Quote from: Searing on July 27, 2014, 02:28:07 AM

Quote from: BitCoin Operated Boy on July 26, 2014, 11:12:23 PM

Quote from: antirack on July 26, 2014, 11:03:19 PM

Quote from: BitCoin Operated Boy on July 26, 2014, 09:18:57 PM

I have just peeked into my fuse box and it says that the circuit breaker for the mains sockets is 32A.

You need to know the amperage of the circuit breaker where you connect the SP30 to, or each of the power supplies. Not the main breaker.

Ok so also, I would need to buy separate circuit breakers for each SP30?
Would you have any good recommendation from e-bay maybe?
I appreciate your help. I'm not very electric savvy

myself in USA I simply have 1 220v circuit wired with 12avg wire rated at 20 amps with a 20 amp 220v double pole breaker and of course the 220v plug at the wall...to do so
into an ISOBAR Euro4 version surge protector 4 volt....here off amazon..I have 3 total 220v plugs/circuits and an isobar euro4 on each one...

http://www.amazon.com/Tripp-Lite-EURO-4-International-Protector/dp/B00006HZ4M/ref=sr_1_3?ie=UTF8&qid=1406427314&sr=8-3&keywords=euro+4

it is cheaper then a PDU and works for my needs...

this was easy to do because in my case it is in the bsmt near the panel..so what the heck overkill....1 power supply of the 2 on the sp30 will be plugged
into the above 20amp breaker/20 amp socket/indv 220v euro4 isobar for each 20amp line/breaker (again this model eruo4 at 220v because the sp30 comes
with cords that work for this)

YOU DO need however to purchase the 220v cord from the power outlet to the euro4 isobar..(it has interchangeable cords) the euro4 comes with the
same type of cord as the sp30 miners will come with...not the one that goes from the 220v isobar to the plug in the wall..you need to match (see below)

below is cords that come with the sp30 and the isobar euro4 above (at least the end that does not plug into the sp30 power supply that can be a different type)

http://www.amazon.com/gp/product/B003MG9F78/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

below here is the 3 220v cords from the isobar4 4 surge protector to the plug on the wall...

http://www.amazon.com/gp/product/B0093WFT5C/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

so yeah way over kill but....should work fine 3 circuits using 3 euro4 isobars...1 for each power supply on the sp30 and 1 for the KNC Titan if/when it comes

again overkill but what the heck...as to the tripplite isobars ...well they have saved my butt before so better safe then sorry...
and again cheaper then a PDU

(silly hobby I could have got a bass boat and it probably would have sunk....with my luck anyway..go figure....toys..toys...toys...)

Searing

Thank you for your advice.
It looks like Isobar is a very good solution. I just nee to buy 230v version (United Kingdom) and also relveant UK socket cables.

Quote from: Spondoolies-Tech on July 27, 2014, 05:06:37 AM

Quote from: grn on July 27, 2014, 04:58:12 AM

...
EDIT: I understand running a new business is difficult and when things dont work out its even tougher. You will always do better by being upfront and communicating promptly. keep up your efforts and communicate more, it would be nice to see you succeed.

We're communicating. We don't want to give inaccurate information. Stabilizing new system and new firmware takes time. Stress testing the systems also takes time.
I repeat my original request, please be patient.

Guy

I sent you e-mail about voltage over a week ago but you have not replied...

Also could you please ellaborate on:

"Please realize these miners are built to be hosted in an industrial environment. Before you plug these in consult an electrician and make sure to get permits/inspection for any work done...
...These are not home miners like bitmain are, they really need to be in a data centre. A cost you must have calculated on your pre-purchase ROI analysis. "