Quote from: minerbobbert on March 10, 2018, 07:20:23 PM

New update if this tells anyone anything - I am still getting the failures with constant resets. Last night I had these running for 12 hours or so and it had cycled through nearly 180 of these errors:

...
[2018-03-10 07:59:21.318] Accepted 02102f35 Diff 124/48 GSE 179
[2018-03-10 07:59:24.474] Accepted 04410e18 Diff 60/48 GSE 179
[2018-03-10 07:59:25.540] Accepted 7f923adf Diff 514/48 GSE 179
[2018-03-10 07:59:26.017] GSE 179 failure, disabling!
[2018-03-10 07:59:26.017] GSE 179: setting frequency to 100.00MHz
[2018-03-10 07:59:29.626] GSE 180: Terminus BM1384 Bitcoin Miner (10030015)
[2018-03-10 07:59:29.836] Hotplug: GekkoScience added GSE 180
[2018-03-10 07:59:29.942] GSE 180: found 8 chip(s)
[2018-03-10 07:59:30.058] GSE 180: setting frequency to 100.00MHz
[2018-03-10 07:59:30.072] GSE 180: open cores @ 100.00MHz
[2018-03-10 07:59:31.751] GSE 180: start work @ 100.00MHz
[2018-03-10 07:59:46.753] GSE 180: setting frequency to 125.00MHz
[2018-03-10 07:59:48.045] Accepted 01074342 Diff 249/48 GSE 180

Then a new one popped up:

[2018-03-10 08:02:58.292] Accepted 89f1fd11 Diff 475/48 GSE 180
[2018-03-10 08:02:59.924] GSE 180 SendWork usb write err:(-7) LIBUSB_ERROR_TIMEOUT
[2018-03-10 08:03:32.547] GSE 180 attempted reset got err:(-5) LIBUSB_ERROR_NOT_FOUND
[2018-03-10 08:03:32.548] GSE 180: usb failure (-5)
[2018-03-10 08:03:32.549] GSE 180 failure, disabling!
[2018-03-10 08:03:32.549] GSE 180: setting frequency to 100.00MHz
[2018-03-10 08:03:35.057] GekkoScience detect (1:7) failed to initialise (incorrect device?), resetting
[2018-03-10 08:03:35.057] failed usb_init
[2018-03-10 08:03:40.493] GekkoScience detect (1:7) failed to initialise (incorrect device?), resetting
[2018-03-10 08:03:40.494] failed usb_init
[2018-03-10 08:03:45.877] GekkoScience detect (1:7) failed to initialise (incorrect device?), resetting
[2018-03-10 08:03:45.878] failed usb_init
[2018-03-10 08:03:51.267] GekkoScience detect (1:7) failed to initialise (incorrect device?), resetting
[2018-03-10 08:03:51.267] failed usb_init
[2018-03-10 08:03:56.601] GekkoScience detect (1:5) failed to initialise (incorrect device?), resetting
[2018-03-10 08:03:56.601] failed usb_init
[2018-03-10 08:03:56.652] GekkoScience detect (1:7) failed to initialise

And so on for hours on end. I found it when I woke up today and restarted everything, but one of my miners is getting that failure error every few minutes or so. It successfully starts again at 100mHz and eventually goes up (I have them set to max 150 right now to make sure overwork isn't the cause of this) until it resets again. Cycling through this process means my overall hash rate is about 10-15 less than it should be when averaged out... plus the unsettling feeling that one of these is on the verge of breaking...

It looks like they are not getting enough power and so the setting back to 100Mhz gets it going again. Have you adjusted the blue pot on the terminus or left it stock? Once it is running do you get Hardware Errors? If so the chips are not getting enough voltage and each Terminus seems to be a slightly different voltage at stock so trying turning up the blue voltage adjustment but only a little (1/8 of a turn) until the HW errors stop.