Search content
Sort by
Showing 20 of 80 results by malin
now status my unit:
Quote
[Device Hardware%] => 10.8501
[no_matching_work] => 11338
[match_work_count1] => 61200
[match_work_count2] => 0
[match_work_count3] => 88058
[match_work_count4] => 87653
[match_work_count5] => 44001
[match_work_count6] => 0
[match_work_count7] => 87815
[match_work_count8] => 87740
[match_work_count9] => 11698
[match_work_count10] => 79220
[match_work_count11] => 87795
[match_work_count12] => 88235
[match_work_count13] => 87399
[match_work_count14] => 87522
[match_work_count15] => 0
[match_work_count16] => 87564
[no_matching_work] => 11338
[match_work_count1] => 61200
[match_work_count2] => 0
[match_work_count3] => 88058
[match_work_count4] => 87653
[match_work_count5] => 44001
[match_work_count6] => 0
[match_work_count7] => 87815
[match_work_count8] => 87740
[match_work_count9] => 11698
[match_work_count10] => 79220
[match_work_count11] => 87795
[match_work_count12] => 88235
[match_work_count13] => 87399
[match_work_count14] => 87522
[match_work_count15] => 0
[match_work_count16] => 87564
Hi,
Could you tell me how can I check which one capacitor are broked ?
This capacitor by fuses with blue flag it is 16v 330 mikro farrad ?
br
malin
Could you tell me how can I check which one capacitor are broked ?
This capacitor by fuses with blue flag it is 16v 330 mikro farrad ?
br
malin
Much better, looks like you now have 12.5 units functioning, 3.5 not working. Not sure what you mean by "concrete worker" though... 5 and 6 should be near the ribbon cable, so my guess is for those two, the board probably has got the capacitor problem (due to ribbon cable forcing a capacitor to come loose). 12 may be the case on the other blade. Not sure about 2 though - could be that was one that you thought the fuse was OK, but is not? There have been cases of misaligned pins in the backbone board that goes atop the blades, with pins even being bent outside the connector, so it might be worth a close inspection all around, both for loose capacitors and bad connections on the backplane.
K, I repair some fuses arent connect so I create baypases, and now i have like this:
It is some possible to locate concrete worker ?
[STATS] => 0
[ID] => AVA0
[Elapsed] => 479
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 3240
[fan3] => 3000
[temp1] => 24
[temp2] => -1
[temp3] => -1
[temp_max] => 24
[Device Hardware%] => 10.4575
[no_matching_work] => 247
[match_work_count1] => 1618
[match_work_count2] => 0
[match_work_count3] => 1492
[match_work_count4] => 1537
[match_work_count5] => 731
[match_work_count6] => 0
[match_work_count7] => 1534
[match_work_count8] => 1528
[match_work_count9] => 1535
[match_work_count10] => 1373
[match_work_count11] => 1561
[match_work_count12] => 0
[match_work_count13] => 1586
[match_work_count14] => 1471
[match_work_count15] => 1088
[match_work_count16] => 1475
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 26726 0
It is some possible to locate concrete worker ?
[STATS] => 0
[ID] => AVA0
[Elapsed] => 479
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 3240
[fan3] => 3000
[temp1] => 24
[temp2] => -1
[temp3] => -1
[temp_max] => 24
[Device Hardware%] => 10.4575
[no_matching_work] => 247
[match_work_count1] => 1618
[match_work_count2] => 0
[match_work_count3] => 1492
[match_work_count4] => 1537
[match_work_count5] => 731
[match_work_count6] => 0
[match_work_count7] => 1534
[match_work_count8] => 1528
[match_work_count9] => 1535
[match_work_count10] => 1373
[match_work_count11] => 1561
[match_work_count12] => 0
[match_work_count13] => 1586
[match_work_count14] => 1471
[match_work_count15] => 1088
[match_work_count16] => 1475
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 26726 0
You don;t believe, I wake up morning and in api log form 3 AM I have:
[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Socket connect failed: Connection refused
I i;m tired ;/
br
[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Socket connect failed: Connection refused
I i;m tired ;/
br
K, tnx for advice, I will check it tomorrow:)
br
br
Much better, looks like you now have 12.5 units functioning, 3.5 not working. Not sure what you mean by "concrete worker" though... 5 and 6 should be near the ribbon cable, so my guess is for those two, the board probably has got the capacitor problem (due to ribbon cable forcing a capacitor to come loose). 12 may be the case on the other blade. Not sure about 2 though - could be that was one that you thought the fuse was OK, but is not? There have been cases of misaligned pins in the backbone board that goes atop the blades, with pins even being bent outside the connector, so it might be worth a close inspection all around, both for loose capacitors and bad connections on the backplane.
K, I repair some fuses arent connect so I create baypases, and now i have like this:
It is some possible to locate concrete worker ?
[STATS] => 0
[ID] => AVA0
[Elapsed] => 479
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 3240
[fan3] => 3000
[temp1] => 24
[temp2] => -1
[temp3] => -1
[temp_max] => 24
[Device Hardware%] => 10.4575
[no_matching_work] => 247
[match_work_count1] => 1618
[match_work_count2] => 0
[match_work_count3] => 1492
[match_work_count4] => 1537
[match_work_count5] => 731
[match_work_count6] => 0
[match_work_count7] => 1534
[match_work_count8] => 1528
[match_work_count9] => 1535
[match_work_count10] => 1373
[match_work_count11] => 1561
[match_work_count12] => 0
[match_work_count13] => 1586
[match_work_count14] => 1471
[match_work_count15] => 1088
[match_work_count16] => 1475
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 26726 0
It is some possible to locate concrete worker ?
[STATS] => 0
[ID] => AVA0
[Elapsed] => 479
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 3240
[fan3] => 3000
[temp1] => 24
[temp2] => -1
[temp3] => -1
[temp_max] => 24
[Device Hardware%] => 10.4575
[no_matching_work] => 247
[match_work_count1] => 1618
[match_work_count2] => 0
[match_work_count3] => 1492
[match_work_count4] => 1537
[match_work_count5] => 731
[match_work_count6] => 0
[match_work_count7] => 1534
[match_work_count8] => 1528
[match_work_count9] => 1535
[match_work_count10] => 1373
[match_work_count11] => 1561
[match_work_count12] => 0
[match_work_count13] => 1586
[match_work_count14] => 1471
[match_work_count15] => 1088
[match_work_count16] => 1475
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 26726 0
Yep, not good at all - looks like you only have 5.5 workers functioning. If you don't luck out with simply loose connectors, then either you're missing a ton of capacitors or (more likely) you've hit the fuse problem and will need either upgraded fuses or bridges to bypass them (dangerous but I've been running that way OC'd just fine for the last week+ full blast). If your ribbon cable is torn from shipping, that'd do it, too, but no doubt you would have noticed that when you got the unit.
I have in Api Log:
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
To change your fan speeds to slower speed use one these settings in the configurations, more options. depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
Hi,
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I have in Api Log:
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
[STATS] => 0
[ID] => AVA0
[Elapsed] => 240
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[baud] => 115200
[miner_count] => 16
[asic_count] => 10
[timeout] => 9
[frequency] => 1400
[fan1] => 0
[fan2] => 480
[fan3] => 480
[temp1] => 33
[temp2] => -1
[temp3] => -1
[temp_max] => 33
[Device Hardware%] => 6.2112
[no_matching_work] => 170
[match_work_count1] => 1
[match_work_count2] => 0
[match_work_count3] => 734
[match_work_count4] => 750
[match_work_count5] => 408
[match_work_count6] => 0
[match_work_count7] => 0
[match_work_count8] => 746
[match_work_count9] => 0
[match_work_count10] => 678
[match_work_count11] => 0
[match_work_count12] => 0
[match_work_count13] => 0
[match_work_count14] => 696
[match_work_count15] => 0
[match_work_count16] => 0
[Controller Version] => 0
[Avalon Chip] => 55
[USB Pipe] => 0
[USB Delay] => r0 0.000000 w0 0.000000
[USB tmo] => 13141 0
I think it isn't good ?;/
To change your fan speeds to slower speed use one these settings in the configurations, more options. depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
Hi,
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I think that I have problem with measure temp, my fan's have 900-1200 RMPS, and in the www temp show me 36 degree, but when I touch cooler my finger brew, so how may I check the temperature sensor ? where he is located ? I saw that the one grey thin cable is inside.
thanks for advice
thanks for advice
Hi I have maybe stupid noob question but how did you know that you have 5 cold chips ? it is some way to check to boards ?
After the night in the statistics in my mine I have measures form 230GH/s to 140 GH/s, I have to Antminer and there are stable it maybe 2-3% differential.
tnx for advice
br
malin
Actually, that was only my theory IFF you don't have a single "FUSE1" fuse. In the case where there is no "FUSE1" silkscreen marking and corresponding fuse, then (at least on my modules) there are 2 "P" fuses side by side about in the same place, and I would expect that one goes to half the chips and the other to the rest. If it's on a module with a "FUSE1" board, then I don't have a running theory - could be a loose capacitor to half of the VRM, not sure.
This fix didnt solve my 5 cold chips in 1 board. So it's wasnt the Fuse. I measured the fuse before soldering and it was ok.
In this board only 5/10 chips are hashing.
All 5 chips cant be broken something else is broken in the board. I have 2 Boards with 5 cold chips
Anyway there are the FUSE1 & FUSE2 i sodlered good bypass for the fuses
It's hard to tell - did you just connect each end of the fuses to each other or do you actually have solder going across both ends of each fuse?
but how did you know that you have 5 cold chips ? it is some way to check to boards ?After the night in the statistics in my mine I have measures form 230GH/s to 140 GH/s, I have to Antminer and there are stable it maybe 2-3% differential.
tnx for advice
br
malin
Did anyone find a solution to the "half the chips on a module stopped working" problem? I believe there are two unlabeled fuses, and the running theory last I checked was one of these might have blown. I can fix the FUSE1 problem, but not the "5 out of 10 chips cold" issue.
Actually, that was only my theory IFF you don't have a single "FUSE1" fuse. In the case where there is no "FUSE1" silkscreen marking and corresponding fuse, then (at least on my modules) there are 2 "P" fuses side by side about in the same place, and I would expect that one goes to half the chips and the other to the rest. If it's on a module with a "FUSE1" board, then I don't have a running theory - could be a loose capacitor to half of the VRM, not sure.
This fix didnt solve my 5 cold chips in 1 board. So it's wasnt the Fuse. I measured the fuse before soldering and it was ok.
In this board only 5/10 chips are hashing.
All 5 chips cant be broken something else is broken in the board. I have 2 Boards with 5 cold chips
Anyway there are the FUSE1 & FUSE2 i sodlered good bypass for the fuses
It's hard to tell - did you just connect each end of the fuses to each other or do you actually have solder going across both ends of each fuse?
O tnx man its much better !! the noisy is acceptable
br
malin
!! the noisy is acceptable br
malin
To change your fan speeds to slower speed use one these settings in the configurations, more options. depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
--avalon-fan 80-80
--avalon-fan 20-20
Mtnminer
Hi,
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?
best regards
Hi,
That is good idea for someone who are online 24h
, it is free, please use my ref for register.
my ref: http://coingeneration.com/auth/new/366606/
br
malin
That is good idea for someone who are online 24h
, it is free, please use my ref for register.my ref: http://coingeneration.com/auth/new/366606/
br
malin
you say that you use John K escrow, I wait few hours for message form John with that you create escrow for this transaction, alxs create escrow after you so you dont send any message to John for create escrow, that's way I withdraw your offer, you reserve 1 share but you doing nothing for create escrow.
br
malin
br
malin