Quote from: jonny51 on July 13, 2017, 02:40:32 PM

Quote from: Ireul on July 13, 2017, 10:03:13 AM

Quote from: toomeke on July 12, 2017, 12:41:01 PM

Quote from: Ireul on July 12, 2017, 10:40:37 AM

I have a Sapphire Radeon RX 470 MINING Edition 8192MB GDDR5 Samsung PCI-Express Graphics Card, and I am the following settings for simplemining

Code:

-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal obfuscated.test1/obfuscated@gmail.com -dpsw x

on claymore-eth-v9.7
It is reporting the following speeds 15.37 MH/s 461.22 MH/s
Does this seem a reasonable speed for this single card? I have never dual mined nor used this card before so I am unsure on what type of hash speeds I should be getting.

Thanks.

Use the flag below(Taken from the claymore 9.xxx readme txt file), this balances out how much hashing power you want between your main and secondary coins

-dcri   Decred/Siacoin/Lbry/Pascal intensity, or Ethereum fine-tuning value in ETH-only ASM mode. Default value is 30, you can adjust this value to get the best Decred/Siacoin/Lbry mining speed without reducing Ethereum mining speed.
   You can also specify values for every card, for example "-dcri 30,100,50".
   You can change the intensity in runtime with "+" and "-" keys and check current statistics with "s" key.
   For example, by default (-dcri 30) 390 card shows 29MH/s for Ethereum and 440MH/s for Decred. Setting -dcri 70 causes 24MH/s for Ethereum and 850MH/s for Decred.

for me I find -dcri 40 seems a good balance, but tweak and tune to taste

Hi toomeke, thanks for the reply, could you give me some further help with your comment, I have tried setting "-dcri 30", -dcri 50" and -dcri 100" non of which make a difference below is an example of the change I made

Code:

-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal obfuscated.test1/obfuscated@gmail.com -dpsw x
To
-epool eth-eu1.nanopool.org:9999 -ewal obfuscated.test1/obfuscated@gmail.com -dcri 30 x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dcri 30 obfuscated.test1/obfuscated@gmail.com -dpsw x

Which does not seem to change anything.

for my RX Cards i use usually around 9 and with the GTX no rig more then 15!

Best to test it is running Claymore in windows. Then you press the - key until it says decr 1. There must be absolutely no effect on ETH mining speeds, otherwise you have some other issue. And from that on you can go with the + key one up, press S for statistics and look if your ETH speed is lowered, if not press + to go up with decr and again S to see how the mining speeds are. Best way to get the best Decr settings for your rig. Normally these cards are runnig around 27mhs eth and 250mhs pasc/sia. Just try 9 and look how your balance is Tongue

Hi, 10 seems to be the sweet spot as there is very little change going down to 9.
Do you have experience with overclocking too?