Quote from: EnzoMatrix on July 30, 2011, 05:12:19 AM

You may want to verify that phoenix.py is executable

Code:

sudo chmod +x /opt/miners/phoenix/phoenix.py

Did that, now it seems to startup, if I run the startminers.sh script manually, but all I get is:

Code:

ATI Overdrive(TM) enabled
INF: Nr. of Adapters: 6
INF: Nr. of Adapters: 6
INF: Adapter index: 0, active, ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 0, active, ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 1, inact., ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 1, inact., ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 2, inact., ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 2, inact., ID:34858784, ATI Radeon HD 5800 Series
INF: Adapter index: 3, active, ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index: 3, active, ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index: 4, inact., ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index: 4, inact., ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index: 5, inact., ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index: 5, inact., ID:35472080, ATI Radeon HD 5800 Series
INF: Adapter index 3 choosen.
INF: Adapter index 0 choosen.
INF: Nr. of Performance Levels: 3
INF: Card's default Perf Level 0: GPU 157MHz Memory 300MHz Voltage 0.968V
INF: Nr. of Performance Levels: 3
INF: Card's default Perf Level 0: GPU 157MHz Memory 300MHz Voltage 0.968V
INF: Card's default Perf Level 1: GPU 550MHz Memory 900MHz Voltage 1.068V
INF: Card's default Perf Level 2: GPU 725MHz Memory 1000MHz Voltage 1.118V
INF: Card's default Perf Level 1: GPU 550MHz Memory 900MHz Voltage 1.068V
INF: Card's default Perf Level 2: GPU 725MHz Memory 1000MHz Voltage 1.118V
ACT: Set fan speed to default
ACT: Set fan speed to default
INF: Nr. of Displays to check 4
INF: Color temp disp(2) :
INF: current 6500K default 6500K
INF: min 4000K max 10000K step 100K
WRN: color temperature setting not supported.
INF: Nr. of Displays to check 4
WRN: color temperature setting not supported.
ACT: Set fan speed to default
INF: FanCtrl mode off
ACT: SetOverdriveValues: Level 0: 157MHz, 300MHz, MHz, 0.968V
ACT: SetOverdriveValues: Level 1: 550MHz, 425MHz, MHz, 1.068V
ACT: SetOverdriveValues: Level 2: 875MHz, 425MHz, MHz, 1.118V
INF: Default profile found and loaded.
root@linuxcoin:/usr/local/bin# ACT: Set fan speed to default
INF: FanCtrl mode off
ACT: SetOverdriveValues: Level 0: 157MHz, 300MHz, MHz, 0.968V
ACT: SetOverdriveValues: Level 1: 550MHz, 425MHz, MHz, 1.068V
ACT: SetOverdriveValues: Level 2: 875MHz, 425MHz, MHz, 1.118V
INF: Default profile found and loaded.
[30/07/2011 05:32:23] Phoenix r101 starting...
[0 Khash/sec] [0 Accepted] [0 Rejected][30/07/2011 05:32:23] Phoenix r101 starting...
[30/07/2011 05:32:53] Failed to connect, retrying...
[0 Kha[30/07/2011 05:32:53] Failed to connect, retrying...
[30/07/2011 05:33:38] Failed to connect, retrying...
[30/07/2011 05:33:38] Failed to connect, retrying...
[30/07/2011 05:34:23] Failed to connect, retrying...
[30/07/2011 05:34:23] Failed to connect, retrying...
[30/07/2011 05:35:08] Failed to connect, retrying...
[30/07/2011 05:35:08] Failed to connect, retrying...
[30/07/2011 05:35:53] Failed to connect, retrying...
[30/07/2011 05:35:53] Failed to connect, retrying...
[0 Khash/sec] [0 Accepted] [0 Rejected] [RPC

And, it won't run at all with the auto.sh script, same as before, starts up the terminal and the two instances of AMDOverdriveCtrl, then shuts everything down.

*Edit*

Hmm, seems if I type this in the phoenix directory, it starts up just fine:

Code:

./phoenix.py -u http://USERNAME.WORKERNAME:PASSWORD@mining.bitcoin.cz:8332/ -k poclbm DEVICE=0 VECTORS AGGRESSION=3

so Phoenix works, just not via the scripts. Guess I try and figure out where they are going wrong