Quote from: DiabloD3 on January 09, 2012, 08:30:21 PM

Quote from: 1onevvolf on January 09, 2012, 07:02:03 PM

Quote from: DiabloD3 on January 09, 2012, 06:10:19 PM

Wait wait wait. Are we sure uint16 is such a good idea? Last time I tried >4 (which was before 2.6, btw, I haven't tested with 2.6), it would crash in the compiler. Also, does anyone have a count on the number of registers per CU? There might not be enough registers to handle that.

I'm not sure if it's a good idea or not so I wanted to measure it Wink

GCN has 64KB worth of registers per CU, and like you said I'm not sure if that's enough. The reason for my curiosity was because GCN's compute units each contain 4 x SIMD units with a width of 16 elements (same size as Larrabee & Intel's MIC, coincidentally), and I recall reading somewhere that each of these SIMD units can retire one 16-way instruction every 4 cycles, so those 16element vectors kind of rang out at me. I also wanted to get familiar with the OpenCL bitcoin mining code and thought it would be a neat exercise (which it was!). Nice code by the way.

I can say for sure that 16element vectors DO compile with the drivers that came with the card.

The -ds code dump for 16 element vectors came out nice and clean, although the last few lines where the result is stored in output seem a bit branchy. It looks something like this:

Code:

if(XG2.s0 == 0x136032ED) { output[Xnonce.s0 & 0xF] = Xnonce.s0; }
if(XG2.s1 == 0x136032ED) { output[Xnonce.s1 & 0xF] = Xnonce.s1; }
if(XG2.s2 == 0x136032ED) { output[Xnonce.s2 & 0xF] = Xnonce.s2; }
...
...
if(XG2.sd == 0x136032ED) { output[Xnonce.sd & 0xF] = Xnonce.sd; }
if(XG2.se == 0x136032ED) { output[Xnonce.se & 0xF] = Xnonce.se; }
if(XG2.sf == 0x136032ED) { output[Xnonce.sf & 0xF] = Xnonce.sf; }

I tried replacing it with a branch-less expression using shuffle() and vstore16() but haven't managed to get it working. What I've come up with looks something like this:

Code:

x mask = Xnonce & 0xF;
x temp = shuffle(select(Xnonce, 0, selection), mask);
vstore16(temp, 0, output);

Anyhow I'm sure that my code modifications are doing all sorts of dumb things. I'm still learning how it all works so please ignore.

Quote from: DiabloD3 on January 09, 2012, 06:10:19 PM

Also, check some of the larger -vs, -v 40 is two sets of uint4 and -v 44 does three uint4s (unlike cgminer, -v 4 does two uint2s).

I've tried all of the different -v settings available (according to the source) but haven't been able to get any higher than the 666MH/s with the default settings and 3 compute threads.

The branching has ended up becoming the best outcome. It can evaluate those branches in parallel, and you can't easily optimize away branches for memory writes (and theres apparently like 2 or 3 good tricks to get rid of branch waste, its just none of them work on memory writes).

I should look at shuffle. Your way doesn't quite work though, vstore would output H !=0 hashes, which would trigger HW error alerts (and rightfully so) in the host code, and I consider the HW error tracking important. At least, assuming I'm reading that code right, anyways.

I'll go add official 8 and 16 wide support in a bit, should be useful on, say, AVX if you manually enable CPU mining in the code. SDK 2.6's cpu compiler apparently has gotten a lot better from what I've heard.

So does that mean that is the best for 5870 cards ? Or stick to 2.1 or 2.4 ? I am quite confused as to what the best SDK / ati driver combo is ATM.