Search content
Sort by
Showing 20 of 21 results by gusto88
Re: [440 TH] BitMinter.com [1% PPLNS,Pays TxFees + MergedMining,Stratum,GBT,vardiff]
Currently experiencing connectivity issues with our hosting provider. I'm looking into this now.
It looks like no one is hashing on Bitminter. "Connection refused".Re: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt
Tried this, too. It was actually the first thing I looked up. With continuous ping I could see a time frame <1s where the MR3020 answered on 192.168.1.1. Afterwards ping stopped working again.
Re: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt
This week I bought one MR3020 and flashed it with the technobit firmware (openwrt). Everything worked fine until the switch of the lan interface to dhcp.
The MR3020 started, but no connection was possible. Trying to switch the MR3020 into failsafe mode failed - neither by pressing the WPS button or by change the position of the sidemounted switch. So I bought a CP2102 and followed this guide (no additional resistor was needed).
Afterwards the MR3020 worked again, but this morning the usb psu was defect and I had to use one of my phone usb charges. In the end, I am starting to hate the MR3020.
The MR3020 started, but no connection was possible. Trying to switch the MR3020 into failsafe mode failed - neither by pressing the WPS button or by change the position of the sidemounted switch. So I bought a CP2102 and followed this guide (no additional resistor was needed).
Afterwards the MR3020 worked again, but this morning the usb psu was defect and I had to use one of my phone usb charges. In the end, I am starting to hate the MR3020.
Actually, if you had another router, you can check the DHCP client list or statistic to find the ip address.
For the power supply, i use 5V from same PSU that powered the miner
Alas, as the serial console worked, the problem was obvious. It was configured to use a static ip, but no ip was provided. Hence, I totally bricked it.
Re: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt
This week I bought one MR3020 and flashed it with the technobit firmware (openwrt). Everything worked fine until the switch of the lan interface to dhcp.
The MR3020 started, but no connection was possible. Trying to switch the MR3020 into failsafe mode failed - neither by pressing the WPS button or by change the position of the sidemounted switch. So I bought a CP2102 and followed this guide (no additional resistor was needed).
Afterwards the MR3020 worked again, but this morning the usb psu was defect and I had to use one of my phone usb charges. In the end, I am starting to hate the MR3020.
The MR3020 started, but no connection was possible. Trying to switch the MR3020 into failsafe mode failed - neither by pressing the WPS button or by change the position of the sidemounted switch. So I bought a CP2102 and followed this guide (no additional resistor was needed).
Afterwards the MR3020 worked again, but this morning the usb psu was defect and I had to use one of my phone usb charges. In the end, I am starting to hate the MR3020.
I do not seem to get it right. I did:
wget https://github.com/ckolivas/cgminer/archive/v3.11.0.tar.gz
tar xfz v3.11.0.tar.gz
cd cgminer-3.11.0/
wget https://www.dropbox.com/s/t1rgvsvd6qxjga5/b535bc08267aef90511afff23cb9ec48c4a6a704.patch
patch -p1 < b535bc08267aef90511afff23cb9ec48c4a6a704.patch
./autogen.sh --enable-avalon --enable-hexminerc
sudo make install
But I get this error when doing make install:
Quote
...
gminer-driver-hexminerc.o: In function `hexminerc_send_tasks':
/home/pi/cgminer-3.11.0/driver-hexminerc.c:174: undefined reference to `SHA256_K'
collect2: ld returned 1 exit status
make[1]: *** [cgminer] Error 1
make[1]: Leaving directory `/home/pi/cgminer-3.11.0'
make: *** [install-recursive] Error 1
gminer-driver-hexminerc.o: In function `hexminerc_send_tasks':
/home/pi/cgminer-3.11.0/driver-hexminerc.c:174: undefined reference to `SHA256_K'
collect2: ld returned 1 exit status
make[1]: *** [cgminer] Error 1
make[1]: Leaving directory `/home/pi/cgminer-3.11.0'
make: *** [install-recursive] Error 1
Any ideas?
Code:
./autogen.sh --enable-hexminera --enable-hexminerc
So, again, no refund or real answer. Just laughing at fraud victims.
DON'T BUY FROM TECHNOBIT.EU SCAM COMPANY!
The board is working stable @ 90+ GHs ( about 30+ GHs per chip) 8-10 hours already
Here is the preliminary look of the miner with cooling
http://s27.postimg.org/rxjree3qn/20140119_191324.jpg http://s27.postimg.org/mpz6gugkv/20140119_191428.jpg http://s27.postimg.org/hora8kfov/20140119_191450.jpg
Nicely done. Alas, have you thought about different fan placing? Those two fans look really loud. Maybe something like an AntMiner S1 construction? Where the fan blows horizontal on the board and not from top and bottom? Here is the preliminary look of the miner with cooling
http://s27.postimg.org/rxjree3qn/20140119_191324.jpg http://s27.postimg.org/mpz6gugkv/20140119_191428.jpg http://s27.postimg.org/hora8kfov/20140119_191450.jpg
http://users.atw.hu/ifa/DSC_0056.jpg
http://users.atw.hu/ifa/Screenshot_2014-01-19-14-19-15.png
That has very low performance.. :/
You have six miners, but cgminer only shows five. Something is wrong. 
http://users.atw.hu/ifa/Screenshot_2014-01-19-14-19-15.png
That has very low performance.. :/
My guess is, that a raspberry pi can only handle up to three hex16a2 or ~1200 WU/m
I have 4 hex16a2 on one raspberry pi and similiar GH/s.
you should connect the 24pin atx connector and put in a paperclip or a little piece of power cable in the green and black wire like in the picture , i`don`t know if your fan is going to spin i think it will i have corsair cx 750m and when i put in a paperclip in my green and black wire the fan spins without even connecting any device to the psu..
http://s8.postimg.org/z174nra3l/download.jpg
so do this:
disconnect the psu from the wall socket
connect 24 pin atx
put paperclip in green and black wire
put some electrical tape on top of the paperclip (24 pin connector)
make shure every thing is connected to the HEXc
power on psu
happy hashing
http://s8.postimg.org/z174nra3l/download.jpg
so do this:
disconnect the psu from the wall socket
connect 24 pin atx
put paperclip in green and black wire
put some electrical tape on top of the paperclip (24 pin connector)
make shure every thing is connected to the HEXc
power on psu
happy hashing
This fixed my problem after hourrrssss of trying!!!!!!!!!!!
Just used one online virus scanner on hexminer.exe from the technobit website and only avast recognizes it as a torjan horse (MSIL:BitCoinMiner-B):
https://www.virustotal.com/en/file/45e2e2adad8d9a7811c2e928171d821d6ce0d816f0cdfb4a0061e947b5943b31/analysis/1389839836/
(SHA1, SHA256 and MD5 under "Additional Information")
MSIL:BitCoinMiner-B is not new, there are posts on the internet from 2012. For me this looks like a false positive.
https://www.virustotal.com/en/file/45e2e2adad8d9a7811c2e928171d821d6ce0d816f0cdfb4a0061e947b5943b31/analysis/1389839836/
(SHA1, SHA256 and MD5 under "Additional Information")
MSIL:BitCoinMiner-B is not new, there are posts on the internet from 2012. For me this looks like a false positive.
Hey there everyone!
I am so close but there is still something going wrong.
http://i41.tinypic.com/96bwxs.png
Anyone know why this happens?
Are the boards powered 12v? Doubble check it plsI am so close but there is still something going wrong.
http://i41.tinypic.com/96bwxs.png
Anyone know why this happens?
I have a corsair rm750 connected to the boards.
I am retrying everything again tonight i'll seewhat happens otherwise i'll set up TW.
As it turned out, the Sata To Molex Adapter was touching the board and could not be inserted completly.
A knife and some minor tweaks to the adapters and everything is working fine.
Maybe you could check, if this might be the case with your setup, too.
Any idea when these boards are back in stock (chips included)?
Thanks!
How about ... now!Thanks!
What is the power consumption like?
This.It's the only bit of information I'm missing here.
Re: [CLOSED] NanoFury NF1 USB stick - Group Buy + Product Assembly
any ideas on wether or not this hub would allow over clocking beyond 50 osc6 bits if they were plugged into he 1.2 A ports?
The 1.2A ports only work, if no computer is connected! On the page you will find a footnote:Quote
2 Enter the Fast-Charge Mode by disconnecting the DUB-H7 from your computer, or by powering off your computer. It is recommended that the total power consumption of
the connected USB devices should not exceed 2.4 A, or 12 W.
I would recommend an USB3 Hub. USB3 allows up to 900mA per port.the connected USB devices should not exceed 2.4 A, or 12 W.
any recommendations on one for an rpi?
Re: [CLOSED] NanoFury NF1 USB stick - Group Buy + Product Assembly
any ideas on wether or not this hub would allow over clocking beyond 50 osc6 bits if they were plugged into he 1.2 A ports?
The 1.2A ports only work, if no computer is connected! On the page you will find a footnote:Quote
2 Enter the Fast-Charge Mode by disconnecting the DUB-H7 from your computer, or by powering off your computer. It is recommended that the total power consumption of
the connected USB devices should not exceed 2.4 A, or 12 W.
I would recommend an USB3 Hub. USB3 allows up to 900mA per port.the connected USB devices should not exceed 2.4 A, or 12 W.
Since Bitcoin 0.3.23 the client does not mine bitcoins. Please read the Miner Beginner's Guide and download one of the specialized clients. Also, do not register at deepbit, because it is growing to strong and has already more than 50% of the mining capacity.