[107]=7

asic[18]=911
core[089]=7

asic[19]=911
core[064]=7

asic[46]=911
core[055]=7

asic[47]=911
core[055]=7

asic[60]=911
core[007]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:51502
last_nonce_num:35641
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=911 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=911 asic[12]=912 asic[13]=911 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=911 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=911 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=911 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=911 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=911 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[05]=911
core[061]=7

asic[10]=911
core[019]=7

asic[11]=911
core[019]=7

asic[13]=911
core[067]=7

asic[14]=911
core[063]=7

asic[21]=911
core[083]=7

asic[25]=911
core[030]=7

asic[30]=911
core[037]=7

asic[37]=911
core[052]=7

asic[52]=911
core[005]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57446
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44368
last_nonce_num:37018
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=911 asic[20]=911 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=911 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[12]=911
core[092]=7

asic[14]=911
core[094]=7

asic[19]=911
core[057]=7

asic[20]=911
core[053]=7

asic[26]=911
core[035]=7

asic[48]=911
core[040]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50456
last_nonce_num:33309
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
do heat board 8xPatten for 2 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[10]=911
core[059]=7

asic[15]=911
core[029]=7

asic[46]=911
core[063]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:49422
last_nonce_num:32058
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=911
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=911 asic[14]=912 asic[15]=912
asic[16]=911 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=911 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=911 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[07]=911
core[030]=7

asic[13]=911
core[041]=7

asic[16]=911
core[112]=7

asic[22]=911
core[070]=7

asic[57]=911
core[055]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50461
last_nonce_num:31431
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=911 asic[02]=910 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=911 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912

Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[01]=911
core[092]=7

asic[02]=910
core[046]=7 core[092]=7

asic[12]=911
core[006]=7

asic[15]=911
core[057]=7

asic[18]=911
core[066]=7

asic[26]=911
core[031]=7

asic[51]=911
core[110]=7

freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643

total valid nonce number:57448
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44345
last_nonce_num:31732
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
restartNum = 2 , auto-reinit enabled...
Chain[5] Chip[62] TempTypeID=55 middle offset=-4
Chain[5] Chip[62] local Temp=68
Chain[5] Chip[62] middle Temp=89
Chain[6] Chip[62] TempTypeID=55 middle offset=-4
Chain[6] Chip[62] local Temp=66
Chain[6] Chip[62] middle Temp=86
Chain[7] Chip[62] TempTypeID=55 middle offset=-3
Chain[7] Chip[62] local Temp=66
Chain[7] Chip[62] middle Temp=85
set FAN speed according to: temp_highest=89 temp_top1[PWM_T]=89 temp_top1[TEMP_POS_LOCAL]=68 temp_change=1 fix_fan_steps=3
FAN PWM: 82

okay there are multiple fails.

you may have the everything looks good fail all boards have a light but 1 boards does not work fail.

if you were on old software you would show say 3 x 4000 = 12000 power would be say 1200 watts but the pools would give you say 2x 4000 = 8000 hash. then in a week or so the board will fully die the little lite on it will vanish and you have the more classic fail.

with auto tune you get 0 hash but pull full watts with the 1 dead but shows good board.

so pull two cables mine with board A for 4 hours and report back
then pull the cable on A add the cable to B mine for four hours report back.

then pull the cable on b add the cable to C mine for four hours report back.

with luck 2 of your boards will hash. if so then put the cables on both of them and see if you go to 8000 or so.,

when all is said and done you should or could have 2 working boards.

mail the dead one back in.