Quote from: deathless on November 27, 2017, 06:43:53 PM

Quote from: BartoszN1990 on November 27, 2017, 06:41:34 PM

Quote from: blissz on November 27, 2017, 06:38:09 PM

Quote from: BartoszN1990 on November 27, 2017, 06:27:42 PM

i use oryginal bitmain fw now.

when i set 400 M system dont se chain 1
when i set 350 m system se chain 54 chips but not mining

Quote

AntMiner
Chain#   ASIC#   Frequency   GH/S(RT)   HW   Temp(PCB)   Temp(Chip)   ASIC status
1   54   350   0.00   0   0   0   xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxx
2   60   350   4434.28   0   23   33   oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
3   60   350   4281.28   0   22   31   oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo

This is then a hardware problem. I am afraid you have to RMA the first board. My advice to keep mining on the two other boards (the latest custom firmware can run with 2 chains connected)

There is no reason to send it back to china is expensive to send and collect + time ti waitng.. So what one chain go rubish ? or there is posible to fix it ? .. i change place chain and show the same

Quote

Nov 27 18:38:22 (none) local0.notice cgminer[375]: set_frequency: frequency = 350
Nov 27 18:38:22 (none) local0.notice cgminer[375]: software_set_address_chain: chain 0 has 60 ASIC, and addrInterval is 1
Nov 27 18:38:22 (none) local0.notice cgminer[375]: Now Set

Chain Address

Nov 27 18:38:23 (none) local0.notice cgminer[375]: software_set_address_chain: chain 1 has 54 ASIC, and addrInterval is 1
Nov 27 18:38:23 (none) local0.notice cgminer[375]: Now Set [1] Chain Address
Nov 27 18:38:23 (none) local0.notice cgminer[375]: software_set_address_chain: chain 2 has 60 ASIC, and addrInterval is 1

So i thing yes chain is broken .... Where i can diagniostick one chain or fix ?

Have you tried to unplug the other 2 chains and see if the one that isnt working boot in?

I unplug 2 chain and left only one. system dosnt start ...

Quote

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65280
[ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 64768 pages, LIFO batch:15
[ 0.000000] AM335X ES1.0 (neon )
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 255MB = 255MB total
[ 0.000000] Memory: 238676k/238676k available, 23468k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB)
[ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB)
[ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB)
[ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000355] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[ 0.015435] pid_max: default: 32768 minimum: 301
[ 0.015666] Security Framework initialized
[ 0.015761] Mount-cache hash table entries: 512
[ 0.024599] Initializing cgroup subsys cpuacct
[ 0.024631] Initializing cgroup subsys memory
[ 0.024693] Initializing cgroup subsys blkio
[ 0.024831] CPU: Testing write buffer coherency: ok
[ 0.025406] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.025482] Setting up static identity map for 0x8038c820 - 0x8038c86c
[ 0.026807] Brought up 1 CPUs
[ 0.026829] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[ 0.028124] devtmpfs: initialized
[ 0.092510] pinctrl core: initialized pinctrl subsystem
[ 0.092725] rstctl core: initialized rstctl subsystem
[ 0.093218] regulator-dummy: no parameters
[ 0.093786] NET: Registered protocol family 16
[ 0.094486] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.104152] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[ 0.104336] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[ 0.105420] platform 49000000.edma: alias fck already exists
[ 0.105454] platform 49000000.edma: alias fck already exists
[ 0.105482] platform 49000000.edma: alias fck already exists
[ 0.106628] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[ 0.106809] OMAP GPIO hardware version 0.1
[ 0.108209] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[ 0.109525] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[ 0.110843] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[ 0.111473] of_get_named_gpio_flags exited with status 52
[ 0.111503] gpio-rctrl rstctl.3: loaded OK
[ 0.116609] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 0.119820] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.122011] cpsw.0: No hwaddr in dt. Using 90:70:65:30:e0:f3 from efuse
[ 0.122042] cpsw.1: No hwaddr in dt. Using 90:70:65:30:e0:f5 from efuse
[ 0.137599] bio: create slab at 0
[ 0.149725] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[ 0.149967] of_get_named_gpio_flags: can't parse gpios property
[ 0.150254] vmmcsd_fixed: 3300 mV
[ 0.153365] SCSI subsystem initialized
[ 0.153814] usbcore: registered new interface driver usbfs
[ 0.153928] usbcore: registered new interface driver hub
[ 0.154270] usbcore: registered new device driver usb
[ 0.156378] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[ 0.156412] omap_i2c 4819c000.i2c: unable to select pin group
[ 0.156608] media: Linux media interface: v0.10
[ 0.156702] Linux video capture interface: v2.00
[ 0.156819] pps_core: LinuxPPS API ver. 1 registered
[ 0.156835] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.157556] Advanced Linux Sound Architecture Driver Initialized.
[ 0.158744] Switching to clocksource gp_timer
[ 0.176777] NET: Registered protocol family 2
[ 0.177769] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.177858] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[ 0.177947] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.178040] TCP: reno registered
[ 0.178067] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.178113] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.178609] NET: Registered protocol family 1
[ 0.179198] RPC: Registered named UNIX socket transport module.
[ 0.179218] RPC: Registered udp transport module.
[ 0.179232] RPC: Registered tcp transport module.
[ 0.179245] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.179634] Trying to unpack rootfs image as initramfs...
[ 1.941896] Freeing initrd memory: 12240K
[ 1.942633] CPU PMU: probing PMU on CPU 0
[ 1.942669] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 1.943215] omap2_mbox_probe: platform not supported
[ 1.947131] VFS: Disk quotas dquot_6.5.2
[ 1.947368] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.948765] NFS: Registering the id_resolver key type
[ 1.948858] Key type id_resolver registered
[ 1.948874] Key type id_legacy registered
[ 1.948941] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.949377] msgmni has been set to 490
[ 1.952273] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.952300] io scheduler noop registered
[ 1.952316] io scheduler deadline registered
[ 1.952373] io scheduler cfq registered (default)
[ 1.956442] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.958870] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[ 1.959154] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[ 2.619944] console [ttyO0] enabled
[ 2.624517] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[ 2.633187] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[ 2.641870] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[ 2.650476] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[ 2.659498] [drm] Initialized drm 1.1.0 20060810
[ 2.678176] brd: module loaded
[ 2.688462] loop: module loaded
[ 2.692691] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[ 2.702624] nand_get_flash_type: 2c,da against 2c,da
[ 2.708149] ONFI param page 0 valid
[ 2.711822] ONFI flash detected
[ 2.715139] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[ 2.727051] omap2-nand: detected x8 NAND flash
[ 2.731716] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[ 2.737298] omap2-nand: using custom ecc layout
[ 2.742140] 10 ofpart partitions found on MTD device omap2-nand.0
[ 2.748535] Creating 10 MTD partitions on "omap2-nand.0":
[ 2.754213] 0x000000000000-0x000000020000 : "spl"
[ 2.761022] 0x000000020000-0x000000040000 : "spl_backup1"
[ 2.768482] 0x000000040000-0x000000060000 : "spl_backup2"
[ 2.775850] 0x000000060000-0x000000080000 : "spl_backup3"
[ 2.783264] 0x000000080000-0x000000240000 : "u-boot"
[ 2.791475] 0x000000240000-0x000000260000 : "bootenv"
[ 2.798439] 0x000000260000-0x000000280000 : "fdt"
[ 2.805026] 0x000000280000-0x000000780000 : "kernel"
[ 2.816058] 0x000000800000-0x000001c00000 : "root"
[ 2.839552] 0x000001c00000-0x000003000000 : "config"
[ 2.863332] OneNAND driver initializing
[ 2.869073] usbcore: registered new interface driver asix
[ 2.874889] usbcore: registered new interface driver cdc_ether
[ 2.881133] usbcore: registered new interface driver smsc95xx
[ 2.887257] usbcore: registered new interface driver net1080
[ 2.893297] usbcore: registered new interface driver cdc_subset
[ 2.899592] usbcore: registered new interface driver zaurus
[ 2.905598] usbcore: registered new interface driver cdc_ncm
[ 2.912342] usbcore: registered new interface driver cdc_acm
[ 2.918303] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.926683] Initializing USB Mass Storage driver...
[ 2.931922] usbcore: registered new interface driver usb-storage
[ 2.938221] USB Mass Storage support registered.
[ 2.943267] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 2.950021] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[ 2.955258] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[ 2.964028] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 2.964050] musb-hdrc: MHDRC RTL version 2.0
[ 2.964065] musb-hdrc: setup fifo_mode 4
[ 2.964093] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 2.964237] musb-hdrc musb-hdrc.0.auto: *** mode=3
[ 2.969280] musb-hdrc musb-hdrc.0.auto: *** power=250
[ 2.975339] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[ 2.980577] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[ 2.989346] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 2.989366] musb-hdrc: MHDRC RTL version 2.0
[ 2.989380] musb-hdrc: setup fifo_mode 4
[ 2.989402] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 2.989539] musb-hdrc musb-hdrc.1.auto: *** mode=1
[ 2.994583] musb-hdrc musb-hdrc.1.auto: *** power=250
[ 2.999892] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 3.006570] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[ 3.014815] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[ 3.014920] usb usb1: default language 0x0409
[ 3.014978] usb usb1: udev 1, busnum 1, minor = 0
[ 3.015002] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.022130] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.029703] usb usb1: Product: MUSB HDRC host driver
[ 3.034918] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[ 3.040586] usb usb1: SerialNumber: musb-hdrc.1.auto
[ 3.046565] usb usb1: usb_probe_device
[ 3.046591] usb usb1: configuration #1 chosen from 1 choice
[ 3.046656] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 3.046857] hub 1-0:1.0: usb_probe_interface
[ 3.046879] hub 1-0:1.0: usb_probe_interface - got id
[ 3.046907] hub 1-0:1.0: USB hub found
[ 3.050908] hub 1-0:1.0: 1 port detected
[ 3.055046] hub 1-0:1.0: standalone hub
[ 3.055066] hub 1-0:1.0: individual port power switching
[ 3.055084] hub 1-0:1.0: no over-current protection
[ 3.055102] hub 1-0:1.0: Single TT
[ 3.055123] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 3.055143] hub 1-0:1.0: power on to power good time: 10ms
[ 3.055197] hub 1-0:1.0: local power source is good
[ 3.055348] hub 1-0:1.0: enabling power on all ports
[ 3.056409] mousedev: PS/2 mouse device common for all mice
[ 3.064355] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[ 3.072126] i2c /dev entries driver
[ 3.077179] pps_ldisc: PPS line discipline registered
[ 3.082677] Driver for 1-wire Dallas network protocol.
[ 3.089965] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 3.097537] cpuidle: using governor ladder
[ 3.101862] cpuidle: using governor menu
[ 3.106455] of_get_named_gpio_flags exited with status 6
[ 3.106477] of_get_named_gpio_flags: can't parse gpios property
[ 3.106493] of_get_named_gpio_flags: can't parse gpios property
[ 3.106530] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[ 3.113768] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[ 3.120583] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[ 3.127806] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[ 3.135132] mmc.4 supply vmmc_aux not found, using dummy regulator
[ 3.142088] omap_hsmmc mmc.4: pins are not configured from the driver
[ 3.156997] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 3.177023] of_get_named_gpio_flags exited with status -517
[ 3.177091] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 3.184867] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.191648] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[ 3.198842] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 3.206951] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 3.213297] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[ 3.220480] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[ 3.232734] usbcore: registered new interface driver usbhid
[ 3.238650] usbhid: USB HID core driver
[ 3.245542] TCP: cubic registered
[ 3.249065] Initializing XFRM netlink socket
[ 3.253631] NET: Registered protocol family 17
[ 3.258514] NET: Registered protocol family 15
[ 3.263384] Key type dns_resolver registered
[ 3.268019] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 3.276100] ThumbEE CPU extension supported.
[ 3.280610] Registering SWP/SWPB emulation handler
[ 3.286625] registered taskstats version 1
[ 3.293251] of_get_named_gpio_flags exited with status -517
[ 3.293322] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 3.350305] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 3.356717] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[ 3.371263] libphy: 4a101000.mdio: probed
[ 3.375578] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[ 3.385812] Detected MACID = 90:70:65:30:e0:f3
[ 3.390493] cpsw 4a100000.ethernet: NAPI disabled
[ 3.395882] of_get_named_gpio_flags exited with status -517
[ 3.395949] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 3.404680] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 3.413959] cpu0 supply cpu0 not found, using dummy regulator
[ 3.420443] cpufreq_cpu0: failed to scale voltage up: -22
[ 3.426261] cpufreq_cpu0: failed to scale voltage up: -22
[ 3.439030] ALSA device list:
[ 3.442260] No soundcards found.
[ 3.446819] Freeing init memory: 264K
[ 3.450869] Failed to execute /init
[ 4.448717] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 5.772478] net eth0: initializing cpsw version 1.12 (0)
[ 5.781403] net eth0: phy found : id is : 0x7c0f1
[ 5.786840] libphy: PHY 4a101000.mdio:01 not found
[ 5.792036] net eth0: phy 4a101000.mdio:01 not found on slave 1
[ 8.856687] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Nov 27 19:05:23 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Nov 27 19:05:23 (none) local0.warn cgminer: Started cgminer 4.9.0
Nov 27 19:05:23 (none) local0.warn cgminer[375]: bitmain_DASH_init
Nov 27 19:05:23 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:23 (none) local0.err cgminer[375]: FAN2 too slow ...
Nov 27 19:05:24 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:24 (none) local0.err cgminer[375]: FAN2 too slow ...
Nov 27 19:05:24 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:24 (none) local0.err cgminer[375]: FAN2 too slow ...
Nov 27 19:05:25 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:25 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:26 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:26 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:27 (none) local0.err cgminer[375]: FAN1 too slow ...
Nov 27 19:05:27 (none) local0.warn cgminer[375]: check_fan_speed OK
Nov 27 19:05:27 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio47/value chain 2
Nov 27 19:05:27 (none) local0.notice cgminer[375]: detect total chain num 1
Nov 27 19:05:27 (none) local0.notice cgminer[375]: i2c init ok
Nov 27 19:05:27 (none) local0.notice cgminer[375]: check_whether_need_update_pic_program
Nov 27 19:05:28 (none) local0.notice cgminer[375]: reset_PIC16F1704_pic_new ok
Nov 27 19:05:29 (none) local0.notice cgminer[375]: jump_from_loader_to_app_PIC16F1704_new ok
Nov 27 19:05:29 (none) local0.notice cgminer[375]: get_PIC16F1704_software_version_new ok, version = 0x81
Nov 27 19:05:29 (none) local0.notice cgminer[375]: every_chain_reset_PIC16F1704_pic_new
Nov 27 19:05:31 (none) local0.notice cgminer[375]: reset_PIC16F1704_pic_new ok
Nov 27 19:05:31 (none) local0.notice cgminer[375]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Nov 27 19:05:32 (none) local0.notice cgminer[375]: jump_from_loader_to_app_PIC16F1704_new ok
Nov 27 19:05:32 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Nov 27 19:05:32 (none) local0.notice cgminer[375]: pic_heart_beat_func_new
Nov 27 19:05:33 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Nov 27 19:05:33 (none) local0.notice cgminer[375]: reset_all_hash_board
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init_chain
Nov 27 19:05:34 (none) local0.notice cgminer[375]: open device over
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init_chain
Nov 27 19:05:34 (none) local0.notice cgminer[375]: open device over
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init_chain
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init_chain chainid = 2
Nov 27 19:05:34 (none) local0.err cgminer[375]: create rx read thread for chain 2 ok
Nov 27 19:05:34 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[2]
Nov 27 19:05:34 (none) local0.err cgminer[375]: create tx read thread for chain 2 ok
Nov 27 19:05:34 (none) local0.notice cgminer[375]: open device over
Nov 27 19:05:34 (none) local0.notice cgminer[375]: tty_init_chain
Nov 27 19:05:34 (none) local0.notice cgminer[375]: open device over
Nov 27 19:05:35 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Nov 27 19:05:35 (none) local0.warn cgminer[375]: check_asic_reg: Chain2 has 0 ASICs
Nov 27 19:05:35 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Nov 27 19:05:37 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Nov 27 19:05:37 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Nov 27 19:05:38 (none) local0.notice cgminer[375]: reset_all_hash_board
Nov 27 19:05:39 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Nov 27 19:05:39 (none) local0.warn cgminer[375]: check_asic_reg: Chain2 has 54 ASICs
Nov 27 19:05:39 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Nov 27 19:05:39 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Nov 27 19:05:41 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Nov 27 19:05:41 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Nov 27 19:05:42 (none) local0.notice cgminer[375]: reset_all_hash_board
Nov 27 19:05:42 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Nov 27 19:05:43 (none) local0.warn cgminer[375]: check_asic_reg: Chain2 has 54 ASICs
Nov 27 19:05:43 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Nov 27 19:05:43 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Nov 27 19:05:45 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Nov 27 19:05:45 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Nov 27 19:05:45 (none) local0.notice cgminer[375]: reset_all_hash_board
Nov 27 19:05:46 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Nov 27 19:05:47 (none) local0.warn cgminer[375]: check_asic_reg: Chain2 has 54 ASICs
Nov 27 19:05:47 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Nov 27 19:05:47 (none) local0.notice cgminer[375]: calculate_address_interval: temp_asic_number = 64, addrInterval = 1
Nov 27 19:05:47 (none) local0.notice cgminer[375]: calculate_address_interval: CHIP_OFFSET = 0x04000000, CORE_OFFSET = 0x00800000
Nov 27 19:05:47 (none) local0.notice cgminer[375]: set_ticket_mask ticket_mask = 0x0000001b
Nov 27 19:05:47 (none) local0.notice cgminer[375]: every_chain_get_PIC16F1704_freq_new
Nov 27 19:05:48 (none) local0.notice cgminer[375]: set_frequency: frequency = 537
Nov 27 19:05:48 (none) local0.notice cgminer[375]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 1
Nov 27 19:05:48 (none) local0.notice cgminer[375]: software_set_address_chain: chain 1 has 0 ASIC, and addrInterval is 1
Nov 27 19:05:48 (none) local0.notice cgminer[375]: software_set_address_chain: chain 2 has 54 ASIC, and addrInterval is 1
Nov 27 19:05:48 (none) local0.notice cgminer[375]: Now Set [2] Chain Address
Nov 27 19:05:49 (none) local0.notice cgminer[375]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 1
Nov 27 19:05:49 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Nov 27 19:05:49 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Nov 27 19:05:49 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Nov 27 19:05:49 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Nov 27 19:05:49 (none) local0.notice cgminer[375]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Nov 27 19:05:49 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Nov 27 19:05:49 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Nov 27 19:05:49 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Nov 27 19:05:49 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Nov 27 19:05:49 (none) local0.notice cgminer[375]: 2 calibration_sensor_offset_chain
Nov 27 19:05:50 (none) local0.notice cgminer[375]: chain:2 local:0 remote:0
Nov 27 19:05:50 (none) local0.warn cgminer[375]: Chain 2 set_temperature_offset_value_chain_sensor
Nov 27 19:05:51 (none) local0.notice cgminer[375]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00,
Nov 27 19:05:51 (none) local0.warn cgminer[375]: Chain 2 set_temperature_offset_value_chain
Nov 27 19:05:51 (none) local0.warn cgminer[375]: Chain 2 set_temperature_offset_value_chain_sensor
Nov 27 19:05:51 (none) local0.notice cgminer[375]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00,
Nov 27 19:05:51 (none) local0.notice cgminer[375]: frequency = '537'
Nov 27 19:05:51 (none) local0.notice cgminer[375]: dev.timeout = 562356 us
Nov 27 19:05:51 (none) local0.notice cgminer[375]: open_core_chain
Nov 27 19:05:51 (none) local0.notice cgminer[375]: open_core_chain
Nov 27 19:05:51 (none) local0.notice cgminer[375]: open_core_chain
Nov 27 19:05:51 (none) local0.notice cgminer[375]: open_core_chain
Nov 27 19:05:54 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:05:54 (none) local0.err cgminer[375]: cgminer time error total_secs = 1511809554.976425 last_total_secs = 1.000000
Nov 27 19:05:56 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:05:59 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:00 (none) local0.warn cgminer[375]: API running in IP access mode on port 4028 (14)
Nov 27 19:06:02 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:05 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:07 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:10 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:13 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:15 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:18 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:21 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:24 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:26 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:29 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:32 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:34 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:37 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:40 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:43 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:45 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:48 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:51 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:53 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:56 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:06:59 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:07:02 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:07:04 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:07:07 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Nov 27 19:07:10 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!

Quote

3 54 537 0.00 0 0 0 xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxx