Quote from: laik2 on March 13, 2019, 09:54:36 AM

Yes, you are right, ethash is supported for Hawaii, I was trying ubiq which wasn't working!
I can confirm that everything is working with my experimental 3gen AMD rig.
http://prntscr.com/mx7vkm

Ubqhash should also work on Hawaii on Linux and amdgpu-pro drivers. If it doesn't, please send us a log file to investigate the problem.

Quote from: nordmann666 on March 15, 2019, 09:04:03 AM

after i shut down my nvidia rigs some month ago i tried yesterday again cause i wanna know what i can reach today with my P106-100 with Samsung mem

newest Win10 x64 - newest drivers from nvidia installed in device manager
Afterburner to +100 Core, +500 Mem, PL 70

start Phoenix

24MHs ok
but after one minute 0MHs on all cards hmmm?!?!

Eth speed: 192.987 MH/s, shares: 1/0/0, time: 0:01
GPUs: 1: 24.086 MH/s (0) 2: 24.137 MH/s (0) 3: 24.132 MH/s (0) 4: 24.129 MH/s (0) 5: 24.129 MH/s (1) 6: 24.133 MH/s (0) 7: 24.145 MH/s (0) 8: 24.097 MH/s (0)
Eth: New job #0d0675c7 from eu1.ethpool.org:3333; diff: 4000MH
Eth speed: 192.944 MH/s, shares: 1/0/0, time: 0:01
GPUs: 1: 24.067 MH/s (0) 2: 24.134 MH/s (0) 3: 24.132 MH/s (0) 4: 24.129 MH/s (0) 5: 24.131 MH/s (1) 6: 24.135 MH/s (0) 7: 24.145 MH/s (0) 8: 24.071 MH/s (0)
Eth: New job #6fa91163 from eu1.ethpool.org:3333; diff: 4000MH
Eth speed: 192.972 MH/s, shares: 1/0/0, time: 0:01
GPUs: 1: 24.095 MH/s (0) 2: 24.132 MH/s (0) 3: 24.125 MH/s (0) 4: 24.120 MH/s (0) 5: 24.126 MH/s (1) 6: 24.136 MH/s (0) 7: 24.133 MH/s (0) 8: 24.106 MH/s (0)
Eth: New job #83e63d11 from eu1.ethpool.org:3333; diff: 4000MH
Eth: New job #605a62eb from eu1.ethpool.org:3333; diff: 4000MH
Eth: New job #18387554 from eu1.ethpool.org:3333; diff: 4000MH
Eth speed: 72.330 MH/s, shares: 1/0/0, time: 0:01
GPUs: 1: 24.095 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 24.127 MH/s (1) 6: 0.000 MH/s (0) 7: 0.000 MH/s (0) 8: 24.108 MH/s (0)
Eth: New job #3f4debaa from eu1.ethpool.org:3333; diff: 4000MH
Eth speed: 0.000 MH/s, shares: 1/0/0, time: 0:01
GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (1) 6: 0.000 MH/s (0) 7: 0.000 MH/s (0) 8: 0.000 MH/s (0)

next try with old P106-100 drivers from Asus Website (382.53)
same settings in afterbuner
runs 1hour fine

so i increase the mem to +650 and after 10 minutes again 0 MHs and whole system is slow as fuck and miner needs minutes to close (afterburner also not responsible).

maybe i´m to long out of nvidia stuff - but if i remember correct - Samsung mem should do 650MHz easy

You can try the old kernels via -nvkernel 1 and compare with the new ones (-nvkernel 2) but this should only affect speed, not stability.

Quote from: niask on March 15, 2019, 11:48:37 AM

Is there a point of increasing intensity for 1050Ti to 14?

The hashrate will increase a little but if this is your main GPU (i.e. the display is connected to it), the PC will become almost unusable because of the sluggish redraw of the screen. If the GPU is dedicated to mining (or the entire PC is a mining rig), there is no downside of increasing -mi unless the cards becomes unstable.

Quote from: xolling on March 16, 2019, 05:52:44 AM

Is there any link from 4.0b to this new version Huh

I have a card 1060 6 GB speed increase there?

You can use older Nvidia kernels by specifying -nvkernel 1 and then compare with the new ones (-nvkernel 2).

Quote from: AVP on March 16, 2019, 07:08:56 AM

Automatic fan control ( -tt value) does not seem to work for one my cards (r9 290) does anyone know how to resolve this ?

Please try the new fan control mode (add command-line parameter -fcm 2), or use -fcm 1 to force the old one and see if it makes difference. If not, please send us a log (at least the first ten minutes or so when the card reaches the target temperature) and we will try to find the problem.