Search content
Sort by
Showing 20 of 26 results by deafgoose
Re: S19j Pro 104th chips state is "normal" but wont hash???
I got my sd-card adapter. Apparently its USB 3.0 but luckily 3.0 is backwards compatible all the way down to 1.1.
I flashed the image onto the adapter, stuck it in, booted it up and nothing. I go to the ip address and its still the old firmware.
From my understanding, it should have auto-installed after boot-up...
I flashed the image onto the adapter, stuck it in, booted it up and nothing. I go to the ip address and its still the old firmware.
From my understanding, it should have auto-installed after boot-up...
Re: S19j Pro 104th chips state is "normal" but wont hash???
The issue from logs still the same as from your previous logs removing the 3rd hashboard and keeping the two hashboards should run normally with decrease hashrate.
As suggested by mikeywith you can try Braiins OS to test if it is just an EEPROM issue but the problem is as you said before that it does not have the SD card slot have you checked the control board inside and maybe the SD card slot is hiding near Ethernet socket or beaglebone ?
Or if does not have an SD slot then your last hope is to use an OTG drive to micro USB to boot Braiins OS in your unit.
Don't you find it strange that its defective yet no issue with my logs?
I am very unlucky. I dont have the sd-card version. I will order the adapter and load up Braiins OS and report back. Thanks!
Re: S19j Pro 104th chips state is "normal" but wont hash???
ARE YOU USA BASED?
There are a few good repair guys that can turn your gear around fast.
If you deal directly with Bitmain they can be very slow.
You end up with all three boards turned off for a month or more.
There are a few good repair guys that can turn your gear around fast.
If you deal directly with Bitmain they can be very slow.
You end up with all three boards turned off for a month or more.
Nope, Canada.
UPDATE: All 3 hash boards stopped working today. WTF?
Maybe now somebody will see something in my logs? I would be so grateful to anyone that could shine some light on this issue.
THANK-YOU!!!!
Code:
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000@0] On node 0 totalpages: 65536
[ 0.000000@0] DMA zone: 1024 pages used for memmap
[ 0.000000@0] DMA zone: 0 pages reserved
[ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok!
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016903@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036437@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[ 0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[ 0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[ 0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[ 0.106464@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114386@0] SELinux: Starting in permissive mode
[ 0.114422@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121106@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128833@0] ftrace: allocating 30061 entries in 118 pages
[ 0.186737@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.187549@0] CPU0: update cpu_capacity 1024
[ 0.191876@0] ASID allocator initialised with 32768 entries
[ 0.230013@0] secmon: can't fine clear_range
[ 0.230217@0] EFI services will not be available.
[ 0.233481@0] Meson chip version = RevC (25:C - 23:0)
[ 0.267152@1] Detected VIPT I-cache on CPU1
[ 0.267212@1] CPU1: update cpu_capacity 1024
[ 0.267214@1] CPU1: Booted secondary processor [410fd034]
[ 0.295218@2] Detected VIPT I-cache on CPU2
[ 0.295272@2] CPU2: update cpu_capacity 1024
[ 0.295274@2] CPU2: Booted secondary processor [410fd034]
[ 0.323277@3] Detected VIPT I-cache on CPU3
[ 0.323326@3] CPU3: update cpu_capacity 1024
[ 0.323328@3] CPU3: Booted secondary processor [410fd034]
[ 0.323414@0] Brought up 4 CPUs
[ 0.362635@0] SMP: Total of 4 processors activated.
[ 0.367544@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.373580@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.384130@0] CPU: All CPU(s) started at EL2
[ 0.385319@0] alternatives: patching kernel code
[ 0.390622@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.397843@0] devtmpfs: initialized
[ 0.412826@0] DMI not present or invalid.
[ 0.413183@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.421191@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.427773@0] pinctrl core: initialized pinctrl subsystem
[ 0.434160@0] NET: Registered protocol family 16
[ 0.457724@0] cpuidle: using governor menu
[ 0.458208@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.463831@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.471238@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.477373@0] clkmsr: clkmsr: driver init
[ 0.481437@0] aml_watch_point_probe, in, wp:2
[ 0.486017@0] pstore: using zlib compression
[ 0.490279@0] console [pstore-1] enabled
[ 0.493711@0] pstore: Registered ramoops as persistent store backend
[ 0.500119@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[ 0.514478@0] aml_iomap: amlogic iomap probe done
[ 0.521284@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.523218@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.623488@0] usbcore: registered new interface driver usbfs
[ 0.623658@0] usbcore: registered new interface driver hub
[ 0.629255@0] usbcore: registered new device driver usb
[ 0.634557@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.639502@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.648888@0] PTP clock support registered
[ 0.653234@0] dmi: Firmware registration failed.
[ 0.662031@0] secmon: reserve_mem_size:0x300000
[ 0.662208@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.669179@0] secmon: get page:ffffffbf00140000, 5000
[ 0.673866@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.682251@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.690135@0] NetLabel: Initializing
[ 0.692301@0] NetLabel: domain hash size = 128
[ 0.696886@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.702116@0] NetLabel: unlabeled traffic allowed by default
[ 0.708720@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.835576@0] VFS: Disk quotas dquot_6.6.0
[ 0.835723@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.861760@0] NET: Registered protocol family 2
[ 0.862796@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.867993@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.874685@0] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.881251@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.887209@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.893970@0] NET: Registered protocol family 1
[ 0.898933@0] RPC: Registered named UNIX socket transport module.
[ 0.904357@0] RPC: Registered udp transport module.
[ 0.909232@0] RPC: Registered tcp transport module.
[ 0.914142@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.923250@0] Unpacking initramfs...
[ 1.423727@3] Initramfs unpacking failed: junk in compressed archive
[ 1.430557@3] Freeing initrd memory: 6572K
[ 1.431427@3] hw perfevents: clusterb_enabled = 0
[ 1.433808@3] hw perfevents: cpumasks 0xf, 0x0
[ 1.438279@3] hw perfevents: cluster A irq = 7
[ 1.442850@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.452992@3] audit: initializing netlink subsys (disabled)
[ 1.456338@3] audit: type=2000 audit(1.268:1): initialized
[ 1.463656@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.487455@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.490410@3] NFS: Registering the id_resolver key type
[ 1.493169@3] Key type id_resolver registered
[ 1.497492@3] Key type id_legacy registered
[ 1.502139@3] fuse init (API version 7.26)
[ 1.507475@3] SELinux: Registering netfilter hooks
[ 1.513893@3] NET: Registered protocol family 38
[ 1.513954@3] Key type asymmetric registered
[ 1.517202@3] Asymmetric key parser 'x509' registered
[ 1.522670@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.529896@3] io scheduler noop registered (default)
[ 1.534946@3] io scheduler deadline registered
[ 1.539666@3] io scheduler cfq registered
[ 1.560136@0] random: fast init done
[ 1.560236@0] random: crng init done
[ 1.561690@3] Unable to detect cache hierarchy for CPU 0
[ 1.603269@3] loop: module loaded
[ 1.604755@3] zram: Added device: zram0
[ 1.605167@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.612043@3] libphy: Fixed MDIO Bus: probed
[ 1.616605@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.621026@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.629273@3] ee eth reset:Addr = ffffff80081fd008
[ 1.636657@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.638689@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.643929@3] Ring mode enabled
[ 1.647160@3] DMA HW capability register supported
[ 1.651890@3] Normal descriptors
[ 1.655205@3] RX Checksum Offload Engine supported
[ 1.660111@3] COE Type 2
[ 1.662731@3] TX Checksum insertion supported
[ 1.667193@3] Wake-Up On Lan supported
[ 1.671135@3] Enable RX Mitigation via HW Watchdog Timer
[ 1.684635@3] libphy: stmmac: probed
[ 1.684688@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[ 1.691108@3] PPP generic driver version 2.4.2
[ 1.694120@3] PPP BSD Compression module registered
[ 1.698623@3] PPP Deflate Compression module registered
[ 1.703884@3] PPP MPPE Compression module registered
[ 1.708838@3] NET: Registered protocol family 24
[ 1.714332@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.720235@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.727285@3] usbcore: registered new interface driver cdc_acm
[ 1.732480@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.740916@3] usbcore: registered new interface driver usbserial
[ 1.747574@3] mousedev: PS/2 mouse device common for all mice
[ 1.753069@3] usbcore: registered new interface driver xpad
[ 1.758444@3] i2c /dev entries driver
[ 1.763218@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.767445@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.778396@3] ff803000.serial: clock gate not found
[ 1.779948@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[ 1.787189@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[ 1.802097@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 1.804800@3] console [ttyS0] enabled
[ 1.812016@3] bootconsole [aml_uart0] disabled
[ 1.821693@2] ff804000.serial: clock gate not found
[ 1.825820@2] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[ 1.832926@2] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 1.843326@1] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[ 1.849423@1] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[ 1.859582@3] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[ 1.865881@3] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[ 1.876861@2] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[ 1.886120@2] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[ 1.892623@2] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[ 1.907607@2] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.911489@2] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.923835@2] aml_dma ff63e000.aml_dma: Aml dma
[ 1.927005@2] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[ 1.931949@2] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 1.938308@2] efusekeynum: 4
[ 1.940642@2] efusekeyname: mac offset: 0 size: 6
[ 1.947086@2] efusekeyname: mac_bt offset: 6 size: 6
[ 1.953505@2] efusekeyname: mac_wifi offset: 12 size: 6
[ 1.959906@2] efusekeyname: usid offset: 18 size: 16
[ 1.966741@1] efuse efuse: probe OK!
[ 1.972170@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 1.979424@0] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode
[ 1.984495@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 1.989731@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[ 2.036866@0] meson-mmc: meson_mmc_probe() : success!
[ 2.037149@0] amlogic mtd driver init
[ 2.041183@0] prase_get_dtb_nand_parameter:128,parse dts start
[ 2.045933@0] bl mode descrete
[ 2.048812@0] fip_copies 4
[ 2.051477@0] fip_size 0x200000
[ 2.054616@0] nand_clk_ctrl 0xffe07000
[ 2.058341@0] prase_get_dtb_nand_parameter:234,parse dts end
[ 2.064007@0] nand_clk_ctrl 0xffe07000
[ 2.067728@0] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[ 2.076538@0] plat->aml_nand_device ffffff800a005c10
[ 2.080639@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.086703@0] NAND device id: 2c da 90 95 6 0
[ 2.090764@0] NAND device: Manufacturer ID:
[ 2.094830@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.101873@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.107306@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.112854@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.119099@0] mtd->oobavail: 0x8
[ 2.122508@0] aml_nand_init 2119: plat-name:bootloader
[ 2.127418@0] Creating 1 MTD partitions on "bootloader":
[ 2.132722@0] 0x000000000000-0x000000200000 : "bootloader"
[ 2.141587@0] bootloader initialized ok
[ 2.141966@0] plat->aml_nand_device ffffff800a005c10
[ 2.146951@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.153086@0] NAND device id: 2c da 90 95 6 0
[ 2.157063@0] NAND device: Manufacturer ID:
[ 2.161139@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.168173@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.173614@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.179154@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.185406@0] mtd->oobavail: 0x8
[ 2.188861@0] aml_nand_init 2119: plat-name:nandnormal
[ 2.193765@0] bbt_start=20
[ 2.196381@0] env_start=24
[ 2.199095@0] key_start=32
[ 2.201774@0] dtb_start=40
[ 2.204440@0] ddr_start=44
[ 2.207169@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[ 2.213641@0] get_free_node 43: bitmap=0
[ 2.217114@0] get_free_node 55: bitmap=1
[ 2.221206@0] get_free_node 43: bitmap=1
[ 2.224913@0] get_free_node 55: bitmap=3
[ 2.229005@0] get_free_node 43: bitmap=3
[ 2.232695@0] get_free_node 55: bitmap=7
[ 2.236597@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[ 2.243284@0] nbbt free list:
[ 2.246231@0] blockN=21, ec=-1, dirty_flag=0
[ 2.250478@0] blockN=22, ec=-1, dirty_flag=0
[ 2.254724@0] blockN=23, ec=-1, dirty_flag=0
[ 2.258972@0] aml_nand_scan_rsv_info 1141: page_num=1
[ 2.264381@0] nbbt valid addr: 280000
[ 2.267641@0] aml_nand_bbt_check 1306 bbt is valid, reading.
[ 2.273272@0] aml_nand_read_rsv_info:423,read nbbt info at 280000
[ 2.279534@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[ 2.285962@0] get_free_node 43: bitmap=7
[ 2.289480@0] get_free_node 55: bitmap=f
[ 2.293571@0] get_free_node 43: bitmap=f
[ 2.297280@0] get_free_node 55: bitmap=1f
[ 2.301458@0] get_free_node 43: bitmap=1f
[ 2.305253@0] get_free_node 55: bitmap=3f
[ 2.309431@0] get_free_node 43: bitmap=3f
[ 2.313226@0] get_free_node 55: bitmap=7f
[ 2.317405@0] get_free_node 43: bitmap=7f
[ 2.321199@0] get_free_node 55: bitmap=ff
[ 2.325377@0] get_free_node 43: bitmap=ff
[ 2.329173@0] get_free_node 55: bitmap=1ff
[ 2.333438@0] get_free_node 43: bitmap=1ff
[ 2.337320@0] get_free_node 55: bitmap=3ff
[ 2.341393@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[ 2.348063@0] nenv free list:
[ 2.351011@0] blockN=25, ec=-1, dirty_flag=0
[ 2.355257@0] blockN=26, ec=-1, dirty_flag=0
[ 2.359504@0] blockN=27, ec=-1, dirty_flag=0
[ 2.363751@0] blockN=28, ec=-1, dirty_flag=0
[ 2.367997@0] blockN=29, ec=-1, dirty_flag=0
[ 2.372244@0] blockN=30, ec=-1, dirty_flag=0
[ 2.376491@0] blockN=31, ec=-1, dirty_flag=0
[ 2.380738@0] aml_nand_scan_rsv_info 1141: page_num=32
[ 2.398000@0] nenv valid addr: 310000
[ 2.398034@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[ 2.402392@0] get_free_node 43: bitmap=3ff
[ 2.406272@0] get_free_node 55: bitmap=7ff
[ 2.410537@0] get_free_node 43: bitmap=7ff
[ 2.414418@0] get_free_node 55: bitmap=fff
[ 2.418683@0] get_free_node 43: bitmap=fff
[ 2.422565@0] get_free_node 55: bitmap=1fff
[ 2.426917@0] get_free_node 43: bitmap=1fff
[ 2.430885@0] get_free_node 55: bitmap=3fff
[ 2.435236@0] get_free_node 43: bitmap=3fff
[ 2.439205@0] get_free_node 55: bitmap=7fff
[ 2.443556@0] get_free_node 43: bitmap=7fff
[ 2.447525@0] get_free_node 55: bitmap=ffff
[ 2.451876@0] get_free_node 43: bitmap=ffff
[ 2.455845@0] get_free_node 55: bitmap=1ffff
[ 2.460282@0] get_free_node 43: bitmap=1ffff
[ 2.464338@0] get_free_node 55: bitmap=3ffff
[ 2.468585@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.475255@0] nkey free list:
[ 2.478203@0] blockN=32, ec=-1, dirty_flag=0
[ 2.482450@0] blockN=33, ec=-1, dirty_flag=0
[ 2.486696@0] blockN=34, ec=-1, dirty_flag=0
[ 2.490942@0] blockN=35, ec=-1, dirty_flag=0
[ 2.495189@0] blockN=36, ec=-1, dirty_flag=0
[ 2.499436@0] blockN=37, ec=-1, dirty_flag=0
[ 2.503683@0] blockN=38, ec=-1, dirty_flag=0
[ 2.507929@0] blockN=39, ec=-1, dirty_flag=0
[ 2.512176@0] aml_nand_scan_rsv_info 1141: page_num=16
[ 2.517289@0] nkey valid addr: fffffffffffe0000
[ 2.521798@0] aml_nand_key_check 1251 NO key exist
[ 2.526564@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[ 2.533185@0] get_free_node 43: bitmap=3ffff
[ 2.537052@0] get_free_node 55: bitmap=7ffff
[ 2.541490@0] get_free_node 43: bitmap=7ffff
[ 2.545545@0] get_free_node 55: bitmap=fffff
[ 2.549983@0] get_free_node 43: bitmap=fffff
[ 2.554038@0] get_free_node 55: bitmap=1fffff
[ 2.558372@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[ 2.565042@0] ndtb free list:
[ 2.567973@0] blockN=41, ec=-1, dirty_flag=0
[ 2.572236@0] blockN=42, ec=-1, dirty_flag=0
[ 2.576483@0] blockN=43, ec=-1, dirty_flag=0
[ 2.580730@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.598036@0] ndtb valid addr: 500000
[ 2.598070@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[ 2.602510@0] get_free_node 43: bitmap=1fffff
[ 2.606654@0] get_free_node 55: bitmap=3fffff
[ 2.611178@0] get_free_node 43: bitmap=3fffff
[ 2.615320@0] get_free_node 55: bitmap=7fffff
[ 2.619653@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.626324@0] nddr free list:
[ 2.629271@0] blockN=44, ec=-1, dirty_flag=0
[ 2.633518@0] blockN=45, ec=-1, dirty_flag=0
[ 2.637765@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.642878@0] nddr valid addr: fffffffffffe0000
[ 2.647385@0] aml_nand_ddr_check 1281 NO ddr exist
[ 2.652155@0] tpl: off 8388608, size 8388608
[ 2.783826@0] Creating 6 MTD partitions on "nandnormal":
[ 2.783873@0] 0x000000800000-0x000001000000 : "tpl"
[ 2.795063@1] 0x000001000000-0x000001200000 : "misc"
[ 2.798192@2] 0x000001200000-0x000002200000 : "recovery"
[ 2.810242@2] 0x000002200000-0x000004200000 : "boot"
[ 2.829401@2] 0x000004200000-0x000004700000 : "config"
[ 2.834074@2] 0x000004700000-0x000010000000 : "nvdata"
[ 2.935098@0] nandnormal initialized ok
[ 2.935206@0] aml_ubootenv_init: register env chardev
[ 2.938937@0] aml_ubootenv_init: register env chardev OK
[ 2.943777@0] amlnf_dtb_init: register dtb cdev
[ 2.948751@0] amlnf_dtb_init: register dtd cdev OK
[ 2.952948@0] mtd_nand_probe 267 , err = 0
[ 2.958073@1] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[ 2.963525@1] input: aml_vkeypad as /devices/platform/rtc/input/input0
[ 2.970695@0] unifykey: storage in base: 0xffffffc005000000
[ 2.975132@0] unifykey: storage out base: 0xffffffc005040000
[ 2.980736@0] unifykey: storage block base: 0xffffffc005080000
[ 2.986536@0] unifykey: probe done!
[ 2.990733@0] unifykey: no efuse-version set, use default value: -1
[ 2.996262@0] unifykey: key unify config unifykey-num is 6
[ 3.001791@0] unifykey: key unify fact unifykey-num is 6
[ 3.006997@0] unifykey: unifykey_devno: f200000
[ 3.012184@0] unifykey: device unifykeys created ok
[ 3.016483@0] unifykey: aml_unifykeys_init done!
[ 3.021387@0] sysled: module init
[ 3.024884@0] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 3.029635@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 3.037067@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 3.045764@1] dmc_monitor_probe
[ 3.051602@1] defendkey defendkey: Reserved memory is not enough!
[ 3.052329@1] defendkey: probe of defendkey failed with error -22
[ 3.058760@1] GACT probability NOT on
[ 3.062087@1] Mirror/redirect action on
[ 3.065865@1] u32 classifier
[ 3.068680@1] Actions configured
[ 3.072258@1] Netfilter messages via NETLINK v0.30.
[ 3.077540@1] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 3.083734@1] ctnetlink v0.93: registering with nfnetlink.
[ 3.089610@1] xt_time: kernel timezone is -0000
[ 3.093328@1] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 3.099962@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.104642@1] arp_tables: arp_tables: (C) 2002 David S. Miller
[ 3.110134@1] Initializing XFRM netlink socket
[ 3.115657@1] NET: Registered protocol family 10
[ 3.121399@1] mip6: Mobile IPv6
[ 3.122205@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.128182@1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.136144@1] NET: Registered protocol family 17
[ 3.138458@1] NET: Registered protocol family 15
[ 3.143055@1] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.156196@1] l2tp_core: L2TP core driver, V2.0
[ 3.160592@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.165510@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 3.171261@1] l2tp_netlink: L2TP netlink interface
[ 3.176070@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 3.182143@1] l2tp_debugfs: L2TP debugfs support
[ 3.186654@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 3.193315@1] NET: Registered protocol family 35
[ 3.198232@1] Key type dns_resolver registered
[ 3.202794@1] Registered swp emulation handler
[ 3.206696@1] Registered cp15_barrier emulation handler
[ 3.211887@1] Registered setend emulation handler
[ 3.216630@1] disable EAS feature
[ 3.221612@1] registered taskstats version 1
[ 3.237799@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 3.744209@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.744296@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.752579@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[ 3.761021@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[ 3.768494@1] hub 1-0:1.0: USB hub found
[ 3.770979@1] hub 1-0:1.0: 1 port detected
[ 3.775569@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.780597@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.788491@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.797981@2] hub 2-0:1.0: USB hub found
[ 3.800549@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.807903@2] usb usb2: Unsupported the hub
[ 3.812636@2] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
[ 3.820742@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d173000)
[ 3.820820@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 3.828672@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[ 3.828684@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb27e00
[ 3.929280@2] dwc_otg: Core Release: 3.10a
[ 3.929334@2] dwc_otg: Setting default values for core params
[ 3.933530@2] dwc_otg: curmode: 0, host_only: 0
[ 3.938033@2] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[ 3.950538@2] dwc_otg: Using Buffer DMA mode
[ 3.950576@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 3.954484@2] dwc_otg: Working on port type = SLAVE
[ 3.959341@2] dwc_otg: Dedicated Tx FIFOs mode
[ 3.966279@2] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[ 3.973052@2] cpucore_cooling_register, max_cpu_core_num:4
[ 3.985266@0] gxbb_pm: enter meson_pm_probe!
[ 3.985324@0] no vddio3v3_en pin
[ 3.986975@0] pm-meson aml_pm: Can't get switch_clk81
[ 3.992074@0] gxbb_pm: meson_pm_probe done
[ 3.997041@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.003308@0] Freeing unused kernel memory: 3648K
[ 4.017619@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.269025@0] ubi0: attaching mtd5
[ 4.287552@0] ubi0: scanning is finished
[ 4.292113@3] ubi0: attached mtd5 (name "config", size 5 MiB)
[ 4.292242@3] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.299323@3] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.306209@3] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.313321@3] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[ 4.319381@3] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 4.326757@3] ubi0: max/mean erase counter: 10/5, WL threshold: 4096, image sequence number: 4272682163
[ 4.336106@3] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[ 4.345329@0] ubi0: background thread "ubi_bgt0d" started, PID 1076
[ 4.358538@1] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[ 4.375136@2] UBIFS (ubi0:0): recovery needed
[ 4.426251@0] UBIFS (ubi0:0): recovery completed
[ 4.426509@0] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[ 4.433261@0] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 4.443301@0] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 4.453522@0] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[ 4.460111@0] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID DF678CD6-72B3-440D-AD49-B5CACA89C146, small LPT model
[ 4.484804@0] ubi2: attaching mtd6
[ 5.158140@0] ubi2: scanning is finished
[ 5.165564@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[ 5.165868@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.172922@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.179845@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.186950@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[ 5.193186@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.200546@1] ubi2: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 3925779084
[ 5.209826@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[ 5.219200@3] ubi2: background thread "ubi_bgt2d" started, PID 1087
[ 5.232088@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091
[ 5.248767@0] UBIFS (ubi2:0): recovery needed
[ 5.296598@0] UBIFS (ubi2:0): recovery completed
[ 5.296903@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[ 5.303591@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.313643@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[ 5.324469@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[ 5.331233@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID D3E2E49A-3C02-4261-9EEF-3A2DAF328DBD, small LPT model
[ 5.551613@3] eth0: device MAC address 02:5a:b9:1d:92:fb
[ 5.633822@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 5.635120@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.886634@0] uart_trans: loading out-of-tree module taints kernel.
[ 5.889260@0] register uart_trans chrdev success.
[ 5.892442@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[ 5.900442@0] tty port open success [/dev/ttyS3]!
[ 5.904869@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[ 5.913386@0] init sucess for tty struct (246:3) [/dev/ttyS3]
[ 5.919339@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[ 5.926993@0] tty port open success [/dev/ttyS2]!
[ 5.931635@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[ 5.940103@0] init sucess for tty struct (246:2) [/dev/ttyS2]
[ 5.946228@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[ 5.953877@0] tty port open success [/dev/ttyS1]!
[ 5.958524@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[ 5.966946@0] init sucess for tty struct (246:1) [/dev/ttyS1]
[ 5.973018@0] create workqueue success!
[ 7.672988@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 7.676278@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.284909@1] uart trans dev open.
[ 32.285019@1] uart_buf virt addr = 0xffffffc00b1c0000
[ 32.287724@1] uart_buf phys addr = 0x0b1c0000
[ 32.292108@1] uart_buf pfn = 0x0000b1c0
[ 32.296926@1] uart trans stop send work timer.
[ 32.301098@1] uart trans set chain exist bits:0x7.
[ 32.305607@1] uart trans set work queue count 768.
[ 83.119658@3] uart set baud to: 4098
[ 83.119718@3] uart set baud to: 4098
[ 83.121230@3] uart set baud to: 4098
[ 96.236632@2] uart trans stop send work timer.
[ 98.947924@3] uart trans start send work timer.
[ 301.722926@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead.
===========================================Miner log===========================================
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 3
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 chain id = 0
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 chain id = 1
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 3
2015-01-01 00:00:21 skip loading levels for now
2023-06-16 22:30:25 load chain 0 eeprom data
2023-06-16 22:30:29 load chain 1 eeprom data
2023-06-16 22:30:32 load chain 2 eeprom data
2023-06-16 22:30:32 i2c_sim_init start
2023-06-16 22:30:32 init gpio477
2023-06-16 22:30:32 init gpio476
2023-06-16 22:30:32 i2c_sim_init end
2023-06-16 22:30:33 power open power_version = 0x76
2023-06-16 22:30:36 power is not Calibrated
2023-06-16 22:30:37 miner type: Antminer S19j Pro
2023-06-16 22:30:37 multi machine mode
2023-06-16 22:30:37 load machine BHB42631 conf
2023-06-16 22:30:37 machine : BHB42631
2023-06-16 22:30:37 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 fan_eft : 0 fan_pwm : 100
2023-06-16 22:30:37 create thread get_nonce_and_register_thread
2023-06-16 22:30:37 fixed working voltage = 1380
2023-06-16 22:30:37 fixed frequency is 525
2023-06-16 22:30:37 Chain [0] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [0] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [1] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [1] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [2] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [2] BOM Version: 0x0010
2023-06-16 22:30:37 bad chain id = 3
2023-06-16 22:30:37 Fan check passed.
2023-06-16 22:30:37 uart_trans addr:0xf43df000.
2023-06-16 22:30:37 max sensor num = 4
2023-06-16 22:30:37 STATUS_INITED: soc init done!
2023-06-16 22:30:37 temperature_monitor_thread start...
2023-06-16 22:30:40 start to init...
2023-06-16 22:30:40 warning:power is not calibration.
2023-06-16 22:30:41 power type version: 0x0076
2023-06-16 22:30:43 disable power watchdog: 0x0000
2023-06-16 22:30:44 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-16 22:31:15 Slept 30 seconds, diff = 0.
2023-06-16 22:31:19 set_voltage_by_steps to 1500.
2023-06-16 22:31:28 start up min temp by 75a = 24
2023-06-16 22:31:31 Chain[0]: find 126 asic, times 0
2023-06-16 22:31:33 Chain[1]: find 126 asic, times 0
2023-06-16 22:31:35 Chain[2]: find 0 asic, times 0
2023-06-16 22:31:37 Chain[2]: find 0 asic, times 1
2023-06-16 22:31:38 Chain[2]: find 0 asic, times 2
2023-06-16 22:31:38 Chain 2 only find 0 asic, will power off hash board 2
2023-06-16 22:31:38 ERROR_SOC_INIT: soc init failed!
2023-06-16 22:31:38 stop_mining: soc init failed!
2023-06-16 22:31:38 uninit_temp_info
2023-06-16 22:31:38 do not read temp anymore...
2023-06-16 22:31:38 cancel thread
2023-06-16 22:31:38 ****power off hashboard****
2023-06-16 22:31:39 temp monitor thread exit
2023-06-16 22:31:44 Version num 65536
2023-06-16 22:31:44 Mask num 0x1fffe000
2023-06-16 22:31:44 opt_multi_version = 65536, interval timeout = 2945120
2023-06-16 22:31:44 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000@0] On node 0 totalpages: 65536
[ 0.000000@0] DMA zone: 1024 pages used for memmap
[ 0.000000@0] DMA zone: 0 pages reserved
[ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok!
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016903@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036437@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[ 0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[ 0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[ 0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[ 0.106464@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114386@0] SELinux: Starting in permissive mode
[ 0.114422@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121106@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128833@0] ftrace: allocating 30061 entries in 118 pages
[ 0.186737@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.187549@0] CPU0: update cpu_capacity 1024
[ 0.191876@0] ASID allocator initialised with 32768 entries
[ 0.230013@0] secmon: can't fine clear_range
[ 0.230217@0] EFI services will not be available.
[ 0.233481@0] Meson chip version = RevC (25:C - 23:0)
[ 0.267152@1] Detected VIPT I-cache on CPU1
[ 0.267212@1] CPU1: update cpu_capacity 1024
[ 0.267214@1] CPU1: Booted secondary processor [410fd034]
[ 0.295218@2] Detected VIPT I-cache on CPU2
[ 0.295272@2] CPU2: update cpu_capacity 1024
[ 0.295274@2] CPU2: Booted secondary processor [410fd034]
[ 0.323277@3] Detected VIPT I-cache on CPU3
[ 0.323326@3] CPU3: update cpu_capacity 1024
[ 0.323328@3] CPU3: Booted secondary processor [410fd034]
[ 0.323414@0] Brought up 4 CPUs
[ 0.362635@0] SMP: Total of 4 processors activated.
[ 0.367544@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.373580@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.384130@0] CPU: All CPU(s) started at EL2
[ 0.385319@0] alternatives: patching kernel code
[ 0.390622@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.397843@0] devtmpfs: initialized
[ 0.412826@0] DMI not present or invalid.
[ 0.413183@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.421191@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.427773@0] pinctrl core: initialized pinctrl subsystem
[ 0.434160@0] NET: Registered protocol family 16
[ 0.457724@0] cpuidle: using governor menu
[ 0.458208@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.463831@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.471238@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.477373@0] clkmsr: clkmsr: driver init
[ 0.481437@0] aml_watch_point_probe, in, wp:2
[ 0.486017@0] pstore: using zlib compression
[ 0.490279@0] console [pstore-1] enabled
[ 0.493711@0] pstore: Registered ramoops as persistent store backend
[ 0.500119@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[ 0.514478@0] aml_iomap: amlogic iomap probe done
[ 0.521284@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.523218@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.623488@0] usbcore: registered new interface driver usbfs
[ 0.623658@0] usbcore: registered new interface driver hub
[ 0.629255@0] usbcore: registered new device driver usb
[ 0.634557@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.639502@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.648888@0] PTP clock support registered
[ 0.653234@0] dmi: Firmware registration failed.
[ 0.662031@0] secmon: reserve_mem_size:0x300000
[ 0.662208@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.669179@0] secmon: get page:ffffffbf00140000, 5000
[ 0.673866@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.682251@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.690135@0] NetLabel: Initializing
[ 0.692301@0] NetLabel: domain hash size = 128
[ 0.696886@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.702116@0] NetLabel: unlabeled traffic allowed by default
[ 0.708720@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.835576@0] VFS: Disk quotas dquot_6.6.0
[ 0.835723@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.861760@0] NET: Registered protocol family 2
[ 0.862796@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.867993@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.874685@0] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.881251@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.887209@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.893970@0] NET: Registered protocol family 1
[ 0.898933@0] RPC: Registered named UNIX socket transport module.
[ 0.904357@0] RPC: Registered udp transport module.
[ 0.909232@0] RPC: Registered tcp transport module.
[ 0.914142@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.923250@0] Unpacking initramfs...
[ 1.423727@3] Initramfs unpacking failed: junk in compressed archive
[ 1.430557@3] Freeing initrd memory: 6572K
[ 1.431427@3] hw perfevents: clusterb_enabled = 0
[ 1.433808@3] hw perfevents: cpumasks 0xf, 0x0
[ 1.438279@3] hw perfevents: cluster A irq = 7
[ 1.442850@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.452992@3] audit: initializing netlink subsys (disabled)
[ 1.456338@3] audit: type=2000 audit(1.268:1): initialized
[ 1.463656@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.487455@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.490410@3] NFS: Registering the id_resolver key type
[ 1.493169@3] Key type id_resolver registered
[ 1.497492@3] Key type id_legacy registered
[ 1.502139@3] fuse init (API version 7.26)
[ 1.507475@3] SELinux: Registering netfilter hooks
[ 1.513893@3] NET: Registered protocol family 38
[ 1.513954@3] Key type asymmetric registered
[ 1.517202@3] Asymmetric key parser 'x509' registered
[ 1.522670@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.529896@3] io scheduler noop registered (default)
[ 1.534946@3] io scheduler deadline registered
[ 1.539666@3] io scheduler cfq registered
[ 1.560136@0] random: fast init done
[ 1.560236@0] random: crng init done
[ 1.561690@3] Unable to detect cache hierarchy for CPU 0
[ 1.603269@3] loop: module loaded
[ 1.604755@3] zram: Added device: zram0
[ 1.605167@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.612043@3] libphy: Fixed MDIO Bus: probed
[ 1.616605@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.621026@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.629273@3] ee eth reset:Addr = ffffff80081fd008
[ 1.636657@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.638689@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.643929@3] Ring mode enabled
[ 1.647160@3] DMA HW capability register supported
[ 1.651890@3] Normal descriptors
[ 1.655205@3] RX Checksum Offload Engine supported
[ 1.660111@3] COE Type 2
[ 1.662731@3] TX Checksum insertion supported
[ 1.667193@3] Wake-Up On Lan supported
[ 1.671135@3] Enable RX Mitigation via HW Watchdog Timer
[ 1.684635@3] libphy: stmmac: probed
[ 1.684688@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[ 1.691108@3] PPP generic driver version 2.4.2
[ 1.694120@3] PPP BSD Compression module registered
[ 1.698623@3] PPP Deflate Compression module registered
[ 1.703884@3] PPP MPPE Compression module registered
[ 1.708838@3] NET: Registered protocol family 24
[ 1.714332@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.720235@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.727285@3] usbcore: registered new interface driver cdc_acm
[ 1.732480@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.740916@3] usbcore: registered new interface driver usbserial
[ 1.747574@3] mousedev: PS/2 mouse device common for all mice
[ 1.753069@3] usbcore: registered new interface driver xpad
[ 1.758444@3] i2c /dev entries driver
[ 1.763218@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.767445@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.778396@3] ff803000.serial: clock gate not found
[ 1.779948@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[ 1.787189@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[ 1.802097@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 1.804800@3] console [ttyS0] enabled
[ 1.812016@3] bootconsole [aml_uart0] disabled
[ 1.821693@2] ff804000.serial: clock gate not found
[ 1.825820@2] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[ 1.832926@2] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 1.843326@1] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[ 1.849423@1] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[ 1.859582@3] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[ 1.865881@3] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[ 1.876861@2] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[ 1.886120@2] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[ 1.892623@2] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[ 1.907607@2] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.911489@2] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.923835@2] aml_dma ff63e000.aml_dma: Aml dma
[ 1.927005@2] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[ 1.931949@2] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 1.938308@2] efusekeynum: 4
[ 1.940642@2] efusekeyname: mac offset: 0 size: 6
[ 1.947086@2] efusekeyname: mac_bt offset: 6 size: 6
[ 1.953505@2] efusekeyname: mac_wifi offset: 12 size: 6
[ 1.959906@2] efusekeyname: usid offset: 18 size: 16
[ 1.966741@1] efuse efuse: probe OK!
[ 1.972170@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 1.979424@0] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode
[ 1.984495@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 1.989731@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[ 2.036866@0] meson-mmc: meson_mmc_probe() : success!
[ 2.037149@0] amlogic mtd driver init
[ 2.041183@0] prase_get_dtb_nand_parameter:128,parse dts start
[ 2.045933@0] bl mode descrete
[ 2.048812@0] fip_copies 4
[ 2.051477@0] fip_size 0x200000
[ 2.054616@0] nand_clk_ctrl 0xffe07000
[ 2.058341@0] prase_get_dtb_nand_parameter:234,parse dts end
[ 2.064007@0] nand_clk_ctrl 0xffe07000
[ 2.067728@0] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[ 2.076538@0] plat->aml_nand_device ffffff800a005c10
[ 2.080639@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.086703@0] NAND device id: 2c da 90 95 6 0
[ 2.090764@0] NAND device: Manufacturer ID:
[ 2.094830@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.101873@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.107306@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.112854@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.119099@0] mtd->oobavail: 0x8
[ 2.122508@0] aml_nand_init 2119: plat-name:bootloader
[ 2.127418@0] Creating 1 MTD partitions on "bootloader":
[ 2.132722@0] 0x000000000000-0x000000200000 : "bootloader"
[ 2.141587@0] bootloader initialized ok
[ 2.141966@0] plat->aml_nand_device ffffff800a005c10
[ 2.146951@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.153086@0] NAND device id: 2c da 90 95 6 0
[ 2.157063@0] NAND device: Manufacturer ID:
[ 2.161139@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.168173@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.173614@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.179154@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.185406@0] mtd->oobavail: 0x8
[ 2.188861@0] aml_nand_init 2119: plat-name:nandnormal
[ 2.193765@0] bbt_start=20
[ 2.196381@0] env_start=24
[ 2.199095@0] key_start=32
[ 2.201774@0] dtb_start=40
[ 2.204440@0] ddr_start=44
[ 2.207169@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[ 2.213641@0] get_free_node 43: bitmap=0
[ 2.217114@0] get_free_node 55: bitmap=1
[ 2.221206@0] get_free_node 43: bitmap=1
[ 2.224913@0] get_free_node 55: bitmap=3
[ 2.229005@0] get_free_node 43: bitmap=3
[ 2.232695@0] get_free_node 55: bitmap=7
[ 2.236597@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[ 2.243284@0] nbbt free list:
[ 2.246231@0] blockN=21, ec=-1, dirty_flag=0
[ 2.250478@0] blockN=22, ec=-1, dirty_flag=0
[ 2.254724@0] blockN=23, ec=-1, dirty_flag=0
[ 2.258972@0] aml_nand_scan_rsv_info 1141: page_num=1
[ 2.264381@0] nbbt valid addr: 280000
[ 2.267641@0] aml_nand_bbt_check 1306 bbt is valid, reading.
[ 2.273272@0] aml_nand_read_rsv_info:423,read nbbt info at 280000
[ 2.279534@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[ 2.285962@0] get_free_node 43: bitmap=7
[ 2.289480@0] get_free_node 55: bitmap=f
[ 2.293571@0] get_free_node 43: bitmap=f
[ 2.297280@0] get_free_node 55: bitmap=1f
[ 2.301458@0] get_free_node 43: bitmap=1f
[ 2.305253@0] get_free_node 55: bitmap=3f
[ 2.309431@0] get_free_node 43: bitmap=3f
[ 2.313226@0] get_free_node 55: bitmap=7f
[ 2.317405@0] get_free_node 43: bitmap=7f
[ 2.321199@0] get_free_node 55: bitmap=ff
[ 2.325377@0] get_free_node 43: bitmap=ff
[ 2.329173@0] get_free_node 55: bitmap=1ff
[ 2.333438@0] get_free_node 43: bitmap=1ff
[ 2.337320@0] get_free_node 55: bitmap=3ff
[ 2.341393@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[ 2.348063@0] nenv free list:
[ 2.351011@0] blockN=25, ec=-1, dirty_flag=0
[ 2.355257@0] blockN=26, ec=-1, dirty_flag=0
[ 2.359504@0] blockN=27, ec=-1, dirty_flag=0
[ 2.363751@0] blockN=28, ec=-1, dirty_flag=0
[ 2.367997@0] blockN=29, ec=-1, dirty_flag=0
[ 2.372244@0] blockN=30, ec=-1, dirty_flag=0
[ 2.376491@0] blockN=31, ec=-1, dirty_flag=0
[ 2.380738@0] aml_nand_scan_rsv_info 1141: page_num=32
[ 2.398000@0] nenv valid addr: 310000
[ 2.398034@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[ 2.402392@0] get_free_node 43: bitmap=3ff
[ 2.406272@0] get_free_node 55: bitmap=7ff
[ 2.410537@0] get_free_node 43: bitmap=7ff
[ 2.414418@0] get_free_node 55: bitmap=fff
[ 2.418683@0] get_free_node 43: bitmap=fff
[ 2.422565@0] get_free_node 55: bitmap=1fff
[ 2.426917@0] get_free_node 43: bitmap=1fff
[ 2.430885@0] get_free_node 55: bitmap=3fff
[ 2.435236@0] get_free_node 43: bitmap=3fff
[ 2.439205@0] get_free_node 55: bitmap=7fff
[ 2.443556@0] get_free_node 43: bitmap=7fff
[ 2.447525@0] get_free_node 55: bitmap=ffff
[ 2.451876@0] get_free_node 43: bitmap=ffff
[ 2.455845@0] get_free_node 55: bitmap=1ffff
[ 2.460282@0] get_free_node 43: bitmap=1ffff
[ 2.464338@0] get_free_node 55: bitmap=3ffff
[ 2.468585@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.475255@0] nkey free list:
[ 2.478203@0] blockN=32, ec=-1, dirty_flag=0
[ 2.482450@0] blockN=33, ec=-1, dirty_flag=0
[ 2.486696@0] blockN=34, ec=-1, dirty_flag=0
[ 2.490942@0] blockN=35, ec=-1, dirty_flag=0
[ 2.495189@0] blockN=36, ec=-1, dirty_flag=0
[ 2.499436@0] blockN=37, ec=-1, dirty_flag=0
[ 2.503683@0] blockN=38, ec=-1, dirty_flag=0
[ 2.507929@0] blockN=39, ec=-1, dirty_flag=0
[ 2.512176@0] aml_nand_scan_rsv_info 1141: page_num=16
[ 2.517289@0] nkey valid addr: fffffffffffe0000
[ 2.521798@0] aml_nand_key_check 1251 NO key exist
[ 2.526564@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[ 2.533185@0] get_free_node 43: bitmap=3ffff
[ 2.537052@0] get_free_node 55: bitmap=7ffff
[ 2.541490@0] get_free_node 43: bitmap=7ffff
[ 2.545545@0] get_free_node 55: bitmap=fffff
[ 2.549983@0] get_free_node 43: bitmap=fffff
[ 2.554038@0] get_free_node 55: bitmap=1fffff
[ 2.558372@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[ 2.565042@0] ndtb free list:
[ 2.567973@0] blockN=41, ec=-1, dirty_flag=0
[ 2.572236@0] blockN=42, ec=-1, dirty_flag=0
[ 2.576483@0] blockN=43, ec=-1, dirty_flag=0
[ 2.580730@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.598036@0] ndtb valid addr: 500000
[ 2.598070@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[ 2.602510@0] get_free_node 43: bitmap=1fffff
[ 2.606654@0] get_free_node 55: bitmap=3fffff
[ 2.611178@0] get_free_node 43: bitmap=3fffff
[ 2.615320@0] get_free_node 55: bitmap=7fffff
[ 2.619653@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.626324@0] nddr free list:
[ 2.629271@0] blockN=44, ec=-1, dirty_flag=0
[ 2.633518@0] blockN=45, ec=-1, dirty_flag=0
[ 2.637765@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.642878@0] nddr valid addr: fffffffffffe0000
[ 2.647385@0] aml_nand_ddr_check 1281 NO ddr exist
[ 2.652155@0] tpl: off 8388608, size 8388608
[ 2.783826@0] Creating 6 MTD partitions on "nandnormal":
[ 2.783873@0] 0x000000800000-0x000001000000 : "tpl"
[ 2.795063@1] 0x000001000000-0x000001200000 : "misc"
[ 2.798192@2] 0x000001200000-0x000002200000 : "recovery"
[ 2.810242@2] 0x000002200000-0x000004200000 : "boot"
[ 2.829401@2] 0x000004200000-0x000004700000 : "config"
[ 2.834074@2] 0x000004700000-0x000010000000 : "nvdata"
[ 2.935098@0] nandnormal initialized ok
[ 2.935206@0] aml_ubootenv_init: register env chardev
[ 2.938937@0] aml_ubootenv_init: register env chardev OK
[ 2.943777@0] amlnf_dtb_init: register dtb cdev
[ 2.948751@0] amlnf_dtb_init: register dtd cdev OK
[ 2.952948@0] mtd_nand_probe 267 , err = 0
[ 2.958073@1] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[ 2.963525@1] input: aml_vkeypad as /devices/platform/rtc/input/input0
[ 2.970695@0] unifykey: storage in base: 0xffffffc005000000
[ 2.975132@0] unifykey: storage out base: 0xffffffc005040000
[ 2.980736@0] unifykey: storage block base: 0xffffffc005080000
[ 2.986536@0] unifykey: probe done!
[ 2.990733@0] unifykey: no efuse-version set, use default value: -1
[ 2.996262@0] unifykey: key unify config unifykey-num is 6
[ 3.001791@0] unifykey: key unify fact unifykey-num is 6
[ 3.006997@0] unifykey: unifykey_devno: f200000
[ 3.012184@0] unifykey: device unifykeys created ok
[ 3.016483@0] unifykey: aml_unifykeys_init done!
[ 3.021387@0] sysled: module init
[ 3.024884@0] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 3.029635@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 3.037067@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 3.045764@1] dmc_monitor_probe
[ 3.051602@1] defendkey defendkey: Reserved memory is not enough!
[ 3.052329@1] defendkey: probe of defendkey failed with error -22
[ 3.058760@1] GACT probability NOT on
[ 3.062087@1] Mirror/redirect action on
[ 3.065865@1] u32 classifier
[ 3.068680@1] Actions configured
[ 3.072258@1] Netfilter messages via NETLINK v0.30.
[ 3.077540@1] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 3.083734@1] ctnetlink v0.93: registering with nfnetlink.
[ 3.089610@1] xt_time: kernel timezone is -0000
[ 3.093328@1] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 3.099962@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.104642@1] arp_tables: arp_tables: (C) 2002 David S. Miller
[ 3.110134@1] Initializing XFRM netlink socket
[ 3.115657@1] NET: Registered protocol family 10
[ 3.121399@1] mip6: Mobile IPv6
[ 3.122205@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.128182@1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.136144@1] NET: Registered protocol family 17
[ 3.138458@1] NET: Registered protocol family 15
[ 3.143055@1] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.156196@1] l2tp_core: L2TP core driver, V2.0
[ 3.160592@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.165510@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 3.171261@1] l2tp_netlink: L2TP netlink interface
[ 3.176070@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 3.182143@1] l2tp_debugfs: L2TP debugfs support
[ 3.186654@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 3.193315@1] NET: Registered protocol family 35
[ 3.198232@1] Key type dns_resolver registered
[ 3.202794@1] Registered swp emulation handler
[ 3.206696@1] Registered cp15_barrier emulation handler
[ 3.211887@1] Registered setend emulation handler
[ 3.216630@1] disable EAS feature
[ 3.221612@1] registered taskstats version 1
[ 3.237799@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 3.744209@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.744296@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.752579@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[ 3.761021@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[ 3.768494@1] hub 1-0:1.0: USB hub found
[ 3.770979@1] hub 1-0:1.0: 1 port detected
[ 3.775569@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.780597@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.788491@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.797981@2] hub 2-0:1.0: USB hub found
[ 3.800549@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.807903@2] usb usb2: Unsupported the hub
[ 3.812636@2] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
[ 3.820742@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d173000)
[ 3.820820@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 3.828672@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[ 3.828684@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb27e00
[ 3.929280@2] dwc_otg: Core Release: 3.10a
[ 3.929334@2] dwc_otg: Setting default values for core params
[ 3.933530@2] dwc_otg: curmode: 0, host_only: 0
[ 3.938033@2] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[ 3.950538@2] dwc_otg: Using Buffer DMA mode
[ 3.950576@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 3.954484@2] dwc_otg: Working on port type = SLAVE
[ 3.959341@2] dwc_otg: Dedicated Tx FIFOs mode
[ 3.966279@2] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[ 3.973052@2] cpucore_cooling_register, max_cpu_core_num:4
[ 3.985266@0] gxbb_pm: enter meson_pm_probe!
[ 3.985324@0] no vddio3v3_en pin
[ 3.986975@0] pm-meson aml_pm: Can't get switch_clk81
[ 3.992074@0] gxbb_pm: meson_pm_probe done
[ 3.997041@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.003308@0] Freeing unused kernel memory: 3648K
[ 4.017619@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.269025@0] ubi0: attaching mtd5
[ 4.287552@0] ubi0: scanning is finished
[ 4.292113@3] ubi0: attached mtd5 (name "config", size 5 MiB)
[ 4.292242@3] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.299323@3] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.306209@3] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.313321@3] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[ 4.319381@3] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 4.326757@3] ubi0: max/mean erase counter: 10/5, WL threshold: 4096, image sequence number: 4272682163
[ 4.336106@3] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[ 4.345329@0] ubi0: background thread "ubi_bgt0d" started, PID 1076
[ 4.358538@1] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[ 4.375136@2] UBIFS (ubi0:0): recovery needed
[ 4.426251@0] UBIFS (ubi0:0): recovery completed
[ 4.426509@0] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[ 4.433261@0] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 4.443301@0] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 4.453522@0] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[ 4.460111@0] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID DF678CD6-72B3-440D-AD49-B5CACA89C146, small LPT model
[ 4.484804@0] ubi2: attaching mtd6
[ 5.158140@0] ubi2: scanning is finished
[ 5.165564@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[ 5.165868@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.172922@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.179845@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.186950@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[ 5.193186@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.200546@1] ubi2: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 3925779084
[ 5.209826@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[ 5.219200@3] ubi2: background thread "ubi_bgt2d" started, PID 1087
[ 5.232088@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091
[ 5.248767@0] UBIFS (ubi2:0): recovery needed
[ 5.296598@0] UBIFS (ubi2:0): recovery completed
[ 5.296903@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[ 5.303591@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.313643@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[ 5.324469@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[ 5.331233@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID D3E2E49A-3C02-4261-9EEF-3A2DAF328DBD, small LPT model
[ 5.551613@3] eth0: device MAC address 02:5a:b9:1d:92:fb
[ 5.633822@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 5.635120@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.886634@0] uart_trans: loading out-of-tree module taints kernel.
[ 5.889260@0] register uart_trans chrdev success.
[ 5.892442@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[ 5.900442@0] tty port open success [/dev/ttyS3]!
[ 5.904869@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[ 5.913386@0] init sucess for tty struct (246:3) [/dev/ttyS3]
[ 5.919339@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[ 5.926993@0] tty port open success [/dev/ttyS2]!
[ 5.931635@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[ 5.940103@0] init sucess for tty struct (246:2) [/dev/ttyS2]
[ 5.946228@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[ 5.953877@0] tty port open success [/dev/ttyS1]!
[ 5.958524@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[ 5.966946@0] init sucess for tty struct (246:1) [/dev/ttyS1]
[ 5.973018@0] create workqueue success!
[ 7.672988@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 7.676278@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.284909@1] uart trans dev open.
[ 32.285019@1] uart_buf virt addr = 0xffffffc00b1c0000
[ 32.287724@1] uart_buf phys addr = 0x0b1c0000
[ 32.292108@1] uart_buf pfn = 0x0000b1c0
[ 32.296926@1] uart trans stop send work timer.
[ 32.301098@1] uart trans set chain exist bits:0x7.
[ 32.305607@1] uart trans set work queue count 768.
[ 83.119658@3] uart set baud to: 4098
[ 83.119718@3] uart set baud to: 4098
[ 83.121230@3] uart set baud to: 4098
[ 96.236632@2] uart trans stop send work timer.
[ 98.947924@3] uart trans start send work timer.
[ 301.722926@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead.
===========================================Miner log===========================================
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 3
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 chain id = 0
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 chain id = 1
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 3
2015-01-01 00:00:21 skip loading levels for now
2023-06-16 22:30:25 load chain 0 eeprom data
2023-06-16 22:30:29 load chain 1 eeprom data
2023-06-16 22:30:32 load chain 2 eeprom data
2023-06-16 22:30:32 i2c_sim_init start
2023-06-16 22:30:32 init gpio477
2023-06-16 22:30:32 init gpio476
2023-06-16 22:30:32 i2c_sim_init end
2023-06-16 22:30:33 power open power_version = 0x76
2023-06-16 22:30:36 power is not Calibrated
2023-06-16 22:30:37 miner type: Antminer S19j Pro
2023-06-16 22:30:37 multi machine mode
2023-06-16 22:30:37 load machine BHB42631 conf
2023-06-16 22:30:37 machine : BHB42631
2023-06-16 22:30:37 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 abandon mix board!
2023-06-16 22:30:37 fan_eft : 0 fan_pwm : 100
2023-06-16 22:30:37 create thread get_nonce_and_register_thread
2023-06-16 22:30:37 fixed working voltage = 1380
2023-06-16 22:30:37 fixed frequency is 525
2023-06-16 22:30:37 Chain [0] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [0] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [1] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [1] BOM Version: 0x0010
2023-06-16 22:30:37 Chain [2] PCB Version: 0x0110
2023-06-16 22:30:37 Chain [2] BOM Version: 0x0010
2023-06-16 22:30:37 bad chain id = 3
2023-06-16 22:30:37 Fan check passed.
2023-06-16 22:30:37 uart_trans addr:0xf43df000.
2023-06-16 22:30:37 max sensor num = 4
2023-06-16 22:30:37 STATUS_INITED: soc init done!
2023-06-16 22:30:37 temperature_monitor_thread start...
2023-06-16 22:30:40 start to init...
2023-06-16 22:30:40 warning:power is not calibration.
2023-06-16 22:30:41 power type version: 0x0076
2023-06-16 22:30:43 disable power watchdog: 0x0000
2023-06-16 22:30:44 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-16 22:31:15 Slept 30 seconds, diff = 0.
2023-06-16 22:31:19 set_voltage_by_steps to 1500.
2023-06-16 22:31:28 start up min temp by 75a = 24
2023-06-16 22:31:31 Chain[0]: find 126 asic, times 0
2023-06-16 22:31:33 Chain[1]: find 126 asic, times 0
2023-06-16 22:31:35 Chain[2]: find 0 asic, times 0
2023-06-16 22:31:37 Chain[2]: find 0 asic, times 1
2023-06-16 22:31:38 Chain[2]: find 0 asic, times 2
2023-06-16 22:31:38 Chain 2 only find 0 asic, will power off hash board 2
2023-06-16 22:31:38 ERROR_SOC_INIT: soc init failed!
2023-06-16 22:31:38 stop_mining: soc init failed!
2023-06-16 22:31:38 uninit_temp_info
2023-06-16 22:31:38 do not read temp anymore...
2023-06-16 22:31:38 cancel thread
2023-06-16 22:31:38 ****power off hashboard****
2023-06-16 22:31:39 temp monitor thread exit
2023-06-16 22:31:44 Version num 65536
2023-06-16 22:31:44 Mask num 0x1fffe000
2023-06-16 22:31:44 opt_multi_version = 65536, interval timeout = 2945120
2023-06-16 22:31:44 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
Re: S19j Pro 104th chips state is "normal" but wont hash???
Its hashing fine with the 2 good boards that are in there.
I posted here in an attempt to get the 3rd working.
I suggest check the hashboard physically to look for possible burnt parts that cause this issue if you found one you might need to hire a technician to replace it or do DIY.I posted here in an attempt to get the 3rd working.
If you found nothing there are some basic things that you can do without a technician like cleaning the hashboard pins and if you have a soldering iron you can resolder all pins including the terminals on the busbar. Look at the image below to get my point.
https://i.ibb.co/tLWDsw8/20230613-074512.jpg
Yeah, I looked closely and could not find any issues.
I may need to ship out my machine to have it repaired by a professional.
I don't think its right that the warranty on these start the day it was built, instead of the day it was purchased. I've only owned it for 3 months.
Re: S19j Pro 104th chips state is "normal" but wont hash???
I attempted to install a single good board and same thing. I assume its not possible to run these machines on a single board.
Instead of installing the broken hashboard better remove it and try to run the two working hashboard it should be work but if not then you will need to install a custom firmware like Braiins OS as suggested above to be able to bypasss this issue.
If you don't know how to run the Braiins OS on the unit without SD card slot you can try OTG drive to boot Braiins OS check the link below.
- https://support.bitmain.com/hc/en-us/articles/4404919472281-S19j-S19j-Pro-control-board-program-recovery-SD-card-flashing-
Its hashing fine with the 2 good boards that are in there.
I posted here in an attempt to get the 3rd working.
Re: S19j Pro 104th chips state is "normal" but wont hash???
Very odd and there's nothing about it in the log. Let's try this, run the machine with only the bad hashboard plugged in. Then let's see the logs.
I pulled out the two good boards and now its telling me "No data yet! Data is currently unavailable".
I will try moving it back to the 1st slot. Maybe it cant boot correctly if there is only a single board in slot3.
Now we found the issue that the hashboard is broken it's not a software issue but a hardware issue.
You can replace it with a new one but if you still want to repair the hashboard and you have some repair tools there is a guide on how to repair this hashboard
Check this link below
- https://www.zeusbtc.com/articles/information/3530-antminer-s19j-pro-hash-board-repair-guide
I am not qualified to repair this board on my own.
Re: S19j Pro 104th chips state is "normal" but wont hash???
How do my logs look?
I can't make sense of it. lol
I can't make sense of it. lol
Honestly, I can't seems to find any errors in your logs.
Can you try to run only one hashboard disconnect the two hashboard and swap cables and let see if the first hashboard will hash?
Also, try to clean all terminals the cable, and the busbar it might have some corrosion/dust/rust so cleaning it might fix this issue.
Can you tell us what pool do you mine and maybe the pool where you mine is currently offline?
Ok. Should I attempt to move the hash board to a different slot?
Re: S19j Pro 104th chips state is "normal" but wont hash???
does not have the sd-card
This means one of three things, you have an amlogic "cousin wangs covid ARM sale" control board(thumb microUSB drive replaced microSD), a beagle bone control board(SD card slot is inside the control board housing), or it is one of the new "cousin wang's 2023 ARM CPU sale" control board I've started hearing rumors about(idek).The logs look fine also.
You can try these options.
1. Restore defaults in web interface and reload pool info.
2. Try configuring it with a remote tool like BTCtools.
3. Load/reload the latest firmware update from bitmain's website.
Number one worked for me last week when I had a similar seemingly fine log that simply didn't want to hadh but that machine was new to me, yours was running fine.
I did restore factory settings and it made no difference.
I also tried to update the firmware but it was already the latest version.
I don't own a windows PC so BTCtools is not an option to try.
Re: S19j Pro 104th chips state is "normal" but wont hash???
There is a possibility that the 1st hashboard is not connected properly.
What I would like you to try is to replug all cables of the 1st hashboard and then try again.
Or if my suggestion do not work would you mind to share the whole kernel logs? Post it here but make sure to put them all inside the insert code tag before you post. So that we can troubleshoot the issue.
What I would like you to try is to replug all cables of the 1st hashboard and then try again.
Or if my suggestion do not work would you mind to share the whole kernel logs? Post it here but make sure to put them all inside the insert code tag before you post. So that we can troubleshoot the issue.
How do my logs look?
I can't make sense of it. lol
Re: S19j Pro 104th chips state is "normal" but wont hash???
You could try burning a sdcard with braiins os see if it works.
Mine does not have the sd-card slot.
Re: S19j Pro 104th chips state is "normal" but wont hash???
Not sure but I see a line that says mixed board.
Did you get this direct from bitmain?
I know sometimes if you put two units into one machine it won’t run.
I wonder if your miner has boards from two miners.
Did you get this direct from bitmain?
I know sometimes if you put two units into one machine it won’t run.
I wonder if your miner has boards from two miners.
The box was sealed and purchased from an authorized Bitmain dealer.
It was running perfect for the past 3 months.
Re: S19j Pro 104th chips state is "normal" but wont hash???
⭐ Merited by philipma1957 (1)
Code:
===========================================Miner log===========================================
2023-06-11 12:59:02 Open miner sn file /config/sn error
2023-06-11 12:59:02 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-06-11 12:59:03 This is fix-freq version
2023-06-11 12:59:03 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-06-11 12:59:03 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-06-11 12:59:03 opt_multi_version = 1
2023-06-11 12:59:03 opt_bitmain_ab = 1
2023-06-11 12:59:03 mid_auto_gen = 1
2023-06-11 12:59:03 opt_bitmain_work_mode = 0
2023-06-11 12:59:03 port 439 already exported
2023-06-11 12:59:03 port 454 already exported
2023-06-11 12:59:03 port 440 already exported
2023-06-11 12:59:03 port 455 already exported
2023-06-11 12:59:03 port 441 already exported
2023-06-11 12:59:03 port 456 already exported
2023-06-11 12:59:03 port 438 already exported
2023-06-11 12:59:03 port 453 already exported
2023-06-11 12:59:03 port 446 already exported
2023-06-11 12:59:03 port 445 already exported
2023-06-11 12:59:03 Note: front fan is power on!
2023-06-11 12:59:03 Note: rear fan is power on!
2023-06-11 12:59:03 start the http log.
2023-06-11 12:59:03 httpListenThread start ret=0
2023-06-11 12:59:03 start listen on 6060 ...
2023-06-11 12:59:03 bad chain id = 3
2023-06-11 12:59:06 bad chain id = 3
2023-06-11 12:59:08 ==========================capability start==========================
2023-06-11 12:59:08 board num = 3
2023-06-11 12:59:08 board id = 0, chain num = 1
2023-06-11 12:59:08 chain id = 0
2023-06-11 12:59:08 board id = 1, chain num = 1
2023-06-11 12:59:08 chain id = 1
2023-06-11 12:59:08 board id = 2, chain num = 1
2023-06-11 12:59:08 chain id = 2
2023-06-11 12:59:08 ==========================capability end============================
2023-06-11 12:59:08 chain num = 3
2023-06-11 12:59:08 skip loading levels for now
2023-06-11 12:59:12 load chain 0 eeprom data
2023-06-11 12:59:15 load chain 1 eeprom data
2023-06-11 12:59:19 load chain 2 eeprom data
2023-06-11 12:59:19 i2c_sim_init start
2023-06-11 12:59:19 init gpio477
2023-06-11 12:59:19 init gpio476
2023-06-11 12:59:19 i2c_sim_init end
2023-06-11 12:59:20 power open power_version = 0x76
2023-06-11 12:59:23 power is not Calibrated
2023-06-11 12:59:24 miner type: Antminer S19j Pro
2023-06-11 12:59:24 multi machine mode
2023-06-11 12:59:24 load machine BHB42631 conf
2023-06-11 12:59:24 machine : BHB42631
2023-06-11 12:59:24 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-11 12:59:24 abandon mix board!
2023-06-11 12:59:24 abandon mix board!
2023-06-11 12:59:24 fan_eft : 0 fan_pwm : 100
2023-06-11 12:59:24 create thread get_nonce_and_register_thread
2023-06-11 12:59:24 fixed working voltage = 1380
2023-06-11 12:59:24 fixed frequency is 525
2023-06-11 12:59:24 Chain [0] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [0] BOM Version: 0x0010
2023-06-11 12:59:24 Chain [1] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [1] BOM Version: 0x0010
2023-06-11 12:59:24 Chain [2] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [2] BOM Version: 0x0010
2023-06-11 12:59:24 bad chain id = 3
2023-06-11 12:59:24 Fan check passed.
2023-06-11 12:59:24 uart_trans addr:0xf6d72000.
2023-06-11 12:59:24 max sensor num = 4
2023-06-11 12:59:24 STATUS_INITED: soc init done!
2023-06-11 12:59:24 temperature_monitor_thread start...
2023-06-11 12:59:27 start to init...
2023-06-11 12:59:27 warning:power is not calibration.
2023-06-11 12:59:28 power type version: 0x0076
2023-06-11 12:59:30 disable power watchdog: 0x0000
2023-06-11 12:59:31 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-11 13:02:00 Slept 148 seconds, diff = 3.
2023-06-11 13:02:03 set_voltage_by_steps to 1500.
2023-06-11 13:02:13 start up min temp by 75a = 18
2023-06-11 13:02:16 Chain[0]: find 126 asic, times 0
2023-06-11 13:02:18 Chain[1]: find 126 asic, times 0
2023-06-11 13:02:20 Chain[2]: find 126 asic, times 0
2023-06-11 13:02:25 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:02:29 Bring up temperature is 19
2023-06-11 13:02:29 set UART baud to 3000000
2023-06-11 13:02:29 create thread check_miner_status_thread
2023-06-11 13:02:29 create thread check_system_work_thread
2023-06-11 13:02:29 set_voltage_by_steps to 1450.
2023-06-11 13:02:32 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:02:32 start do_core_reset
2023-06-11 13:02:51 end do_core_reset
2023-06-11 13:02:51 chain[0] min = 525 max =525
2023-06-11 13:02:51 chain[1] min = 525 max =525
2023-06-11 13:02:51 chain[2] min = 525 max =525
2023-06-11 13:02:51 1.inc all chain freq to 525
2023-06-11 13:02:51 fixed step freq_start = 50, freq_end = 525, freq_step = 6.25
2023-06-11 13:02:51 chain = 0 set freq to 56.25
2023-06-11 13:02:51 chain = 1 set freq to 56.25
2023-06-11 13:02:51 chain = 2 set freq to 56.25
2023-06-11 13:02:51 chain = 0 set freq to 62.50
2023-06-11 13:02:51 chain = 1 set freq to 62.50
2023-06-11 13:02:51 chain = 2 set freq to 62.50
2023-06-11 13:02:52 chain = 0 set freq to 68.75
2023-06-11 13:02:52 chain = 1 set freq to 68.75
2023-06-11 13:02:52 chain = 2 set freq to 68.75
2023-06-11 13:02:52 chain = 0 set freq to 75.00
2023-06-11 13:02:52 chain = 1 set freq to 75.00
2023-06-11 13:02:52 chain = 2 set freq to 75.00
2023-06-11 13:02:52 chain = 0 set freq to 81.25
2023-06-11 13:02:52 chain = 1 set freq to 81.25
2023-06-11 13:02:52 chain = 2 set freq to 81.25
2023-06-11 13:02:53 chain = 0 set freq to 87.50
2023-06-11 13:02:53 chain = 1 set freq to 87.50
2023-06-11 13:02:53 chain = 2 set freq to 87.50
2023-06-11 13:02:53 chain = 0 set freq to 93.75
2023-06-11 13:02:53 chain = 1 set freq to 93.75
2023-06-11 13:02:53 chain = 2 set freq to 93.75
2023-06-11 13:02:53 chain = 0 set freq to 100.00
2023-06-11 13:02:53 chain = 1 set freq to 100.00
2023-06-11 13:02:53 chain = 2 set freq to 100.00
2023-06-11 13:02:53 chain = 0 set freq to 106.25
2023-06-11 13:02:53 chain = 1 set freq to 106.25
2023-06-11 13:02:53 chain = 2 set freq to 106.25
2023-06-11 13:02:54 chain = 0 set freq to 112.50
2023-06-11 13:02:54 chain = 1 set freq to 112.50
2023-06-11 13:02:54 chain = 2 set freq to 112.50
2023-06-11 13:02:54 chain = 0 set freq to 118.75
2023-06-11 13:02:54 chain = 1 set freq to 118.75
2023-06-11 13:02:54 chain = 2 set freq to 118.75
2023-06-11 13:02:54 chain = 0 set freq to 125.00
2023-06-11 13:02:54 chain = 1 set freq to 125.00
2023-06-11 13:02:54 chain = 2 set freq to 125.00
2023-06-11 13:02:55 chain = 0 set freq to 131.25
2023-06-11 13:02:55 chain = 1 set freq to 131.25
2023-06-11 13:02:55 chain = 2 set freq to 131.25
2023-06-11 13:02:55 chain = 0 set freq to 137.50
2023-06-11 13:02:55 chain = 1 set freq to 137.50
2023-06-11 13:02:55 chain = 2 set freq to 137.50
2023-06-11 13:02:55 chain = 0 set freq to 143.75
2023-06-11 13:02:55 chain = 1 set freq to 143.75
2023-06-11 13:02:55 chain = 2 set freq to 143.75
2023-06-11 13:02:56 chain = 0 set freq to 150.00
2023-06-11 13:02:56 chain = 1 set freq to 150.00
2023-06-11 13:02:56 chain = 2 set freq to 150.00
2023-06-11 13:02:56 chain = 0 set freq to 156.25
2023-06-11 13:02:56 chain = 1 set freq to 156.25
2023-06-11 13:02:56 chain = 2 set freq to 156.25
2023-06-11 13:02:56 chain = 0 set freq to 162.50
2023-06-11 13:02:56 chain = 1 set freq to 162.50
2023-06-11 13:02:56 chain = 2 set freq to 162.50
2023-06-11 13:02:56 chain = 0 set freq to 168.75
2023-06-11 13:02:56 chain = 1 set freq to 168.75
2023-06-11 13:02:56 chain = 2 set freq to 168.75
2023-06-11 13:02:57 chain = 0 set freq to 175.00
2023-06-11 13:02:57 chain = 1 set freq to 175.00
2023-06-11 13:02:57 chain = 2 set freq to 175.00
2023-06-11 13:02:57 chain = 0 set freq to 181.25
2023-06-11 13:02:57 chain = 1 set freq to 181.25
2023-06-11 13:02:57 chain = 2 set freq to 181.25
2023-06-11 13:02:57 chain = 0 set freq to 187.50
2023-06-11 13:02:57 chain = 1 set freq to 187.50
2023-06-11 13:02:57 chain = 2 set freq to 187.50
2023-06-11 13:02:58 chain = 0 set freq to 193.75
2023-06-11 13:02:58 chain = 1 set freq to 193.75
2023-06-11 13:02:58 chain = 2 set freq to 193.75
2023-06-11 13:02:58 chain = 0 set freq to 200.00
2023-06-11 13:02:58 chain = 1 set freq to 200.00
2023-06-11 13:02:58 chain = 2 set freq to 200.00
2023-06-11 13:02:58 chain = 0 set freq to 206.25
2023-06-11 13:02:58 chain = 1 set freq to 206.25
2023-06-11 13:02:58 chain = 2 set freq to 206.25
2023-06-11 13:02:59 chain = 0 set freq to 212.50
2023-06-11 13:02:59 chain = 1 set freq to 212.50
2023-06-11 13:02:59 chain = 2 set freq to 212.50
2023-06-11 13:02:59 chain = 0 set freq to 218.75
2023-06-11 13:02:59 chain = 1 set freq to 218.75
2023-06-11 13:02:59 chain = 2 set freq to 218.75
2023-06-11 13:02:59 chain = 0 set freq to 225.00
2023-06-11 13:02:59 chain = 1 set freq to 225.00
2023-06-11 13:02:59 chain = 2 set freq to 225.00
2023-06-11 13:02:59 chain = 0 set freq to 231.25
2023-06-11 13:02:59 chain = 1 set freq to 231.25
2023-06-11 13:02:59 chain = 2 set freq to 231.25
2023-06-11 13:03:00 chain = 0 set freq to 237.50
2023-06-11 13:03:00 chain = 1 set freq to 237.50
2023-06-11 13:03:00 chain = 2 set freq to 237.50
2023-06-11 13:03:00 chain = 0 set freq to 243.75
2023-06-11 13:03:00 chain = 1 set freq to 243.75
2023-06-11 13:03:00 chain = 2 set freq to 243.75
2023-06-11 13:03:00 chain = 0 set freq to 250.00
2023-06-11 13:03:00 chain = 1 set freq to 250.00
2023-06-11 13:03:00 chain = 2 set freq to 250.00
2023-06-11 13:03:01 chain = 0 set freq to 256.25
2023-06-11 13:03:01 chain = 1 set freq to 256.25
2023-06-11 13:03:01 chain = 2 set freq to 256.25
2023-06-11 13:03:01 chain = 0 set freq to 262.50
2023-06-11 13:03:01 chain = 1 set freq to 262.50
2023-06-11 13:03:01 chain = 2 set freq to 262.50
2023-06-11 13:03:01 chain = 0 set freq to 268.75
2023-06-11 13:03:01 chain = 1 set freq to 268.75
2023-06-11 13:03:01 chain = 2 set freq to 268.75
2023-06-11 13:03:02 chain = 0 set freq to 275.00
2023-06-11 13:03:02 chain = 1 set freq to 275.00
2023-06-11 13:03:02 chain = 2 set freq to 275.00
2023-06-11 13:03:02 chain = 0 set freq to 281.25
2023-06-11 13:03:02 chain = 1 set freq to 281.25
2023-06-11 13:03:02 chain = 2 set freq to 281.25
2023-06-11 13:03:02 chain = 0 set freq to 287.50
2023-06-11 13:03:02 chain = 1 set freq to 287.50
2023-06-11 13:03:02 chain = 2 set freq to 287.50
2023-06-11 13:03:02 chain = 0 set freq to 293.75
2023-06-11 13:03:02 chain = 1 set freq to 293.75
2023-06-11 13:03:02 chain = 2 set freq to 293.75
2023-06-11 13:03:03 chain = 0 set freq to 300.00
2023-06-11 13:03:03 chain = 1 set freq to 300.00
2023-06-11 13:03:03 chain = 2 set freq to 300.00
2023-06-11 13:03:03 chain = 0 set freq to 306.25
2023-06-11 13:03:03 chain = 1 set freq to 306.25
2023-06-11 13:03:03 chain = 2 set freq to 306.25
2023-06-11 13:03:03 chain = 0 set freq to 312.50
2023-06-11 13:03:03 chain = 1 set freq to 312.50
2023-06-11 13:03:03 chain = 2 set freq to 312.50
2023-06-11 13:03:04 chain = 0 set freq to 318.75
2023-06-11 13:03:04 chain = 1 set freq to 318.75
2023-06-11 13:03:04 chain = 2 set freq to 318.75
2023-06-11 13:03:04 chain = 0 set freq to 325.00
2023-06-11 13:03:04 chain = 1 set freq to 325.00
2023-06-11 13:03:04 chain = 2 set freq to 325.00
2023-06-11 13:03:04 chain = 0 set freq to 331.25
2023-06-11 13:03:04 chain = 1 set freq to 331.25
2023-06-11 13:03:04 chain = 2 set freq to 331.25
2023-06-11 13:03:05 chain = 0 set freq to 337.50
2023-06-11 13:03:05 chain = 1 set freq to 337.50
2023-06-11 13:03:05 chain = 2 set freq to 337.50
2023-06-11 13:03:05 chain = 0 set freq to 343.75
2023-06-11 13:03:05 chain = 1 set freq to 343.75
2023-06-11 13:03:05 chain = 2 set freq to 343.75
2023-06-11 13:03:05 chain = 0 set freq to 350.00
2023-06-11 13:03:05 chain = 1 set freq to 350.00
2023-06-11 13:03:05 chain = 2 set freq to 350.00
2023-06-11 13:03:06 chain = 0 set freq to 356.25
2023-06-11 13:03:06 chain = 1 set freq to 356.25
2023-06-11 13:03:06 chain = 2 set freq to 356.25
2023-06-11 13:03:06 chain = 0 set freq to 362.50
2023-06-11 13:03:06 chain = 1 set freq to 362.50
2023-06-11 13:03:06 chain = 2 set freq to 362.50
2023-06-11 13:03:06 chain = 0 set freq to 368.75
2023-06-11 13:03:06 chain = 1 set freq to 368.75
2023-06-11 13:03:06 chain = 2 set freq to 368.75
2023-06-11 13:03:06 chain = 0 set freq to 375.00
2023-06-11 13:03:06 chain = 1 set freq to 375.00
2023-06-11 13:03:06 chain = 2 set freq to 375.00
2023-06-11 13:03:07 chain = 0 set freq to 381.25
2023-06-11 13:03:07 chain = 1 set freq to 381.25
2023-06-11 13:03:07 chain = 2 set freq to 381.25
2023-06-11 13:03:07 chain = 0 set freq to 387.50
2023-06-11 13:03:07 chain = 1 set freq to 387.50
2023-06-11 13:03:07 chain = 2 set freq to 387.50
2023-06-11 13:03:07 chain = 0 set freq to 393.75
2023-06-11 13:03:07 chain = 1 set freq to 393.75
2023-06-11 13:03:07 chain = 2 set freq to 393.75
2023-06-11 13:03:08 chain = 0 set freq to 400.00
2023-06-11 13:03:08 chain = 1 set freq to 400.00
2023-06-11 13:03:08 chain = 2 set freq to 400.00
2023-06-11 13:03:08 chain = 0 set freq to 406.25
2023-06-11 13:03:08 chain = 1 set freq to 406.25
2023-06-11 13:03:08 chain = 2 set freq to 406.25
2023-06-11 13:03:08 chain = 0 set freq to 412.50
2023-06-11 13:03:08 chain = 1 set freq to 412.50
2023-06-11 13:03:08 chain = 2 set freq to 412.50
2023-06-11 13:03:09 chain = 0 set freq to 418.75
2023-06-11 13:03:09 chain = 1 set freq to 418.75
2023-06-11 13:03:09 chain = 2 set freq to 418.75
2023-06-11 13:03:09 chain = 0 set freq to 425.00
2023-06-11 13:03:09 chain = 1 set freq to 425.00
2023-06-11 13:03:09 chain = 2 set freq to 425.00
2023-06-11 13:03:09 chain = 0 set freq to 431.25
2023-06-11 13:03:09 chain = 1 set freq to 431.25
2023-06-11 13:03:09 chain = 2 set freq to 431.25
2023-06-11 13:03:09 chain = 0 set freq to 437.50
2023-06-11 13:03:09 chain = 1 set freq to 437.50
2023-06-11 13:03:09 chain = 2 set freq to 437.50
2023-06-11 13:03:10 chain = 0 set freq to 443.75
2023-06-11 13:03:10 chain = 1 set freq to 443.75
2023-06-11 13:03:10 chain = 2 set freq to 443.75
2023-06-11 13:03:10 chain = 0 set freq to 450.00
2023-06-11 13:03:10 chain = 1 set freq to 450.00
2023-06-11 13:03:10 chain = 2 set freq to 450.00
2023-06-11 13:03:10 chain = 0 set freq to 456.25
2023-06-11 13:03:10 chain = 1 set freq to 456.25
2023-06-11 13:03:10 chain = 2 set freq to 456.25
2023-06-11 13:03:11 chain = 0 set freq to 462.50
2023-06-11 13:03:11 chain = 1 set freq to 462.50
2023-06-11 13:03:11 chain = 2 set freq to 462.50
2023-06-11 13:03:11 chain = 0 set freq to 468.75
2023-06-11 13:03:11 chain = 1 set freq to 468.75
2023-06-11 13:03:11 chain = 2 set freq to 468.75
2023-06-11 13:03:11 chain = 0 set freq to 475.00
2023-06-11 13:03:11 chain = 1 set freq to 475.00
2023-06-11 13:03:11 chain = 2 set freq to 475.00
2023-06-11 13:03:12 chain = 0 set freq to 481.25
2023-06-11 13:03:12 chain = 1 set freq to 481.25
2023-06-11 13:03:12 chain = 2 set freq to 481.25
2023-06-11 13:03:12 chain = 0 set freq to 487.50
2023-06-11 13:03:12 chain = 1 set freq to 487.50
2023-06-11 13:03:12 chain = 2 set freq to 487.50
2023-06-11 13:03:12 chain = 0 set freq to 493.75
2023-06-11 13:03:12 chain = 1 set freq to 493.75
2023-06-11 13:03:12 chain = 2 set freq to 493.75
2023-06-11 13:03:12 chain = 0 set freq to 500.00
2023-06-11 13:03:12 chain = 1 set freq to 500.00
2023-06-11 13:03:12 chain = 2 set freq to 500.00
2023-06-11 13:03:13 chain = 0 set freq to 506.25
2023-06-11 13:03:13 chain = 1 set freq to 506.25
2023-06-11 13:03:13 chain = 2 set freq to 506.25
2023-06-11 13:03:13 chain = 0 set freq to 512.50
2023-06-11 13:03:13 chain = 1 set freq to 512.50
2023-06-11 13:03:13 chain = 2 set freq to 512.50
2023-06-11 13:03:13 chain = 0 set freq to 518.75
2023-06-11 13:03:13 chain = 1 set freq to 518.75
2023-06-11 13:03:13 chain = 2 set freq to 518.75
2023-06-11 13:03:14 chain = 0 set freq to 525.00
2023-06-11 13:03:14 chain = 1 set freq to 525.00
2023-06-11 13:03:14 chain = 2 set freq to 525.00
2023-06-11 13:03:14 enter mixed freq cfg
2023-06-11 13:03:14 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:03:14 start do_core_reset
2023-06-11 13:03:33 end do_core_reset
2023-06-11 13:03:43 set_voltage_by_steps to 1383.
2023-06-11 13:03:45 create thread pic_heart_beat_thread
2023-06-11 13:03:45 Init done!
2023-06-11 13:03:45 STATUS_OKAY
2023-06-11 13:03:45 start the cached job
2023-06-11 13:03:45 Version num 65536
2023-06-11 13:03:45 Mask num 0x1fffe000
2023-06-11 13:03:45 opt_multi_version = 65536, interval timeout = 2945120
2023-06-11 13:03:45 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-06-11 13:03:45 set_start_time_point total_tv_start_sys=293 total_tv_end_sys=294
2023-06-11 13:03:46 enable power watchdog: 0x0001
2023-06-11 13:04:22 set_voltage_by_steps to 1393.
2023-06-11 13:04:44 set_voltage_by_steps to 1403.
2023-06-11 13:32:31 avg rate is lower than ideal rate, 68024.48 in 28 mins
2023-06-11 13:32:31 30m avg rate is 68024.48 in 28 mins
2023-06-11 13:48:56 ****power off hashboard****
2023-06-11 13:49:20 Open miner sn file /config/sn error
2023-06-11 13:49:20 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-06-11 13:49:21 This is fix-freq version
2023-06-11 13:49:21 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-06-11 13:49:21 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-06-11 13:49:21 opt_multi_version = 1
2023-06-11 13:49:21 opt_bitmain_ab = 1
2023-06-11 13:49:21 mid_auto_gen = 1
2023-06-11 13:49:21 opt_bitmain_work_mode = 0
2023-06-11 13:49:21 port 439 already exported
2023-06-11 13:49:21 port 454 already exported
2023-06-11 13:49:21 port 440 already exported
2023-06-11 13:49:21 port 455 already exported
2023-06-11 13:49:21 port 441 already exported
2023-06-11 13:49:21 port 456 already exported
2023-06-11 13:49:21 port 438 already exported
2023-06-11 13:49:21 port 453 already exported
2023-06-11 13:49:21 port 446 already exported
2023-06-11 13:49:21 port 445 already exported
2023-06-11 13:49:21 Note: front fan is power on!
2023-06-11 13:49:21 Note: rear fan is power on!
2023-06-11 13:49:21 start the http log.
2023-06-11 13:49:21 httpListenThread start ret=0
2023-06-11 13:49:21 start listen on 6060 ...
2023-06-11 13:49:21 bad chain id = 3
2023-06-11 13:49:24 bad chain id = 3
2023-06-11 13:49:26 ==========================capability start==========================
2023-06-11 13:49:26 board num = 3
2023-06-11 13:49:26 board id = 0, chain num = 1
2023-06-11 13:49:26 chain id = 0
2023-06-11 13:49:26 board id = 1, chain num = 1
2023-06-11 13:49:26 chain id = 1
2023-06-11 13:49:26 board id = 2, chain num = 1
2023-06-11 13:49:26 chain id = 2
2023-06-11 13:49:26 ==========================capability end============================
2023-06-11 13:49:26 chain num = 3
2023-06-11 13:49:26 skip loading levels for now
2023-06-11 13:49:30 load chain 0 eeprom data
2023-06-11 13:49:33 load chain 1 eeprom data
2023-06-11 13:49:36 load chain 2 eeprom data
2023-06-11 13:49:36 i2c_sim_init start
2023-06-11 13:49:36 init gpio477
2023-06-11 13:49:36 init gpio476
2023-06-11 13:49:36 i2c_sim_init end
2023-06-11 13:49:38 power open power_version = 0x76
2023-06-11 13:49:40 power is not Calibrated
2023-06-11 13:49:42 miner type: Antminer S19j Pro
2023-06-11 13:49:42 multi machine mode
2023-06-11 13:49:42 load machine BHB42631 conf
2023-06-11 13:49:42 machine : BHB42631
2023-06-11 13:49:42 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-11 13:49:42 abandon mix board!
2023-06-11 13:49:42 abandon mix board!
2023-06-11 13:49:42 fan_eft : 0 fan_pwm : 100
2023-06-11 13:49:42 create thread get_nonce_and_register_thread
2023-06-11 13:49:42 fixed working voltage = 1380
2023-06-11 13:49:42 fixed frequency is 525
2023-06-11 13:49:42 Chain [0] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [0] BOM Version: 0x0010
2023-06-11 13:49:42 Chain [1] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [1] BOM Version: 0x0010
2023-06-11 13:49:42 Chain [2] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [2] BOM Version: 0x0010
2023-06-11 13:49:42 bad chain id = 3
2023-06-11 13:49:42 Fan check passed.
2023-06-11 13:49:42 uart_trans addr:0xf71d1000.
2023-06-11 13:49:42 max sensor num = 4
2023-06-11 13:49:42 STATUS_INITED: soc init done!
2023-06-11 13:49:42 temperature_monitor_thread start...
2023-06-11 13:49:45 start to init...
2023-06-11 13:49:45 warning:power is not calibration.
2023-06-11 13:49:46 power type version: 0x0076
2023-06-11 13:49:47 disable power watchdog: 0x0000
2023-06-11 13:49:48 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-11 13:51:57 Slept 128 seconds, diff = 3.
2023-06-11 13:52:01 set_voltage_by_steps to 1500.
2023-06-11 13:52:11 start up min temp by 75a = 19
2023-06-11 13:52:14 Chain[0]: find 126 asic, times 0
2023-06-11 13:52:16 Chain[1]: find 126 asic, times 0
2023-06-11 13:52:18 Chain[2]: find 126 asic, times 0
2023-06-11 13:52:23 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:52:27 Bring up temperature is 20
2023-06-11 13:52:27 set UART baud to 3000000
2023-06-11 13:52:27 create thread check_miner_status_thread
2023-06-11 13:52:27 create thread check_system_work_thread
2023-06-11 13:52:27 set_voltage_by_steps to 1450.
2023-06-11 13:52:30 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:52:30 start do_core_reset
2023-06-11 13:52:49 end do_core_reset
2023-06-11 13:52:49 chain[0] min = 525 max =525
2023-06-11 13:52:49 chain[1] min = 525 max =525
2023-06-11 13:52:49 chain[2] min = 525 max =525
2023-06-11 13:52:49 1.inc all chain freq to 525
2023-06-11 13:52:49 fixed step freq_start = 50, freq_end = 525, freq_step = 6.25
2023-06-11 13:52:49 chain = 0 set freq to 56.25
2023-06-11 13:52:49 chain = 1 set freq to 56.25
2023-06-11 13:52:49 chain = 2 set freq to 56.25
2023-06-11 13:52:49 chain = 0 set freq to 62.50
2023-06-11 13:52:49 chain = 1 set freq to 62.50
2023-06-11 13:52:49 chain = 2 set freq to 62.50
2023-06-11 13:52:49 chain = 0 set freq to 68.75
2023-06-11 13:52:49 chain = 1 set freq to 68.75
2023-06-11 13:52:49 chain = 2 set freq to 68.75
2023-06-11 13:52:50 chain = 0 set freq to 75.00
2023-06-11 13:52:50 chain = 1 set freq to 75.00
2023-06-11 13:52:50 chain = 2 set freq to 75.00
2023-06-11 13:52:50 chain = 0 set freq to 81.25
2023-06-11 13:52:50 chain = 1 set freq to 81.25
2023-06-11 13:52:50 chain = 2 set freq to 81.25
2023-06-11 13:52:50 chain = 0 set freq to 87.50
2023-06-11 13:52:50 chain = 1 set freq to 87.50
2023-06-11 13:52:50 chain = 2 set freq to 87.50
2023-06-11 13:52:51 chain = 0 set freq to 93.75
2023-06-11 13:52:51 chain = 1 set freq to 93.75
2023-06-11 13:52:51 chain = 2 set freq to 93.75
2023-06-11 13:52:51 chain = 0 set freq to 100.00
2023-06-11 13:52:51 chain = 1 set freq to 100.00
2023-06-11 13:52:51 chain = 2 set freq to 100.00
2023-06-11 13:52:51 chain = 0 set freq to 106.25
2023-06-11 13:52:51 chain = 1 set freq to 106.25
2023-06-11 13:52:51 chain = 2 set freq to 106.25
2023-06-11 13:52:51 chain = 0 set freq to 112.50
2023-06-11 13:52:51 chain = 1 set freq to 112.50
2023-06-11 13:52:51 chain = 2 set freq to 112.50
2023-06-11 13:52:52 chain = 0 set freq to 118.75
2023-06-11 13:52:52 chain = 1 set freq to 118.75
2023-06-11 13:52:52 chain = 2 set freq to 118.75
2023-06-11 13:52:52 chain = 0 set freq to 125.00
2023-06-11 13:52:52 chain = 1 set freq to 125.00
2023-06-11 13:52:52 chain = 2 set freq to 125.00
2023-06-11 13:52:52 chain = 0 set freq to 131.25
2023-06-11 13:52:52 chain = 1 set freq to 131.25
2023-06-11 13:52:52 chain = 2 set freq to 131.25
2023-06-11 13:52:53 chain = 0 set freq to 137.50
2023-06-11 13:52:53 chain = 1 set freq to 137.50
2023-06-11 13:52:53 chain = 2 set freq to 137.50
2023-06-11 13:52:53 chain = 0 set freq to 143.75
2023-06-11 13:52:53 chain = 1 set freq to 143.75
2023-06-11 13:52:53 chain = 2 set freq to 143.75
2023-06-11 13:52:53 chain = 0 set freq to 150.00
2023-06-11 13:52:53 chain = 1 set freq to 150.00
2023-06-11 13:52:53 chain = 2 set freq to 150.00
2023-06-11 13:52:54 chain = 0 set freq to 156.25
2023-06-11 13:52:54 chain = 1 set freq to 156.25
2023-06-11 13:52:54 chain = 2 set freq to 156.25
2023-06-11 13:52:54 chain = 0 set freq to 162.50
2023-06-11 13:52:54 chain = 1 set freq to 162.50
2023-06-11 13:52:54 chain = 2 set freq to 162.50
2023-06-11 13:52:54 chain = 0 set freq to 168.75
2023-06-11 13:52:54 chain = 1 set freq to 168.75
2023-06-11 13:52:54 chain = 2 set freq to 168.75
2023-06-11 13:52:54 chain = 0 set freq to 175.00
2023-06-11 13:52:54 chain = 1 set freq to 175.00
2023-06-11 13:52:54 chain = 2 set freq to 175.00
2023-06-11 13:52:55 chain = 0 set freq to 181.25
2023-06-11 13:52:55 chain = 1 set freq to 181.25
2023-06-11 13:52:55 chain = 2 set freq to 181.25
2023-06-11 13:52:55 chain = 0 set freq to 187.50
2023-06-11 13:52:55 chain = 1 set freq to 187.50
2023-06-11 13:52:55 chain = 2 set freq to 187.50
2023-06-11 13:52:55 chain = 0 set freq to 193.75
2023-06-11 13:52:55 chain = 1 set freq to 193.75
2023-06-11 13:52:55 chain = 2 set freq to 193.75
2023-06-11 13:52:56 chain = 0 set freq to 200.00
2023-06-11 13:52:56 chain = 1 set freq to 200.00
2023-06-11 13:52:56 chain = 2 set freq to 200.00
2023-06-11 13:52:56 chain = 0 set freq to 206.25
2023-06-11 13:52:56 chain = 1 set freq to 206.25
2023-06-11 13:52:56 chain = 2 set freq to 206.25
2023-06-11 13:52:56 chain = 0 set freq to 212.50
2023-06-11 13:52:56 chain = 1 set freq to 212.50
2023-06-11 13:52:56 chain = 2 set freq to 212.50
2023-06-11 13:52:57 chain = 0 set freq to 218.75
2023-06-11 13:52:57 chain = 1 set freq to 218.75
2023-06-11 13:52:57 chain = 2 set freq to 218.75
2023-06-11 13:52:57 chain = 0 set freq to 225.00
2023-06-11 13:52:57 chain = 1 set freq to 225.00
2023-06-11 13:52:57 chain = 2 set freq to 225.00
2023-06-11 13:52:57 chain = 0 set freq to 231.25
2023-06-11 13:52:57 chain = 1 set freq to 231.25
2023-06-11 13:52:57 chain = 2 set freq to 231.25
2023-06-11 13:52:57 chain = 0 set freq to 237.50
2023-06-11 13:52:57 chain = 1 set freq to 237.50
2023-06-11 13:52:57 chain = 2 set freq to 237.50
2023-06-11 13:52:58 chain = 0 set freq to 243.75
2023-06-11 13:52:58 chain = 1 set freq to 243.75
2023-06-11 13:52:58 chain = 2 set freq to 243.75
2023-06-11 13:52:58 chain = 0 set freq to 250.00
2023-06-11 13:52:58 chain = 1 set freq to 250.00
2023-06-11 13:52:58 chain = 2 set freq to 250.00
2023-06-11 13:52:58 chain = 0 set freq to 256.25
2023-06-11 13:52:58 chain = 1 set freq to 256.25
2023-06-11 13:52:58 chain = 2 set freq to 256.25
2023-06-11 13:52:59 chain = 0 set freq to 262.50
2023-06-11 13:52:59 chain = 1 set freq to 262.50
2023-06-11 13:52:59 chain = 2 set freq to 262.50
2023-06-11 13:52:59 chain = 0 set freq to 268.75
2023-06-11 13:52:59 chain = 1 set freq to 268.75
2023-06-11 13:52:59 chain = 2 set freq to 268.75
2023-06-11 13:52:59 chain = 0 set freq to 275.00
2023-06-11 13:52:59 chain = 1 set freq to 275.00
2023-06-11 13:52:59 chain = 2 set freq to 275.00
2023-06-11 13:53:00 chain = 0 set freq to 281.25
2023-06-11 13:53:00 chain = 1 set freq to 281.25
2023-06-11 13:53:00 chain = 2 set freq to 281.25
2023-06-11 13:53:00 chain = 0 set freq to 287.50
2023-06-11 13:53:00 chain = 1 set freq to 287.50
2023-06-11 13:53:00 chain = 2 set freq to 287.50
2023-06-11 13:53:00 chain = 0 set freq to 293.75
2023-06-11 13:53:00 chain = 1 set freq to 293.75
2023-06-11 13:53:00 chain = 2 set freq to 293.75
2023-06-11 13:53:00 chain = 0 set freq to 300.00
2023-06-11 13:53:00 chain = 1 set freq to 300.00
2023-06-11 13:53:00 chain = 2 set freq to 300.00
2023-06-11 13:53:01 chain = 0 set freq to 306.25
2023-06-11 13:53:01 chain = 1 set freq to 306.25
2023-06-11 13:53:01 chain = 2 set freq to 306.25
2023-06-11 13:53:01 chain = 0 set freq to 312.50
2023-06-11 13:53:01 chain = 1 set freq to 312.50
2023-06-11 13:53:01 chain = 2 set freq to 312.50
2023-06-11 13:53:01 chain = 0 set freq to 318.75
2023-06-11 13:53:01 chain = 1 set freq to 318.75
2023-06-11 13:53:01 chain = 2 set freq to 318.75
2023-06-11 13:53:02 chain = 0 set freq to 325.00
2023-06-11 13:53:02 chain = 1 set freq to 325.00
2023-06-11 13:53:02 chain = 2 set freq to 325.00
2023-06-11 13:53:02 chain = 0 set freq to 331.25
2023-06-11 13:53:02 chain = 1 set freq to 331.25
2023-06-11 13:53:02 chain = 2 set freq to 331.25
2023-06-11 13:53:02 chain = 0 set freq to 337.50
2023-06-11 13:53:02 chain = 1 set freq to 337.50
2023-06-11 13:53:02 chain = 2 set freq to 337.50
2023-06-11 13:53:03 chain = 0 set freq to 343.75
2023-06-11 13:53:03 chain = 1 set freq to 343.75
2023-06-11 13:53:03 chain = 2 set freq to 343.75
2023-06-11 13:53:03 chain = 0 set freq to 350.00
2023-06-11 13:53:03 chain = 1 set freq to 350.00
2023-06-11 13:53:03 chain = 2 set freq to 350.00
2023-06-11 13:53:03 chain = 0 set freq to 356.25
2023-06-11 13:53:03 chain = 1 set freq to 356.25
2023-06-11 13:53:03 chain = 2 set freq to 356.25
2023-06-11 13:53:03 chain = 0 set freq to 362.50
2023-06-11 13:53:03 chain = 1 set freq to 362.50
2023-06-11 13:53:03 chain = 2 set freq to 362.50
2023-06-11 13:53:04 chain = 0 set freq to 368.75
2023-06-11 13:53:04 chain = 1 set freq to 368.75
2023-06-11 13:53:04 chain = 2 set freq to 368.75
2023-06-11 13:53:04 chain = 0 set freq to 375.00
2023-06-11 13:53:04 chain = 1 set freq to 375.00
2023-06-11 13:53:04 chain = 2 set freq to 375.00
2023-06-11 13:53:04 chain = 0 set freq to 381.25
2023-06-11 13:53:04 chain = 1 set freq to 381.25
2023-06-11 13:53:04 chain = 2 set freq to 381.25
2023-06-11 13:53:05 chain = 0 set freq to 387.50
2023-06-11 13:53:05 chain = 1 set freq to 387.50
2023-06-11 13:53:05 chain = 2 set freq to 387.50
2023-06-11 13:53:05 chain = 0 set freq to 393.75
2023-06-11 13:53:05 chain = 1 set freq to 393.75
2023-06-11 13:53:05 chain = 2 set freq to 393.75
2023-06-11 13:53:05 chain = 0 set freq to 400.00
2023-06-11 13:53:05 chain = 1 set freq to 400.00
2023-06-11 13:53:05 chain = 2 set freq to 400.00
2023-06-11 13:53:06 chain = 0 set freq to 406.25
2023-06-11 13:53:06 chain = 1 set freq to 406.25
2023-06-11 13:53:06 chain = 2 set freq to 406.25
2023-06-11 13:53:06 chain = 0 set freq to 412.50
2023-06-11 13:53:06 chain = 1 set freq to 412.50
2023-06-11 13:53:06 chain = 2 set freq to 412.50
2023-06-11 13:53:06 chain = 0 set freq to 418.75
2023-06-11 13:53:06 chain = 1 set freq to 418.75
2023-06-11 13:53:06 chain = 2 set freq to 418.75
2023-06-11 13:53:07 chain = 0 set freq to 425.00
2023-06-11 13:53:07 chain = 1 set freq to 425.00
2023-06-11 13:53:07 chain = 2 set freq to 425.00
2023-06-11 13:53:07 chain = 0 set freq to 431.25
2023-06-11 13:53:07 chain = 1 set freq to 431.25
2023-06-11 13:53:07 chain = 2 set freq to 431.25
2023-06-11 13:53:07 chain = 0 set freq to 437.50
2023-06-11 13:53:07 chain = 1 set freq to 437.50
2023-06-11 13:53:07 chain = 2 set freq to 437.50
2023-06-11 13:53:07 chain = 0 set freq to 443.75
2023-06-11 13:53:07 chain = 1 set freq to 443.75
2023-06-11 13:53:07 chain = 2 set freq to 443.75
2023-06-11 13:53:08 chain = 0 set freq to 450.00
2023-06-11 13:53:08 chain = 1 set freq to 450.00
2023-06-11 13:53:08 chain = 2 set freq to 450.00
2023-06-11 13:53:08 chain = 0 set freq to 456.25
2023-06-11 13:53:08 chain = 1 set freq to 456.25
2023-06-11 13:53:08 chain = 2 set freq to 456.25
2023-06-11 13:53:08 chain = 0 set freq to 462.50
2023-06-11 13:53:08 chain = 1 set freq to 462.50
2023-06-11 13:53:08 chain = 2 set freq to 462.50
2023-06-11 13:53:09 chain = 0 set freq to 468.75
2023-06-11 13:53:09 chain = 1 set freq to 468.75
2023-06-11 13:53:09 chain = 2 set freq to 468.75
2023-06-11 13:53:09 chain = 0 set freq to 475.00
2023-06-11 13:53:09 chain = 1 set freq to 475.00
2023-06-11 13:53:09 chain = 2 set freq to 475.00
2023-06-11 13:53:09 chain = 0 set freq to 481.25
2023-06-11 13:53:09 chain = 1 set freq to 481.25
2023-06-11 13:53:09 chain = 2 set freq to 481.25
2023-06-11 13:53:10 chain = 0 set freq to 487.50
2023-06-11 13:53:10 chain = 1 set freq to 487.50
2023-06-11 13:53:10 chain = 2 set freq to 487.50
2023-06-11 13:53:10 chain = 0 set freq to 493.75
2023-06-11 13:53:10 chain = 1 set freq to 493.75
2023-06-11 13:53:10 chain = 2 set freq to 493.75
2023-06-11 13:53:10 chain = 0 set freq to 500.00
2023-06-11 13:53:10 chain = 1 set freq to 500.00
2023-06-11 13:53:10 chain = 2 set freq to 500.00
2023-06-11 13:53:10 chain = 0 set freq to 506.25
2023-06-11 13:53:10 chain = 1 set freq to 506.25
2023-06-11 13:53:10 chain = 2 set freq to 506.25
2023-06-11 13:53:11 chain = 0 set freq to 512.50
2023-06-11 13:53:11 chain = 1 set freq to 512.50
2023-06-11 13:53:11 chain = 2 set freq to 512.50
2023-06-11 13:53:11 chain = 0 set freq to 518.75
2023-06-11 13:53:11 chain = 1 set freq to 518.75
2023-06-11 13:53:11 chain = 2 set freq to 518.75
2023-06-11 13:53:11 chain = 0 set freq to 525.00
2023-06-11 13:53:11 chain = 1 set freq to 525.00
2023-06-11 13:53:11 chain = 2 set freq to 525.00
2023-06-11 13:53:12 enter mixed freq cfg
2023-06-11 13:53:12 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:53:12 start do_core_reset
2023-06-11 13:53:31 end do_core_reset
2023-06-11 13:53:41 set_voltage_by_steps to 1380.
2023-06-11 13:53:43 create thread pic_heart_beat_thread
2023-06-11 13:53:43 Init done!
2023-06-11 13:53:43 STATUS_OKAY
2023-06-11 13:53:43 start the cached job
2023-06-11 13:53:43 Version num 65536
2023-06-11 13:53:43 Mask num 0x1fffe000
2023-06-11 13:53:43 opt_multi_version = 65536, interval timeout = 2945120
2023-06-11 13:53:43 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-06-11 13:53:43 set_start_time_point total_tv_start_sys=273 total_tv_end_sys=274
2023-06-11 13:53:44 enable power watchdog: 0x0001
2023-06-11 13:54:16 set_voltage_by_steps to 1390.
2023-06-11 13:54:51 set_voltage_by_steps to 1400.
2023-06-11 12:59:02 Open miner sn file /config/sn error
2023-06-11 12:59:02 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-06-11 12:59:03 This is fix-freq version
2023-06-11 12:59:03 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-06-11 12:59:03 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-06-11 12:59:03 opt_multi_version = 1
2023-06-11 12:59:03 opt_bitmain_ab = 1
2023-06-11 12:59:03 mid_auto_gen = 1
2023-06-11 12:59:03 opt_bitmain_work_mode = 0
2023-06-11 12:59:03 port 439 already exported
2023-06-11 12:59:03 port 454 already exported
2023-06-11 12:59:03 port 440 already exported
2023-06-11 12:59:03 port 455 already exported
2023-06-11 12:59:03 port 441 already exported
2023-06-11 12:59:03 port 456 already exported
2023-06-11 12:59:03 port 438 already exported
2023-06-11 12:59:03 port 453 already exported
2023-06-11 12:59:03 port 446 already exported
2023-06-11 12:59:03 port 445 already exported
2023-06-11 12:59:03 Note: front fan is power on!
2023-06-11 12:59:03 Note: rear fan is power on!
2023-06-11 12:59:03 start the http log.
2023-06-11 12:59:03 httpListenThread start ret=0
2023-06-11 12:59:03 start listen on 6060 ...
2023-06-11 12:59:03 bad chain id = 3
2023-06-11 12:59:06 bad chain id = 3
2023-06-11 12:59:08 ==========================capability start==========================
2023-06-11 12:59:08 board num = 3
2023-06-11 12:59:08 board id = 0, chain num = 1
2023-06-11 12:59:08 chain id = 0
2023-06-11 12:59:08 board id = 1, chain num = 1
2023-06-11 12:59:08 chain id = 1
2023-06-11 12:59:08 board id = 2, chain num = 1
2023-06-11 12:59:08 chain id = 2
2023-06-11 12:59:08 ==========================capability end============================
2023-06-11 12:59:08 chain num = 3
2023-06-11 12:59:08 skip loading levels for now
2023-06-11 12:59:12 load chain 0 eeprom data
2023-06-11 12:59:15 load chain 1 eeprom data
2023-06-11 12:59:19 load chain 2 eeprom data
2023-06-11 12:59:19 i2c_sim_init start
2023-06-11 12:59:19 init gpio477
2023-06-11 12:59:19 init gpio476
2023-06-11 12:59:19 i2c_sim_init end
2023-06-11 12:59:20 power open power_version = 0x76
2023-06-11 12:59:23 power is not Calibrated
2023-06-11 12:59:24 miner type: Antminer S19j Pro
2023-06-11 12:59:24 multi machine mode
2023-06-11 12:59:24 load machine BHB42631 conf
2023-06-11 12:59:24 machine : BHB42631
2023-06-11 12:59:24 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-11 12:59:24 abandon mix board!
2023-06-11 12:59:24 abandon mix board!
2023-06-11 12:59:24 fan_eft : 0 fan_pwm : 100
2023-06-11 12:59:24 create thread get_nonce_and_register_thread
2023-06-11 12:59:24 fixed working voltage = 1380
2023-06-11 12:59:24 fixed frequency is 525
2023-06-11 12:59:24 Chain [0] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [0] BOM Version: 0x0010
2023-06-11 12:59:24 Chain [1] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [1] BOM Version: 0x0010
2023-06-11 12:59:24 Chain [2] PCB Version: 0x0110
2023-06-11 12:59:24 Chain [2] BOM Version: 0x0010
2023-06-11 12:59:24 bad chain id = 3
2023-06-11 12:59:24 Fan check passed.
2023-06-11 12:59:24 uart_trans addr:0xf6d72000.
2023-06-11 12:59:24 max sensor num = 4
2023-06-11 12:59:24 STATUS_INITED: soc init done!
2023-06-11 12:59:24 temperature_monitor_thread start...
2023-06-11 12:59:27 start to init...
2023-06-11 12:59:27 warning:power is not calibration.
2023-06-11 12:59:28 power type version: 0x0076
2023-06-11 12:59:30 disable power watchdog: 0x0000
2023-06-11 12:59:31 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-11 13:02:00 Slept 148 seconds, diff = 3.
2023-06-11 13:02:03 set_voltage_by_steps to 1500.
2023-06-11 13:02:13 start up min temp by 75a = 18
2023-06-11 13:02:16 Chain[0]: find 126 asic, times 0
2023-06-11 13:02:18 Chain[1]: find 126 asic, times 0
2023-06-11 13:02:20 Chain[2]: find 126 asic, times 0
2023-06-11 13:02:25 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:02:29 Bring up temperature is 19
2023-06-11 13:02:29 set UART baud to 3000000
2023-06-11 13:02:29 create thread check_miner_status_thread
2023-06-11 13:02:29 create thread check_system_work_thread
2023-06-11 13:02:29 set_voltage_by_steps to 1450.
2023-06-11 13:02:32 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:02:32 start do_core_reset
2023-06-11 13:02:51 end do_core_reset
2023-06-11 13:02:51 chain[0] min = 525 max =525
2023-06-11 13:02:51 chain[1] min = 525 max =525
2023-06-11 13:02:51 chain[2] min = 525 max =525
2023-06-11 13:02:51 1.inc all chain freq to 525
2023-06-11 13:02:51 fixed step freq_start = 50, freq_end = 525, freq_step = 6.25
2023-06-11 13:02:51 chain = 0 set freq to 56.25
2023-06-11 13:02:51 chain = 1 set freq to 56.25
2023-06-11 13:02:51 chain = 2 set freq to 56.25
2023-06-11 13:02:51 chain = 0 set freq to 62.50
2023-06-11 13:02:51 chain = 1 set freq to 62.50
2023-06-11 13:02:51 chain = 2 set freq to 62.50
2023-06-11 13:02:52 chain = 0 set freq to 68.75
2023-06-11 13:02:52 chain = 1 set freq to 68.75
2023-06-11 13:02:52 chain = 2 set freq to 68.75
2023-06-11 13:02:52 chain = 0 set freq to 75.00
2023-06-11 13:02:52 chain = 1 set freq to 75.00
2023-06-11 13:02:52 chain = 2 set freq to 75.00
2023-06-11 13:02:52 chain = 0 set freq to 81.25
2023-06-11 13:02:52 chain = 1 set freq to 81.25
2023-06-11 13:02:52 chain = 2 set freq to 81.25
2023-06-11 13:02:53 chain = 0 set freq to 87.50
2023-06-11 13:02:53 chain = 1 set freq to 87.50
2023-06-11 13:02:53 chain = 2 set freq to 87.50
2023-06-11 13:02:53 chain = 0 set freq to 93.75
2023-06-11 13:02:53 chain = 1 set freq to 93.75
2023-06-11 13:02:53 chain = 2 set freq to 93.75
2023-06-11 13:02:53 chain = 0 set freq to 100.00
2023-06-11 13:02:53 chain = 1 set freq to 100.00
2023-06-11 13:02:53 chain = 2 set freq to 100.00
2023-06-11 13:02:53 chain = 0 set freq to 106.25
2023-06-11 13:02:53 chain = 1 set freq to 106.25
2023-06-11 13:02:53 chain = 2 set freq to 106.25
2023-06-11 13:02:54 chain = 0 set freq to 112.50
2023-06-11 13:02:54 chain = 1 set freq to 112.50
2023-06-11 13:02:54 chain = 2 set freq to 112.50
2023-06-11 13:02:54 chain = 0 set freq to 118.75
2023-06-11 13:02:54 chain = 1 set freq to 118.75
2023-06-11 13:02:54 chain = 2 set freq to 118.75
2023-06-11 13:02:54 chain = 0 set freq to 125.00
2023-06-11 13:02:54 chain = 1 set freq to 125.00
2023-06-11 13:02:54 chain = 2 set freq to 125.00
2023-06-11 13:02:55 chain = 0 set freq to 131.25
2023-06-11 13:02:55 chain = 1 set freq to 131.25
2023-06-11 13:02:55 chain = 2 set freq to 131.25
2023-06-11 13:02:55 chain = 0 set freq to 137.50
2023-06-11 13:02:55 chain = 1 set freq to 137.50
2023-06-11 13:02:55 chain = 2 set freq to 137.50
2023-06-11 13:02:55 chain = 0 set freq to 143.75
2023-06-11 13:02:55 chain = 1 set freq to 143.75
2023-06-11 13:02:55 chain = 2 set freq to 143.75
2023-06-11 13:02:56 chain = 0 set freq to 150.00
2023-06-11 13:02:56 chain = 1 set freq to 150.00
2023-06-11 13:02:56 chain = 2 set freq to 150.00
2023-06-11 13:02:56 chain = 0 set freq to 156.25
2023-06-11 13:02:56 chain = 1 set freq to 156.25
2023-06-11 13:02:56 chain = 2 set freq to 156.25
2023-06-11 13:02:56 chain = 0 set freq to 162.50
2023-06-11 13:02:56 chain = 1 set freq to 162.50
2023-06-11 13:02:56 chain = 2 set freq to 162.50
2023-06-11 13:02:56 chain = 0 set freq to 168.75
2023-06-11 13:02:56 chain = 1 set freq to 168.75
2023-06-11 13:02:56 chain = 2 set freq to 168.75
2023-06-11 13:02:57 chain = 0 set freq to 175.00
2023-06-11 13:02:57 chain = 1 set freq to 175.00
2023-06-11 13:02:57 chain = 2 set freq to 175.00
2023-06-11 13:02:57 chain = 0 set freq to 181.25
2023-06-11 13:02:57 chain = 1 set freq to 181.25
2023-06-11 13:02:57 chain = 2 set freq to 181.25
2023-06-11 13:02:57 chain = 0 set freq to 187.50
2023-06-11 13:02:57 chain = 1 set freq to 187.50
2023-06-11 13:02:57 chain = 2 set freq to 187.50
2023-06-11 13:02:58 chain = 0 set freq to 193.75
2023-06-11 13:02:58 chain = 1 set freq to 193.75
2023-06-11 13:02:58 chain = 2 set freq to 193.75
2023-06-11 13:02:58 chain = 0 set freq to 200.00
2023-06-11 13:02:58 chain = 1 set freq to 200.00
2023-06-11 13:02:58 chain = 2 set freq to 200.00
2023-06-11 13:02:58 chain = 0 set freq to 206.25
2023-06-11 13:02:58 chain = 1 set freq to 206.25
2023-06-11 13:02:58 chain = 2 set freq to 206.25
2023-06-11 13:02:59 chain = 0 set freq to 212.50
2023-06-11 13:02:59 chain = 1 set freq to 212.50
2023-06-11 13:02:59 chain = 2 set freq to 212.50
2023-06-11 13:02:59 chain = 0 set freq to 218.75
2023-06-11 13:02:59 chain = 1 set freq to 218.75
2023-06-11 13:02:59 chain = 2 set freq to 218.75
2023-06-11 13:02:59 chain = 0 set freq to 225.00
2023-06-11 13:02:59 chain = 1 set freq to 225.00
2023-06-11 13:02:59 chain = 2 set freq to 225.00
2023-06-11 13:02:59 chain = 0 set freq to 231.25
2023-06-11 13:02:59 chain = 1 set freq to 231.25
2023-06-11 13:02:59 chain = 2 set freq to 231.25
2023-06-11 13:03:00 chain = 0 set freq to 237.50
2023-06-11 13:03:00 chain = 1 set freq to 237.50
2023-06-11 13:03:00 chain = 2 set freq to 237.50
2023-06-11 13:03:00 chain = 0 set freq to 243.75
2023-06-11 13:03:00 chain = 1 set freq to 243.75
2023-06-11 13:03:00 chain = 2 set freq to 243.75
2023-06-11 13:03:00 chain = 0 set freq to 250.00
2023-06-11 13:03:00 chain = 1 set freq to 250.00
2023-06-11 13:03:00 chain = 2 set freq to 250.00
2023-06-11 13:03:01 chain = 0 set freq to 256.25
2023-06-11 13:03:01 chain = 1 set freq to 256.25
2023-06-11 13:03:01 chain = 2 set freq to 256.25
2023-06-11 13:03:01 chain = 0 set freq to 262.50
2023-06-11 13:03:01 chain = 1 set freq to 262.50
2023-06-11 13:03:01 chain = 2 set freq to 262.50
2023-06-11 13:03:01 chain = 0 set freq to 268.75
2023-06-11 13:03:01 chain = 1 set freq to 268.75
2023-06-11 13:03:01 chain = 2 set freq to 268.75
2023-06-11 13:03:02 chain = 0 set freq to 275.00
2023-06-11 13:03:02 chain = 1 set freq to 275.00
2023-06-11 13:03:02 chain = 2 set freq to 275.00
2023-06-11 13:03:02 chain = 0 set freq to 281.25
2023-06-11 13:03:02 chain = 1 set freq to 281.25
2023-06-11 13:03:02 chain = 2 set freq to 281.25
2023-06-11 13:03:02 chain = 0 set freq to 287.50
2023-06-11 13:03:02 chain = 1 set freq to 287.50
2023-06-11 13:03:02 chain = 2 set freq to 287.50
2023-06-11 13:03:02 chain = 0 set freq to 293.75
2023-06-11 13:03:02 chain = 1 set freq to 293.75
2023-06-11 13:03:02 chain = 2 set freq to 293.75
2023-06-11 13:03:03 chain = 0 set freq to 300.00
2023-06-11 13:03:03 chain = 1 set freq to 300.00
2023-06-11 13:03:03 chain = 2 set freq to 300.00
2023-06-11 13:03:03 chain = 0 set freq to 306.25
2023-06-11 13:03:03 chain = 1 set freq to 306.25
2023-06-11 13:03:03 chain = 2 set freq to 306.25
2023-06-11 13:03:03 chain = 0 set freq to 312.50
2023-06-11 13:03:03 chain = 1 set freq to 312.50
2023-06-11 13:03:03 chain = 2 set freq to 312.50
2023-06-11 13:03:04 chain = 0 set freq to 318.75
2023-06-11 13:03:04 chain = 1 set freq to 318.75
2023-06-11 13:03:04 chain = 2 set freq to 318.75
2023-06-11 13:03:04 chain = 0 set freq to 325.00
2023-06-11 13:03:04 chain = 1 set freq to 325.00
2023-06-11 13:03:04 chain = 2 set freq to 325.00
2023-06-11 13:03:04 chain = 0 set freq to 331.25
2023-06-11 13:03:04 chain = 1 set freq to 331.25
2023-06-11 13:03:04 chain = 2 set freq to 331.25
2023-06-11 13:03:05 chain = 0 set freq to 337.50
2023-06-11 13:03:05 chain = 1 set freq to 337.50
2023-06-11 13:03:05 chain = 2 set freq to 337.50
2023-06-11 13:03:05 chain = 0 set freq to 343.75
2023-06-11 13:03:05 chain = 1 set freq to 343.75
2023-06-11 13:03:05 chain = 2 set freq to 343.75
2023-06-11 13:03:05 chain = 0 set freq to 350.00
2023-06-11 13:03:05 chain = 1 set freq to 350.00
2023-06-11 13:03:05 chain = 2 set freq to 350.00
2023-06-11 13:03:06 chain = 0 set freq to 356.25
2023-06-11 13:03:06 chain = 1 set freq to 356.25
2023-06-11 13:03:06 chain = 2 set freq to 356.25
2023-06-11 13:03:06 chain = 0 set freq to 362.50
2023-06-11 13:03:06 chain = 1 set freq to 362.50
2023-06-11 13:03:06 chain = 2 set freq to 362.50
2023-06-11 13:03:06 chain = 0 set freq to 368.75
2023-06-11 13:03:06 chain = 1 set freq to 368.75
2023-06-11 13:03:06 chain = 2 set freq to 368.75
2023-06-11 13:03:06 chain = 0 set freq to 375.00
2023-06-11 13:03:06 chain = 1 set freq to 375.00
2023-06-11 13:03:06 chain = 2 set freq to 375.00
2023-06-11 13:03:07 chain = 0 set freq to 381.25
2023-06-11 13:03:07 chain = 1 set freq to 381.25
2023-06-11 13:03:07 chain = 2 set freq to 381.25
2023-06-11 13:03:07 chain = 0 set freq to 387.50
2023-06-11 13:03:07 chain = 1 set freq to 387.50
2023-06-11 13:03:07 chain = 2 set freq to 387.50
2023-06-11 13:03:07 chain = 0 set freq to 393.75
2023-06-11 13:03:07 chain = 1 set freq to 393.75
2023-06-11 13:03:07 chain = 2 set freq to 393.75
2023-06-11 13:03:08 chain = 0 set freq to 400.00
2023-06-11 13:03:08 chain = 1 set freq to 400.00
2023-06-11 13:03:08 chain = 2 set freq to 400.00
2023-06-11 13:03:08 chain = 0 set freq to 406.25
2023-06-11 13:03:08 chain = 1 set freq to 406.25
2023-06-11 13:03:08 chain = 2 set freq to 406.25
2023-06-11 13:03:08 chain = 0 set freq to 412.50
2023-06-11 13:03:08 chain = 1 set freq to 412.50
2023-06-11 13:03:08 chain = 2 set freq to 412.50
2023-06-11 13:03:09 chain = 0 set freq to 418.75
2023-06-11 13:03:09 chain = 1 set freq to 418.75
2023-06-11 13:03:09 chain = 2 set freq to 418.75
2023-06-11 13:03:09 chain = 0 set freq to 425.00
2023-06-11 13:03:09 chain = 1 set freq to 425.00
2023-06-11 13:03:09 chain = 2 set freq to 425.00
2023-06-11 13:03:09 chain = 0 set freq to 431.25
2023-06-11 13:03:09 chain = 1 set freq to 431.25
2023-06-11 13:03:09 chain = 2 set freq to 431.25
2023-06-11 13:03:09 chain = 0 set freq to 437.50
2023-06-11 13:03:09 chain = 1 set freq to 437.50
2023-06-11 13:03:09 chain = 2 set freq to 437.50
2023-06-11 13:03:10 chain = 0 set freq to 443.75
2023-06-11 13:03:10 chain = 1 set freq to 443.75
2023-06-11 13:03:10 chain = 2 set freq to 443.75
2023-06-11 13:03:10 chain = 0 set freq to 450.00
2023-06-11 13:03:10 chain = 1 set freq to 450.00
2023-06-11 13:03:10 chain = 2 set freq to 450.00
2023-06-11 13:03:10 chain = 0 set freq to 456.25
2023-06-11 13:03:10 chain = 1 set freq to 456.25
2023-06-11 13:03:10 chain = 2 set freq to 456.25
2023-06-11 13:03:11 chain = 0 set freq to 462.50
2023-06-11 13:03:11 chain = 1 set freq to 462.50
2023-06-11 13:03:11 chain = 2 set freq to 462.50
2023-06-11 13:03:11 chain = 0 set freq to 468.75
2023-06-11 13:03:11 chain = 1 set freq to 468.75
2023-06-11 13:03:11 chain = 2 set freq to 468.75
2023-06-11 13:03:11 chain = 0 set freq to 475.00
2023-06-11 13:03:11 chain = 1 set freq to 475.00
2023-06-11 13:03:11 chain = 2 set freq to 475.00
2023-06-11 13:03:12 chain = 0 set freq to 481.25
2023-06-11 13:03:12 chain = 1 set freq to 481.25
2023-06-11 13:03:12 chain = 2 set freq to 481.25
2023-06-11 13:03:12 chain = 0 set freq to 487.50
2023-06-11 13:03:12 chain = 1 set freq to 487.50
2023-06-11 13:03:12 chain = 2 set freq to 487.50
2023-06-11 13:03:12 chain = 0 set freq to 493.75
2023-06-11 13:03:12 chain = 1 set freq to 493.75
2023-06-11 13:03:12 chain = 2 set freq to 493.75
2023-06-11 13:03:12 chain = 0 set freq to 500.00
2023-06-11 13:03:12 chain = 1 set freq to 500.00
2023-06-11 13:03:12 chain = 2 set freq to 500.00
2023-06-11 13:03:13 chain = 0 set freq to 506.25
2023-06-11 13:03:13 chain = 1 set freq to 506.25
2023-06-11 13:03:13 chain = 2 set freq to 506.25
2023-06-11 13:03:13 chain = 0 set freq to 512.50
2023-06-11 13:03:13 chain = 1 set freq to 512.50
2023-06-11 13:03:13 chain = 2 set freq to 512.50
2023-06-11 13:03:13 chain = 0 set freq to 518.75
2023-06-11 13:03:13 chain = 1 set freq to 518.75
2023-06-11 13:03:13 chain = 2 set freq to 518.75
2023-06-11 13:03:14 chain = 0 set freq to 525.00
2023-06-11 13:03:14 chain = 1 set freq to 525.00
2023-06-11 13:03:14 chain = 2 set freq to 525.00
2023-06-11 13:03:14 enter mixed freq cfg
2023-06-11 13:03:14 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:03:14 start do_core_reset
2023-06-11 13:03:33 end do_core_reset
2023-06-11 13:03:43 set_voltage_by_steps to 1383.
2023-06-11 13:03:45 create thread pic_heart_beat_thread
2023-06-11 13:03:45 Init done!
2023-06-11 13:03:45 STATUS_OKAY
2023-06-11 13:03:45 start the cached job
2023-06-11 13:03:45 Version num 65536
2023-06-11 13:03:45 Mask num 0x1fffe000
2023-06-11 13:03:45 opt_multi_version = 65536, interval timeout = 2945120
2023-06-11 13:03:45 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-06-11 13:03:45 set_start_time_point total_tv_start_sys=293 total_tv_end_sys=294
2023-06-11 13:03:46 enable power watchdog: 0x0001
2023-06-11 13:04:22 set_voltage_by_steps to 1393.
2023-06-11 13:04:44 set_voltage_by_steps to 1403.
2023-06-11 13:32:31 avg rate is lower than ideal rate, 68024.48 in 28 mins
2023-06-11 13:32:31 30m avg rate is 68024.48 in 28 mins
2023-06-11 13:48:56 ****power off hashboard****
2023-06-11 13:49:20 Open miner sn file /config/sn error
2023-06-11 13:49:20 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :
2023-06-11 13:49:21 This is fix-freq version
2023-06-11 13:49:21 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2023-06-11 13:49:21 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-06-11 13:49:21 opt_multi_version = 1
2023-06-11 13:49:21 opt_bitmain_ab = 1
2023-06-11 13:49:21 mid_auto_gen = 1
2023-06-11 13:49:21 opt_bitmain_work_mode = 0
2023-06-11 13:49:21 port 439 already exported
2023-06-11 13:49:21 port 454 already exported
2023-06-11 13:49:21 port 440 already exported
2023-06-11 13:49:21 port 455 already exported
2023-06-11 13:49:21 port 441 already exported
2023-06-11 13:49:21 port 456 already exported
2023-06-11 13:49:21 port 438 already exported
2023-06-11 13:49:21 port 453 already exported
2023-06-11 13:49:21 port 446 already exported
2023-06-11 13:49:21 port 445 already exported
2023-06-11 13:49:21 Note: front fan is power on!
2023-06-11 13:49:21 Note: rear fan is power on!
2023-06-11 13:49:21 start the http log.
2023-06-11 13:49:21 httpListenThread start ret=0
2023-06-11 13:49:21 start listen on 6060 ...
2023-06-11 13:49:21 bad chain id = 3
2023-06-11 13:49:24 bad chain id = 3
2023-06-11 13:49:26 ==========================capability start==========================
2023-06-11 13:49:26 board num = 3
2023-06-11 13:49:26 board id = 0, chain num = 1
2023-06-11 13:49:26 chain id = 0
2023-06-11 13:49:26 board id = 1, chain num = 1
2023-06-11 13:49:26 chain id = 1
2023-06-11 13:49:26 board id = 2, chain num = 1
2023-06-11 13:49:26 chain id = 2
2023-06-11 13:49:26 ==========================capability end============================
2023-06-11 13:49:26 chain num = 3
2023-06-11 13:49:26 skip loading levels for now
2023-06-11 13:49:30 load chain 0 eeprom data
2023-06-11 13:49:33 load chain 1 eeprom data
2023-06-11 13:49:36 load chain 2 eeprom data
2023-06-11 13:49:36 i2c_sim_init start
2023-06-11 13:49:36 init gpio477
2023-06-11 13:49:36 init gpio476
2023-06-11 13:49:36 i2c_sim_init end
2023-06-11 13:49:38 power open power_version = 0x76
2023-06-11 13:49:40 power is not Calibrated
2023-06-11 13:49:42 miner type: Antminer S19j Pro
2023-06-11 13:49:42 multi machine mode
2023-06-11 13:49:42 load machine BHB42631 conf
2023-06-11 13:49:42 machine : BHB42631
2023-06-11 13:49:42 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-06-11 13:49:42 abandon mix board!
2023-06-11 13:49:42 abandon mix board!
2023-06-11 13:49:42 fan_eft : 0 fan_pwm : 100
2023-06-11 13:49:42 create thread get_nonce_and_register_thread
2023-06-11 13:49:42 fixed working voltage = 1380
2023-06-11 13:49:42 fixed frequency is 525
2023-06-11 13:49:42 Chain [0] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [0] BOM Version: 0x0010
2023-06-11 13:49:42 Chain [1] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [1] BOM Version: 0x0010
2023-06-11 13:49:42 Chain [2] PCB Version: 0x0110
2023-06-11 13:49:42 Chain [2] BOM Version: 0x0010
2023-06-11 13:49:42 bad chain id = 3
2023-06-11 13:49:42 Fan check passed.
2023-06-11 13:49:42 uart_trans addr:0xf71d1000.
2023-06-11 13:49:42 max sensor num = 4
2023-06-11 13:49:42 STATUS_INITED: soc init done!
2023-06-11 13:49:42 temperature_monitor_thread start...
2023-06-11 13:49:45 start to init...
2023-06-11 13:49:45 warning:power is not calibration.
2023-06-11 13:49:46 power type version: 0x0076
2023-06-11 13:49:47 disable power watchdog: 0x0000
2023-06-11 13:49:48 Initializing the power, please wait, this may take up to 2 minutes...
2023-06-11 13:51:57 Slept 128 seconds, diff = 3.
2023-06-11 13:52:01 set_voltage_by_steps to 1500.
2023-06-11 13:52:11 start up min temp by 75a = 19
2023-06-11 13:52:14 Chain[0]: find 126 asic, times 0
2023-06-11 13:52:16 Chain[1]: find 126 asic, times 0
2023-06-11 13:52:18 Chain[2]: find 126 asic, times 0
2023-06-11 13:52:23 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:52:27 Bring up temperature is 20
2023-06-11 13:52:27 set UART baud to 3000000
2023-06-11 13:52:27 create thread check_miner_status_thread
2023-06-11 13:52:27 create thread check_system_work_thread
2023-06-11 13:52:27 set_voltage_by_steps to 1450.
2023-06-11 13:52:30 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:52:30 start do_core_reset
2023-06-11 13:52:49 end do_core_reset
2023-06-11 13:52:49 chain[0] min = 525 max =525
2023-06-11 13:52:49 chain[1] min = 525 max =525
2023-06-11 13:52:49 chain[2] min = 525 max =525
2023-06-11 13:52:49 1.inc all chain freq to 525
2023-06-11 13:52:49 fixed step freq_start = 50, freq_end = 525, freq_step = 6.25
2023-06-11 13:52:49 chain = 0 set freq to 56.25
2023-06-11 13:52:49 chain = 1 set freq to 56.25
2023-06-11 13:52:49 chain = 2 set freq to 56.25
2023-06-11 13:52:49 chain = 0 set freq to 62.50
2023-06-11 13:52:49 chain = 1 set freq to 62.50
2023-06-11 13:52:49 chain = 2 set freq to 62.50
2023-06-11 13:52:49 chain = 0 set freq to 68.75
2023-06-11 13:52:49 chain = 1 set freq to 68.75
2023-06-11 13:52:49 chain = 2 set freq to 68.75
2023-06-11 13:52:50 chain = 0 set freq to 75.00
2023-06-11 13:52:50 chain = 1 set freq to 75.00
2023-06-11 13:52:50 chain = 2 set freq to 75.00
2023-06-11 13:52:50 chain = 0 set freq to 81.25
2023-06-11 13:52:50 chain = 1 set freq to 81.25
2023-06-11 13:52:50 chain = 2 set freq to 81.25
2023-06-11 13:52:50 chain = 0 set freq to 87.50
2023-06-11 13:52:50 chain = 1 set freq to 87.50
2023-06-11 13:52:50 chain = 2 set freq to 87.50
2023-06-11 13:52:51 chain = 0 set freq to 93.75
2023-06-11 13:52:51 chain = 1 set freq to 93.75
2023-06-11 13:52:51 chain = 2 set freq to 93.75
2023-06-11 13:52:51 chain = 0 set freq to 100.00
2023-06-11 13:52:51 chain = 1 set freq to 100.00
2023-06-11 13:52:51 chain = 2 set freq to 100.00
2023-06-11 13:52:51 chain = 0 set freq to 106.25
2023-06-11 13:52:51 chain = 1 set freq to 106.25
2023-06-11 13:52:51 chain = 2 set freq to 106.25
2023-06-11 13:52:51 chain = 0 set freq to 112.50
2023-06-11 13:52:51 chain = 1 set freq to 112.50
2023-06-11 13:52:51 chain = 2 set freq to 112.50
2023-06-11 13:52:52 chain = 0 set freq to 118.75
2023-06-11 13:52:52 chain = 1 set freq to 118.75
2023-06-11 13:52:52 chain = 2 set freq to 118.75
2023-06-11 13:52:52 chain = 0 set freq to 125.00
2023-06-11 13:52:52 chain = 1 set freq to 125.00
2023-06-11 13:52:52 chain = 2 set freq to 125.00
2023-06-11 13:52:52 chain = 0 set freq to 131.25
2023-06-11 13:52:52 chain = 1 set freq to 131.25
2023-06-11 13:52:52 chain = 2 set freq to 131.25
2023-06-11 13:52:53 chain = 0 set freq to 137.50
2023-06-11 13:52:53 chain = 1 set freq to 137.50
2023-06-11 13:52:53 chain = 2 set freq to 137.50
2023-06-11 13:52:53 chain = 0 set freq to 143.75
2023-06-11 13:52:53 chain = 1 set freq to 143.75
2023-06-11 13:52:53 chain = 2 set freq to 143.75
2023-06-11 13:52:53 chain = 0 set freq to 150.00
2023-06-11 13:52:53 chain = 1 set freq to 150.00
2023-06-11 13:52:53 chain = 2 set freq to 150.00
2023-06-11 13:52:54 chain = 0 set freq to 156.25
2023-06-11 13:52:54 chain = 1 set freq to 156.25
2023-06-11 13:52:54 chain = 2 set freq to 156.25
2023-06-11 13:52:54 chain = 0 set freq to 162.50
2023-06-11 13:52:54 chain = 1 set freq to 162.50
2023-06-11 13:52:54 chain = 2 set freq to 162.50
2023-06-11 13:52:54 chain = 0 set freq to 168.75
2023-06-11 13:52:54 chain = 1 set freq to 168.75
2023-06-11 13:52:54 chain = 2 set freq to 168.75
2023-06-11 13:52:54 chain = 0 set freq to 175.00
2023-06-11 13:52:54 chain = 1 set freq to 175.00
2023-06-11 13:52:54 chain = 2 set freq to 175.00
2023-06-11 13:52:55 chain = 0 set freq to 181.25
2023-06-11 13:52:55 chain = 1 set freq to 181.25
2023-06-11 13:52:55 chain = 2 set freq to 181.25
2023-06-11 13:52:55 chain = 0 set freq to 187.50
2023-06-11 13:52:55 chain = 1 set freq to 187.50
2023-06-11 13:52:55 chain = 2 set freq to 187.50
2023-06-11 13:52:55 chain = 0 set freq to 193.75
2023-06-11 13:52:55 chain = 1 set freq to 193.75
2023-06-11 13:52:55 chain = 2 set freq to 193.75
2023-06-11 13:52:56 chain = 0 set freq to 200.00
2023-06-11 13:52:56 chain = 1 set freq to 200.00
2023-06-11 13:52:56 chain = 2 set freq to 200.00
2023-06-11 13:52:56 chain = 0 set freq to 206.25
2023-06-11 13:52:56 chain = 1 set freq to 206.25
2023-06-11 13:52:56 chain = 2 set freq to 206.25
2023-06-11 13:52:56 chain = 0 set freq to 212.50
2023-06-11 13:52:56 chain = 1 set freq to 212.50
2023-06-11 13:52:56 chain = 2 set freq to 212.50
2023-06-11 13:52:57 chain = 0 set freq to 218.75
2023-06-11 13:52:57 chain = 1 set freq to 218.75
2023-06-11 13:52:57 chain = 2 set freq to 218.75
2023-06-11 13:52:57 chain = 0 set freq to 225.00
2023-06-11 13:52:57 chain = 1 set freq to 225.00
2023-06-11 13:52:57 chain = 2 set freq to 225.00
2023-06-11 13:52:57 chain = 0 set freq to 231.25
2023-06-11 13:52:57 chain = 1 set freq to 231.25
2023-06-11 13:52:57 chain = 2 set freq to 231.25
2023-06-11 13:52:57 chain = 0 set freq to 237.50
2023-06-11 13:52:57 chain = 1 set freq to 237.50
2023-06-11 13:52:57 chain = 2 set freq to 237.50
2023-06-11 13:52:58 chain = 0 set freq to 243.75
2023-06-11 13:52:58 chain = 1 set freq to 243.75
2023-06-11 13:52:58 chain = 2 set freq to 243.75
2023-06-11 13:52:58 chain = 0 set freq to 250.00
2023-06-11 13:52:58 chain = 1 set freq to 250.00
2023-06-11 13:52:58 chain = 2 set freq to 250.00
2023-06-11 13:52:58 chain = 0 set freq to 256.25
2023-06-11 13:52:58 chain = 1 set freq to 256.25
2023-06-11 13:52:58 chain = 2 set freq to 256.25
2023-06-11 13:52:59 chain = 0 set freq to 262.50
2023-06-11 13:52:59 chain = 1 set freq to 262.50
2023-06-11 13:52:59 chain = 2 set freq to 262.50
2023-06-11 13:52:59 chain = 0 set freq to 268.75
2023-06-11 13:52:59 chain = 1 set freq to 268.75
2023-06-11 13:52:59 chain = 2 set freq to 268.75
2023-06-11 13:52:59 chain = 0 set freq to 275.00
2023-06-11 13:52:59 chain = 1 set freq to 275.00
2023-06-11 13:52:59 chain = 2 set freq to 275.00
2023-06-11 13:53:00 chain = 0 set freq to 281.25
2023-06-11 13:53:00 chain = 1 set freq to 281.25
2023-06-11 13:53:00 chain = 2 set freq to 281.25
2023-06-11 13:53:00 chain = 0 set freq to 287.50
2023-06-11 13:53:00 chain = 1 set freq to 287.50
2023-06-11 13:53:00 chain = 2 set freq to 287.50
2023-06-11 13:53:00 chain = 0 set freq to 293.75
2023-06-11 13:53:00 chain = 1 set freq to 293.75
2023-06-11 13:53:00 chain = 2 set freq to 293.75
2023-06-11 13:53:00 chain = 0 set freq to 300.00
2023-06-11 13:53:00 chain = 1 set freq to 300.00
2023-06-11 13:53:00 chain = 2 set freq to 300.00
2023-06-11 13:53:01 chain = 0 set freq to 306.25
2023-06-11 13:53:01 chain = 1 set freq to 306.25
2023-06-11 13:53:01 chain = 2 set freq to 306.25
2023-06-11 13:53:01 chain = 0 set freq to 312.50
2023-06-11 13:53:01 chain = 1 set freq to 312.50
2023-06-11 13:53:01 chain = 2 set freq to 312.50
2023-06-11 13:53:01 chain = 0 set freq to 318.75
2023-06-11 13:53:01 chain = 1 set freq to 318.75
2023-06-11 13:53:01 chain = 2 set freq to 318.75
2023-06-11 13:53:02 chain = 0 set freq to 325.00
2023-06-11 13:53:02 chain = 1 set freq to 325.00
2023-06-11 13:53:02 chain = 2 set freq to 325.00
2023-06-11 13:53:02 chain = 0 set freq to 331.25
2023-06-11 13:53:02 chain = 1 set freq to 331.25
2023-06-11 13:53:02 chain = 2 set freq to 331.25
2023-06-11 13:53:02 chain = 0 set freq to 337.50
2023-06-11 13:53:02 chain = 1 set freq to 337.50
2023-06-11 13:53:02 chain = 2 set freq to 337.50
2023-06-11 13:53:03 chain = 0 set freq to 343.75
2023-06-11 13:53:03 chain = 1 set freq to 343.75
2023-06-11 13:53:03 chain = 2 set freq to 343.75
2023-06-11 13:53:03 chain = 0 set freq to 350.00
2023-06-11 13:53:03 chain = 1 set freq to 350.00
2023-06-11 13:53:03 chain = 2 set freq to 350.00
2023-06-11 13:53:03 chain = 0 set freq to 356.25
2023-06-11 13:53:03 chain = 1 set freq to 356.25
2023-06-11 13:53:03 chain = 2 set freq to 356.25
2023-06-11 13:53:03 chain = 0 set freq to 362.50
2023-06-11 13:53:03 chain = 1 set freq to 362.50
2023-06-11 13:53:03 chain = 2 set freq to 362.50
2023-06-11 13:53:04 chain = 0 set freq to 368.75
2023-06-11 13:53:04 chain = 1 set freq to 368.75
2023-06-11 13:53:04 chain = 2 set freq to 368.75
2023-06-11 13:53:04 chain = 0 set freq to 375.00
2023-06-11 13:53:04 chain = 1 set freq to 375.00
2023-06-11 13:53:04 chain = 2 set freq to 375.00
2023-06-11 13:53:04 chain = 0 set freq to 381.25
2023-06-11 13:53:04 chain = 1 set freq to 381.25
2023-06-11 13:53:04 chain = 2 set freq to 381.25
2023-06-11 13:53:05 chain = 0 set freq to 387.50
2023-06-11 13:53:05 chain = 1 set freq to 387.50
2023-06-11 13:53:05 chain = 2 set freq to 387.50
2023-06-11 13:53:05 chain = 0 set freq to 393.75
2023-06-11 13:53:05 chain = 1 set freq to 393.75
2023-06-11 13:53:05 chain = 2 set freq to 393.75
2023-06-11 13:53:05 chain = 0 set freq to 400.00
2023-06-11 13:53:05 chain = 1 set freq to 400.00
2023-06-11 13:53:05 chain = 2 set freq to 400.00
2023-06-11 13:53:06 chain = 0 set freq to 406.25
2023-06-11 13:53:06 chain = 1 set freq to 406.25
2023-06-11 13:53:06 chain = 2 set freq to 406.25
2023-06-11 13:53:06 chain = 0 set freq to 412.50
2023-06-11 13:53:06 chain = 1 set freq to 412.50
2023-06-11 13:53:06 chain = 2 set freq to 412.50
2023-06-11 13:53:06 chain = 0 set freq to 418.75
2023-06-11 13:53:06 chain = 1 set freq to 418.75
2023-06-11 13:53:06 chain = 2 set freq to 418.75
2023-06-11 13:53:07 chain = 0 set freq to 425.00
2023-06-11 13:53:07 chain = 1 set freq to 425.00
2023-06-11 13:53:07 chain = 2 set freq to 425.00
2023-06-11 13:53:07 chain = 0 set freq to 431.25
2023-06-11 13:53:07 chain = 1 set freq to 431.25
2023-06-11 13:53:07 chain = 2 set freq to 431.25
2023-06-11 13:53:07 chain = 0 set freq to 437.50
2023-06-11 13:53:07 chain = 1 set freq to 437.50
2023-06-11 13:53:07 chain = 2 set freq to 437.50
2023-06-11 13:53:07 chain = 0 set freq to 443.75
2023-06-11 13:53:07 chain = 1 set freq to 443.75
2023-06-11 13:53:07 chain = 2 set freq to 443.75
2023-06-11 13:53:08 chain = 0 set freq to 450.00
2023-06-11 13:53:08 chain = 1 set freq to 450.00
2023-06-11 13:53:08 chain = 2 set freq to 450.00
2023-06-11 13:53:08 chain = 0 set freq to 456.25
2023-06-11 13:53:08 chain = 1 set freq to 456.25
2023-06-11 13:53:08 chain = 2 set freq to 456.25
2023-06-11 13:53:08 chain = 0 set freq to 462.50
2023-06-11 13:53:08 chain = 1 set freq to 462.50
2023-06-11 13:53:08 chain = 2 set freq to 462.50
2023-06-11 13:53:09 chain = 0 set freq to 468.75
2023-06-11 13:53:09 chain = 1 set freq to 468.75
2023-06-11 13:53:09 chain = 2 set freq to 468.75
2023-06-11 13:53:09 chain = 0 set freq to 475.00
2023-06-11 13:53:09 chain = 1 set freq to 475.00
2023-06-11 13:53:09 chain = 2 set freq to 475.00
2023-06-11 13:53:09 chain = 0 set freq to 481.25
2023-06-11 13:53:09 chain = 1 set freq to 481.25
2023-06-11 13:53:09 chain = 2 set freq to 481.25
2023-06-11 13:53:10 chain = 0 set freq to 487.50
2023-06-11 13:53:10 chain = 1 set freq to 487.50
2023-06-11 13:53:10 chain = 2 set freq to 487.50
2023-06-11 13:53:10 chain = 0 set freq to 493.75
2023-06-11 13:53:10 chain = 1 set freq to 493.75
2023-06-11 13:53:10 chain = 2 set freq to 493.75
2023-06-11 13:53:10 chain = 0 set freq to 500.00
2023-06-11 13:53:10 chain = 1 set freq to 500.00
2023-06-11 13:53:10 chain = 2 set freq to 500.00
2023-06-11 13:53:10 chain = 0 set freq to 506.25
2023-06-11 13:53:10 chain = 1 set freq to 506.25
2023-06-11 13:53:10 chain = 2 set freq to 506.25
2023-06-11 13:53:11 chain = 0 set freq to 512.50
2023-06-11 13:53:11 chain = 1 set freq to 512.50
2023-06-11 13:53:11 chain = 2 set freq to 512.50
2023-06-11 13:53:11 chain = 0 set freq to 518.75
2023-06-11 13:53:11 chain = 1 set freq to 518.75
2023-06-11 13:53:11 chain = 2 set freq to 518.75
2023-06-11 13:53:11 chain = 0 set freq to 525.00
2023-06-11 13:53:11 chain = 1 set freq to 525.00
2023-06-11 13:53:11 chain = 2 set freq to 525.00
2023-06-11 13:53:12 enter mixed freq cfg
2023-06-11 13:53:12 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-06-11 13:53:12 start do_core_reset
2023-06-11 13:53:31 end do_core_reset
2023-06-11 13:53:41 set_voltage_by_steps to 1380.
2023-06-11 13:53:43 create thread pic_heart_beat_thread
2023-06-11 13:53:43 Init done!
2023-06-11 13:53:43 STATUS_OKAY
2023-06-11 13:53:43 start the cached job
2023-06-11 13:53:43 Version num 65536
2023-06-11 13:53:43 Mask num 0x1fffe000
2023-06-11 13:53:43 opt_multi_version = 65536, interval timeout = 2945120
2023-06-11 13:53:43 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-06-11 13:53:43 set_start_time_point total_tv_start_sys=273 total_tv_end_sys=274
2023-06-11 13:53:44 enable power watchdog: 0x0001
2023-06-11 13:54:16 set_voltage_by_steps to 1390.
2023-06-11 13:54:51 set_voltage_by_steps to 1400.
What would cause this to happen?
Chips state is "normal" yet the board wont hash.
https://cdn.shopify.com/s/files/1/0699/5971/3078/files/error.png
Chips state is "normal" yet the board wont hash.
https://cdn.shopify.com/s/files/1/0699/5971/3078/files/error.png
Thanks so much for the quick response.
How do I determine if my ISP uses ipv4 or ipv6? I use Bell Fibe with 1.5 Gbps (fiber optic)
How do I determine if my ISP uses ipv4 or ipv6? I use Bell Fibe with 1.5 Gbps (fiber optic)
Usually, ISP use IPv4 and I think you can check it on network status there are ipv4 and ipv6 connectivity any of this it say connected and no internet.
Or you can use this tool to check https://test-ipv6.com/
SWEET! Looks like I am setup for ipv4 and ipv6 is not setup.
Should I change to solo4.ckpool.org? or does it default to ipv4?
Yes the stratum URL should be the address where you point your miner and the BTC address is your username you can rename it like mybtcaddres.s19j or mybtcaddress and about the password, you can put any or just x it doesn't matter.
About using ipv4 and ipv6 you can also use this pool if your internet supports it and the only purpose is that it is for latency purposes low latency is a must.
About using ipv4 and ipv6 you can also use this pool if your internet supports it and the only purpose is that it is for latency purposes low latency is a must.
Thanks so much for the quick response.
How do I determine if my ISP uses ipv4 or ipv6?
I would like to try my luck at catching a block for 6.25btc. I pay $0.07cents /kw so its better odds than playing the lottery.
How exactly do I setup this ASIC miner to solo mine with ck pool?
Is it really as simple as pointing the address to stratum+tcp://solo.ckpool.org:3333 and using your btc address as the username and x as the password?
Also, what does this mean exactly?
Note that solo.ckpool.org supports both IPV4 and IPV6 transparently.
You may wish to find which is lower latency for you and specify one or the other directly.
IPV4 is solo4.ckpool.org
IPV6 is solo6.ckpool.org
How exactly do I setup this ASIC miner to solo mine with ck pool?
Is it really as simple as pointing the address to stratum+tcp://solo.ckpool.org:3333 and using your btc address as the username and x as the password?
Also, what does this mean exactly?
Note that solo.ckpool.org supports both IPV4 and IPV6 transparently.
You may wish to find which is lower latency for you and specify one or the other directly.
IPV4 is solo4.ckpool.org
IPV6 is solo6.ckpool.org
Earnings right now are at 0.06 per th/s so that's $6.60 per miner.
I am getting paid more using NiceHash.
I average about 31,000 - 33,0000 satoshi's per day with a single 100th machine.
Should I buy two S19j Pro's for $3,700 USD and mine it for the next few years or just buy $3,700 worth of bitcoin (0.16 BTC) ?
My worry is that mining difficulty will keep going up and I will run out of time being profitable before I reach 0.16 BTC.
At the current difficulty of mining, it will take over 250 days to mine 0.16 BTC with two S19j Pro's (assuming electricity is free) but the difficulty will be WAY higher in the next 250 days...
I love the idea of mining because it allows me to dollar cost average into the market and there is no KYC involved.
FYI. You will still need to KYC if you mine your tokens when you are already cashing out your profit to fiat. You will still need CEX no matter what happened if you are planning to get a fiat out of your token investment. My worry is that mining difficulty will keep going up and I will run out of time being profitable before I reach 0.16 BTC.
At the current difficulty of mining, it will take over 250 days to mine 0.16 BTC with two S19j Pro's (assuming electricity is free) but the difficulty will be WAY higher in the next 250 days...
I love the idea of mining because it allows me to dollar cost average into the market and there is no KYC involved.
My hope is that in 2030 when I am ready to get out, there will be other options or that BTC will be accepted for what I want to purchase.
The cost of mining before halving is 14-20 thousand dollars,
Please don't go with this standardized cost of mining.
This is just a gimmick invented by some bored blogger who had no article to write to make his quota.
You can read what other miners, not just me think of it here:
https://bitcointalk.org/index.php?topic=5405856.0
Here on this board there are members with a far lower mining "cost" per BTC and I was one of them too prior to my contract expiring which had way better rates than anything you can possibly get in Europe nowadays. There is no such thing and for sure it ain't in some 25% margin, there are some who average spend 1/5 of a BTC to get one and there are some who mine at break-even point because if they don't they will have to sell all their assets to cover credits and loans.
Buying gear in a bear market is what everyone recommends. These S19j Pro's were selling for $13,000 USD at the peak so I am buying them at an 85% discount.
~
7cents per kw is not far from what the large mining farms are paying.
~
7cents per kw is not far from what the large mining farms are paying.
Of course, buying gear when it's 5x times cheaper is obvious, the thing is that not even that alone can sometimes offset the energy prices.
Let's look at the 7 to 5 cents difference.
3000W running 24 hours is 72kwh, in one instance it is $5.04 in the other is $3.60.
Earnings right now are at 0.06 per th/s so that's $6.60 per miner.
The first miner makes $1.56 second one makes $3, 25% drop in price, and the first miner mines at a loss the second one still makes $1.4.
Same for a difficulty increase with linear price.
Also note, it's not that I'm telling you my crystal ball is 101% sure you're going to lose money, what I want to point out is the risks of doing so and if the KYC thing and the DCA income are enough of an offset for the pain in the ass those miners might turn out to be. Canada you say, so no much of a heat issue but noise and maintenance will still be around.
It sure is a scary time for miners these days. I am surprised hardware is not cheaper.
It's cold where I live so that is an advantage for once!
I just setup an AC Infinity Airlift T16 fan for airflow in my garage. That keeps the S19j Pro fans running at 3500rpm so not much noise anymore.
I am not too concerned with the halving because that usually brings higher highs. I am more worried about the network difficulty.
I can afford to pay for the electricity and hold. I have zero plans to sell until at least 2030.
There is no guarantee that my electric company wont increase cost /kw but I live in a province that has the cheapest electricity in the world due to the massive hydro dams we have here (Quebec, Canada).
What exactly do you mean by "cost of mining before halving is 14-20 thousand dollars" ?
I can afford to pay for the electricity and hold. I have zero plans to sell until at least 2030.
There is no guarantee that my electric company wont increase cost /kw but I live in a province that has the cheapest electricity in the world due to the massive hydro dams we have here (Quebec, Canada).
What exactly do you mean by "cost of mining before halving is 14-20 thousand dollars" ?