Hi Guys.

I've replaced the 2nd psu. still not luck. checked the connectors. found that the 1st psu cpu connector was slightly loose. pushed in and much better as the 2nd fan also started to work. however, only the other blade was now working.
switched off and replaced 2nd psu to stock.

Now it don't hash at all. no info for fans or anything. any ideas ? Im think its the controller board.

[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Reply was 'STATUS=S,When=1392465201,Code=70,Msg=CGMiner stats,Description=cgminer 3.9.0|STATS=0,ID=AVA0,Elapsed=5,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,baud=115200,miner_count=16,asic_count=10,timeout=9,frequency=1300,fan1=0,fan2=0,fan3=0,temp1=0,temp2=0,temp3=0,temp_max=0,Device Hardware%=0.0000,no_matching_work=0,match_work_count1=0,match_work_count2=0,match_work_count3=0,match_work_count4=0,match_work_count5=0,match_work_count6=0,match_work_count7=0,match_work_count8=0,match_work_count9=0,match_work_count10=0,match_work_count11=0,match_work_count12=0,match_work_count13=0,match_work_count14=0,match_work_count15=0,match_work_count16=0,Controller Version=0,Avalon Chip=55,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=537 0|STATS=1,ID=POOL0,Elapsed=5,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=15.99975586,Min Diff=15.99975586,Max Diff=15.99975586,Min Diff Count=339,Max Diff Count=339,Times Sent=4,Bytes Sent=310,Times Recv=6,Bytes Recv=1515,Net Bytes Sent=1101,Net Bytes Recv=1515|'
[STATUS] =>
(
[STATUS] => S
[When] => 1392465201

Code:

=> 70
[Msg] => CGMiner stats
[Description] => cgminer 3.9.0
)
[STATS0] =>
(
[STATS] => 0
[ID] => AVA0
[Elapsed] => 5
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1300
[fan1] => 0
[fan2] => 0
[fan3] => 0
[temp1] => 0
[temp2] => 0
[temp3] => 0
[temp_max] => 0
[Device Hardware%] => 0.0000
[no_matching_work] => 0
[match_work_count1] => 0
[match_work_count2] => 0
[match_work_count3] => 0
[match_work_count4] => 0
[match_work_count5] => 0
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 0
[match_work_count9] => 0
[match_work_count10] => 0
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 0
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 537 0

[quote author=docsham link=topic=379819.msg5150138#msg5150138 date=1392418579]
Hi Twib2,

Thanks for the info. checked the pcie and cpu cables are in the correct sockets. may be the psu.
I'll try another 1000w psu in the morning.

[quote author=twib2 link=topic=379819.msg5149681#msg5149681 date=1392416768]
Your second blade is not hashing - if the 2nd stock PSU is really fine, then maybe a power issue from the connector board? If you have a PCIe swapped with the CPU plug, that can also do that. Luckily if it's a BTMine unit, there's protection and all you have to do is get them in the right connectors and you're good to go. My guess is that both stock PSUs died, one more convincingly than the other. If you have another high-watt PSU, I'd try plopping that in place of the remaining stock PSU.

[quote author=docsham link=topic=379819.msg5149377#msg5149377 date=1392415524]
My MinerNo2 Stock PSUs @ 1300 Freq, recently started dropping hash rate down to almost 0 then went back to 190Ghz. Dropped like this a few times and finally today temperature went really high upto 70C and hash rate dropped to half speed around 95ghz and fan pushing air out stopped too.
Switched off and replaced one of the stock PSU with a 1000W EVGA PSU 80+amps single rail.
Switched back ON and still same 95Ghz or so and 1 fan still don't work.

I have checked the FUSEs on all the modules and all are good.
Looks like 1 blade is totally dead - miners 9-16 :-(

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Reply was 'STATUS=S,When=1392414901,Code=70,Msg=CGMiner stats,Description=cgminer 3.4.3|STATS=0,ID=AVA0,Elapsed=74,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,baud=115200,miner_count=16,asic_count=10,timeout=9,frequency=1300,fan1=0,fan2=2400,fan3=0,temp1=26,temp2=0,temp3=-1,temp_max=26,Device Hardware%=1.5344,no_matching_work=23,match_work_count1=225,match_work_count2=238,match_work_count3=241,match_work_count4=224,match_work_count5=227,match_work_count6=240,match_work_count7=236,match_work_count8=236,match_work_count9=0,match_work_count10=0,match_work_count11=0,match_work_count12=0,match_work_count13=0,match_work_count14=0,match_work_count15=0,match_work_count16=0,Controller Version=2013110865,Avalon Chip=55,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=15928 0|STATS=1,ID=POOL0,Elapsed=74,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=63.00000000,Min Diff=15.00000000,Max Diff=63.00000000,Min Diff Count=3604,Max Diff Count=194,Times Sent=125,Bytes Sent=18235,Times Recv=129,Bytes Recv=19429,Net Bytes Sent=19026,Net Bytes Recv=19429|'
[STATUS] =>
(
[STATUS] => S
[When] => 1392414901
[Code] => 70
[Msg] => CGMiner stats
[Description] => cgminer 3.4.3
)
[STATS0] =>
(
[STATS] => 0
[ID] => AVA0
[Elapsed] => 74
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1300
[fan1] => 0
[fan2] => 2400
[fan3] => 0
[temp1] => 26
[temp2] => 0
[temp3] => -1
[temp_max] => 26
[Device Hardware%] => 1.5344
[no_matching_work] => 23
[match_work_count1] => 225
[match_work_count2] => 238
[match_work_count3] => 241
[match_work_count4] => 224
[match_work_count5] => 227
[match_work_count6] => 240
[match_work_count7] => 236
[match_work_count8] => 236
[match_work_count9] => 0
[match_work_count10] => 0
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 0
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 2013110865
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 15928 0

Still searching this forum.
Hope someone can advise a possible fix.

Thanks
Docsham

[/quote]
[/quote]
[/quote][/code]

docsham

Posts

Merits