Quote from: Sandal_Hat on December 20, 2017, 12:42:45 PM

Quote from: cableiso on December 11, 2017, 01:13:08 PM

@MikeyKing, read the last line of your log - the device is only finding one fan.

Power down, try unplugging and replugging both fans. If that doesn't work get in touch with bitmain, might be a bad fan or controller board.

Code:

Checking fans!get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[2] speed=5880
get fan[5] speed=6120
get fan[2] speed=5880
get fan[5] speed=6120
get fan[2] speed=5880
get fan[5] speed=6120
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=125 value=870
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=890 [91]
Chain[J8] get working chain_voltage_pic=91
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
[u][b]Chain[J8] has 0 asic[/b][/u]
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
Chain[J6] has core num in PIC
Chain[J7] has core num in PIC
miner total rate=9329GH/s fixed rate=9000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=662

Can see wats wrong with mine? Only 2 hashboards working...
I think I found the problem..it just doesnt detect after awhile... It was fine before zzzz

Chain 8 was working fine before.

(Moderator note: This post was edited by frodocooper to use code tags, instead of quote tags, for the log output.)

Update, this was fixed by changing my ethernet cable to a better one. I am not kidding. It fixed it.
I changed from a right angled one to a better one