Hey,
Sorry if this has been covered previously, but has any one had an issue getting the firmware to load?
I tried multiple times today from various browsers.
I tried both the Antminer-D3-20171210_0-blissz.tar.gz & Antminer-D3-v2.04-20171222_0_beta-blissz.tar.gz
It starts the upload, does a reboot, goes offline, comes back up, but it is always the stock firmware.
I have the latest batch of D3, the 19.whatever. I have it turned down to 419 on the frequency, and the fan down for the noise. I'm fine with the 15GH/s, but would like to be able to adjust voltages.
Any advice would be appreciated, if anyone has had this issue before.
Thanks,
@bigrobatx
My apologies to Zerp86 for using his post/
thank in advance to blissz to help D3 community for this firmware..
will trying 1 D3 first.. to find the right setting for my D3.. and willl setting all my D3 if good to to with this firmware
Sorry if this has been covered previously, but has any one had an issue getting the firmware to load?
I tried multiple times today from various browsers.
I tried both the Antminer-D3-20171210_0-blissz.tar.gz & Antminer-D3-v2.04-20171222_0_beta-blissz.tar.gz
It starts the upload, does a reboot, goes offline, comes back up, but it is always the stock firmware.
I have the latest batch of D3, the 19.whatever. I have it turned down to 419 on the frequency, and the fan down for the noise. I'm fine with the 15GH/s, but would like to be able to adjust voltages.
Any advice would be appreciated, if anyone has had this issue before.
Thanks,
@bigrobatx
My apologies to Zerp86 for using his post/
WARNING THIS FIRMWARE MIGHT VOID THE WARRANTY ON YOUR MINER
https://img4.hostingpics.net/pics/145857banner.jpg
https://img15.hostingpics.net/pics/893377382.jpg
https://img15.hostingpics.net/pics/550407481.jpg
v1.12 :: 10/12 :: RECOMMENDED UPDATE
Download:
https://mega.nz/#!ylJX0LCQ!8JWryI0jDhgMvPdH2mrOvybkXCtrpYtQpxu0akdxU1s
Upgrade instructions:
Changes 10/12:
- Improved awesome miner / other mining managers compatibility (setting the priority was not working)
- fix kernel log window height (saves you double scrolling...)
- added permanent antbleed fix (prevent remote control of your miner by bitmain
) -> for details see http://www.antbleed.com/
https://img4.hostingpics.net/pics/145857banner.jpg
https://img15.hostingpics.net/pics/893377382.jpg
https://img15.hostingpics.net/pics/550407481.jpg
v1.12 :: 10/12 :: RECOMMENDED UPDATE
Download:
https://mega.nz/#!ylJX0LCQ!8JWryI0jDhgMvPdH2mrOvybkXCtrpYtQpxu0akdxU1s
Upgrade instructions:
- Recommended, at your current firmware, set the miner frequency at 400mhz and set your fan speed manual at 25% before flashing.
- Download the custom firmware. (don't unpack it)
- Flash by going to "System" -> "Upgrade" -> "Flash new firmware image" and select the custom firmware.
- After flashing, check the advanced settings page and start at the lowest voltage setting and 400mhz. From there increase your frequency to see how high you can go at the lowest voltage setting.
- Start tweaking some more. See the profile suggestions below.
Changes 10/12:
- Improved awesome miner / other mining managers compatibility (setting the priority was not working)
- fix kernel log window height (saves you double scrolling...)
- added permanent antbleed fix (prevent remote control of your miner by bitmain
) -> for details see http://www.antbleed.com/thank in advance to blissz to help D3 community for this firmware..
will trying 1 D3 first.. to find the right setting for my D3.. and willl setting all my D3 if good to to with this firmware