Quote from: SamAlackass on May 11, 2019, 12:42:06 PM

Quote from: kamisama233 on May 11, 2019, 03:10:36 AM

thanks for your great tool!

I have one rig it cannot change the any values by your tool

C:\Users\G4560\Desktop\AMT\CLI>WinAMDTweak.exe --i 0 --rfc 175
Successfully applied new RFC settings to GPU 0.

C:\Users\G4560\Desktop\AMT\CLI>WinAMDTweak.exe --i 0 --current
GPU 0: Baffin [Radeon RX 550 640SP / RX 560/560X]
PMG: CKSRE: 2 CKSRX: 2 CKE_PULSE: 10 CKE: 10 SEQ_IDLE: 7
CAS: CL: 22 W2R: 16 R2R: 5 CCLD: 2 R2W: 27 NOPR: 0 NOPW: 0
RAS: RC: 65 RRD: 6 RCDRA: 24 RCDR: 24 RCDWA: 19 RCDW: 19
MISC: RFC: 178 TRP: 24 RP_RDA: 27 RP_WRA: 58
MISC2: WDATATR: 0 T32AW: 0 CRCWL: 25 CRCRL: 3 FAW: 0 PA2WDATA: 0 PA2RDATA: 0
M3(MR4): RAS: 41
DRAM1: RASMACTWR: 9 RASMACTRD: 5 ACTWR: 0 ACTRD: 4
DRAM2: RAS2RAS: 21 RP: 7 WRPLUSRP: 13 BUS_TURN: 9

both cli and gui version have the same problem, the cards was 8 rx 550 4gb micron memory

win10 64, 1607, change several drivers 18.6.1 19.4.X 19.3.X, default or mod bios are the same,

all the same, just can not change any value, when i apply, they just restore to default value, any ideas?

of course, I did it when the rig was mining. I found the bios only have 1500 strap, nothing above the 1500, is it the reason? how to fix it?

That sounds very similar to the issue I'm having, only difference is I usually get no readings from the cards, that's on vegas though. Any value I try to change resets to zero the moment I hit apply too.

The other thing is sometimes it works sometimes it doesn't in my case. I have also noticed it may work at first, enough to set my timings, but if I close the GUI and reopen it I'm back to zero readings and not being able to change anything. Previously set timings stick of course, unless I reboot.

I'm not sure what I'm looking for as this is apparently a rare issue (assuming it is the same issue), but do you see any similarities in our systems? Mine is an older AMD 4 core CPU with an on-board HD 8330, single 4GB stick of DDR3, Win10x64 updated to latest a few days ago. I only use PPT, OverdriveNTool and HWinfo64 to monitor and control the cards and I always install AMD drivers without Wattman/AMD settings or anything. This is a dedicated miner so not much else is installed in terms of software.

I'm going to ditto this as well. I am new to mining again, but have been trying to catch up with the knowledge.
My XFX RX590 is getting 31mh/s with no timing change as it just reverts back to stock. I am able to get mem clock 2500mhz, 950mv and core clock 1360mhz, 950mv with under 140w from the core and chip.

This is my PC btw not dedicated so my guess is that it should be slower than a mining rig, which I'm accounting for in the realm of not trying to blow up my PC. I've seen lower settings with higher hash rates, but I'm trying to stay conservative for now. It's been 3 days of mining so far and I'm enjoying it for now.. (enter Murphy's law)

Edit. And it crashed..